ignition Alfa Romeo 147 2010 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
81
Warning
light on dialMessage
on display
U
EOBD ENGINE CONTROL SYSTEM FAILURE
In normal conditions, turning the ignition key to MAR, the warning light turns on, but it should
go off when the engine has started. The initial turning on indicates that the warning light is work-
ing properly.
If the warning light stays on or turns on when travelling together with the message + symbol on
the reconfigurable multifunction display:
glowing steadily- means a fault in the supply/ignition system which could cause high emis-
sions at the exhaust, possible lack of performance, poor handling and high consumption levels.
In these conditions it is possible to continue driving without however demanding heavy effort or
high speeds. Prolonged use of the vehicle with the warning light on may cause damage. Contact
Alfa Romeo Authorised Services as soon as possible.
The warning light goes off if the fault disappears, but it is still stored by the system;
flashing- indicates the possibility of damage to catalyst (see “EOBD system” in this chapter).
If the warning light flashes, it is necessary to release the accelerator pedal to lower the speed of
the engine until the warning light stops flashing; continue the journey at moderate speed, trying to
avoid driving conditions that may cause further flashing and contact Alfa Romeo Authorised Ser-
vices as soon as possible.
If, turning the ignition key to MAR, the Uwarning light does not
turn on or if it turns on glowing steadily or flashing when travelling,
contact Alfa Romeo Authorised Services as soon as possible.

GETTING TO KNOW YOUR CAR
83
Warning
light on dialMessage
on display
>
INEFFICIENT ABS SYSTEM
Turning the ignition key to MARthe warning light on the dial lights up, but it should go off after
approx. 4 seconds.
The warning light turns on together with the message + symbol on the reconfigurable multifunc-
tion display, when the system is inefficient. In this case the braking system keeps its effectiveness
unchanged, but without the potential offered by the ABS system. Caution is advisable, particularly
in all cases of less than perfect grip. It is therefore necessary to contact Alfa Romeo Authorised Ser-
vices as soon as possible.
Inefficient EBD electronic braking distributor
x
>
+The car is fitted with electronic braking distributor (EBD). The turning
on at the same time of the xand>warning lights on the dial togeth-
er with the message + symbol on the reconfigurable multifunction display, with
the engine running indicates an EBD system failure; in this case heavy braking
may cause the rear wheels to lock before time, with the possibility of skidding.
Drive extremely carefully to the nearest Alfa Romeo Authorised Service to have
the system checked.
WARNING
The turning on only of the >warning light on the dial together with
the message + symbol on the reconfigurable multifunction display, with
the engine running normally indicates a failure of the ABS system only. In this
case the braking system maintains its effectiveness, without however the an-
tilock function. In these conditions, the effectiveness of the EBD may also be re-
duced, In this case too, you are recommended to contact the nearest Alfa Romeo
Authorised Service immediately, driving in such a way as to avoid sharp brak-
ing, to have the system checked.
WARNING

GETTING TO KNOW YOUR CAR
84
Warning
light on dialMessage
on display
F
PASSENGER’S FRONT AIR BAG DEACTIVATED
With the passenger’s front Air bag engaged, turning the ignition key to MARthe warning light
turns on, but should go off after 4 seconds.
á
VDC SYSTEM (VEHICLE DYNAMICS CONTROL)
Turning the ignition key to MAR, the warning light on the dial turns on and it should go off after
approx. 4 seconds.
If the warning light does not go out or stays on when travelling together with the message +
symbol shown on the reconfigurable multifunction display, contact Alfa Romeo Authorised Services.
The flashing of the warning light when travelling indicates the cutting in of the VDC system.
The warning light turns on when the passenger’s front Air bag is deactivated.
Warning light Findicates also warning light ¬failure. This is
indicated by intermittent flashing, over 4 seconds, of warning light
F. In this event, warning light ¬could be not up to indicate restraint
system failures, if any. Stop the car and ontact Alfa Romeo Authorized Ser-
vices to have the system checked
WARNING

GETTING TO KNOW YOUR CAR
86
Warning
light on dialMessage
on display
SPEED LIMIT EXCEEDED
The warning light turns on together with the message on the display and the sounding of a buzzer
when the car speed exceeds the speed limit set previously (see “Reconfigurable multifunction dis-
play” chapter).
K
FUEL RESERVE
The warning light on the dial turns on together with the message + symbol on the reconfigurable
multifunction display, when about 7 litres of fuel are left in the tank and when autonomy is below
50 km.
AUTONOMY (TRIP COMPUTER)
The message + symbol are shown on the reconfigurable multifunction display when autonomy is
below 50 km.
SCHEDULED MAINTENANCE
This is shown on the reconfigurable multifunction display 2000 km from the deadline given in
the Scheduled Maintenance Programme (every 20,000 km) and it is shown again at timed inter-
vals, turning the ignition key to MARevery 200 km.

GETTING TO KNOW YOUR CAR
92
Air quality control is also entrusted to a
combined particle and activated carbon fil-
ter. The climate control system automatically
controls and adjusts the following parame-
ters and functions:
– temperature of the air admitted to the
passenger compartment (for the driver’s and
passenger’s side separately)
– fan speed
– air distribution
– inside air re-circulation on/off
– climate control compressor on/off en-
able.
It is possible to change the setting of the
following functions manually:
– fan speed
– air distribution
– inside air re-circulation on/off
– climate control compressor on/off en-
able.
The control of functions not changed man-
ually remains automatic and in any case the
temperature of the air admitted to the pas-
senger compartment is controlled automati-
cally according to the temperatures set on
the driver’s and passenger’s displays.
IMPORTANTManual selections prevail
over automatic ones and remain in storage
until the user decides to resume automatic
control. The settings selected manually are
stored when the engine is switched off and
resumed the next time it is started. To ensure correct opera-
tion of the incipient mist-
ing sensor, stickers must
not be applied (road licence holder,
time card etc.) in the “control”
area between the sensor and the
windscreen. Care should also be
given to cleaning the windscreen
and the actual sensor, avoiding the
accumulation of dust and other sub-
stances.IMPORTANTThe demisting procedure
is enabled each time the ignition key is
turned to MARor pressing the
AUTObut-
ton. When this procedure is working it can
be turned off pressing one of the following
buttons: compressor, air re-circulation, air
flow, air capacity. This operation inhibits the
incipient misting sensor signal until the
AU-
TObutton is pressed again or the next time
the ignition key is turned to MAR.
On certain versions, the system is inte-
grated by an antipollution sensor capable of
automatically switching on inside air re-cir-
culation to lessen the harmful effects of pol-
luted air in cities, queues, tunnels and op-
eration of the windscreen washer (with the
typical smell of spirits).
IMPORTANTThe function of the an-
tipollution sensor is subordinate to safety
conditions; therefore disabling the climate
control compressor or at an outside tem-
perature below 4°C the sensor is disabled.
The sensor can be re-enabled pressing the
re-circulation button
vuntil taking it to
the automatic mode. On some versions the system is integrat-
ed with an incipient misting sensor installed
behind the inside rear-view mirror, capable
of “controlling” a predefined area of the
windscreen inner surface which can auto-
matically act on the system to prevent or re-
duce misting through a series of operations
such as: opening air re-circulation, enabling
the compressor, air flow to the windscreen,
fan speed sufficient for demisting; in the
case of heavy misting, enabling the
MAX-
DEFfunction.

GETTING TO KNOW YOUR CAR
106
CONTROLS
TAILGATE OPENING (fig. 91)
Electric tailgate release is only allowed with
the ignition key in the ignition switch at
MARvehicle stationary, at STOPor
PARKfor 3 minutes without opening/clos-
ing a door. To release the tailgate, press but-
ton (A) on the centre console panel.
FOG LIGHTS (fig. 91)
These are turned on pressing button (B)
on the centre console panel, when the out-
er lights are already on, at the same time
the led on the button itself turns on.
Turning the ignition key to STOPthe fog
lights are turned off automatically and do
not come on the next time the engine is
started without pressing button (B).
Press button (B) again to switch off.
IMPORTANTThe front foglights should
be used in compliance with local traffic laws.
fig. 91
A0A0091m
HAZARD WARNING LIGHTS
(fig. 91)
These are switched on by pressing button
(C), on the centre console panel, regardless
of the position of the ignition key.
When the hazard warning lights are
switched on, the switch itself begins to flash
together with the direction indicators and
the direction indicator warning lights on the
instrument cluster. This function is switched
off by pressing the button again.
Use the hazard warning
lights in compliance with
local regulations.
WARNING

GETTING TO KNOW YOUR CAR
107
If no leaks are found the vehicle can be
restarted. Press button (A) to activate the
fuel supply system again.
fig. 92
A0A0318m
REAR FOG GUARDS (fig. 91)
These are turned on, with the dipped beam
headlights or fog lights on, pressing button
(D) on the centre console panel, at the
same time the warning light on the button
itself turns on.
Turning the ignition key to STOPthe fog
guards are automatically turned off and they
do not come on the next time the engine
is started unless button (D) is pressed. To
turn them off press button (D).
IMPORTANTAlways use the rear fog
guards in compliance with local regulations.
DOOR LOCKING SYSTEM
(fig. 91)
To lock the doors simultaneously, press but-
ton (E) on the centre console panel, re-
gardless of the position of the ignition key.
The deterrent led turns on as follows:
– with the ignition key at MARglowing
steadily with a yellow light.
– with the ignition key at STOPflash-
ing with a red light (deterrence condition).
INERTIAL FUEL CUT-OFF
SWITCH
(fig. 92)
This is an automatic safety switch, to be
found on the floor next to the driver’s door
pillar, which is triggered in the event of a
crash of a certain magnitude to interrupt the
flow of fuel.
The cutting in of the inertial switch is shown
on the display of the instrument cluster.If a smell of fuel is noted
following an accident, or
the fuel system is leaking, to avoid
the risk of fire do not reset the
switch.
WARNING

GETTING TO KNOW YOUR CAR
108
HAND BRAKE (fig. 94)
The hand brake lever is located between
the two front seats.
To operate the brake when the vehicle is
stationary, pull lever (A) upwards, until the
required braking action is obtained.
When the ignition key is at MARthe
warning light on the instrument cluster
x
will come on.
fig. 94
A0A0490m
The display (B), in the tachometer shows
the positions during adjustment.
For correct adjustment, bear in mind the
following conditions:
– position 0: one or two people occupy-
ing the front seats
– position 1: five people;
– position 2: five people + load in the
boot;
– position 3: driver + maximum permis-
sible load all stowed in lug-
gage compartment
fig. 93
A0A0467m
HEADLIGHT AIMING DEVICE
(fig. 93)(excluding versions
with Xenon headlights)
The headlights should be aimed correctly
depending on the vehicle load.
To do this, use the rocker button (A), on
the plate at the side of the steering column:
– press the arrow on the button (
A), to
increase by one position (eg.: 0
➟1➟ 2
➟3);
– press the arrow on the button (
S), to
lower by one position (eg.: 3
➟2➟1
➟0).
Adjust the beams every time
the load carried changes.
WARNING
The wheels should be
locked after a few clicks of
the hand brake. If this does not oc-
cur contact Alfa Romeo Authorised
services to have the hand brake
adjusted.
WARNING

GETTING TO KNOW YOUR CAR
111fig. 99
A0A9017g
fig. 100
A0A9081g
With the gearbox in the CITYmode it is
still possible to carry out manual gearshift-
ing, both using the gear lever and the steer-
ing wheel controls. The gearbox remains in
theCITYmode.
The gear engaged (fig. 99) is always sig-
nalled on the display regardless of the se-
lected mode.
N= neutral;
1= first gear;
2= second gear;
3= third gear;
4= fourth gear;
5= fifth gear;
6= sixth gear
R= reverse.Failures of the Selespeed gearbox are sig-
nalled to the driver through a warning light
(
t) connected with the associated fail-
ure message (fig. 100) and accompanied
by an acoustic signal.
SYSTEM ACTIVATION
IMPORTANTWhen the driver’s door is
opened the Selespeed starts the hydraulic
part of the system to prepare it for when the
engine is started. This function (noted by
the turning of the electric pump) is deacti-
vated after 10 door openings/closings not
followed by actual system activation turning
the ignition key.
Turning the ignition switch to MAR, af-
ter about one second, the reconfigurable
multifunction display shows the gear en-
gaged (N,1,2,3,4,5,6,R); from this
moment onwards, the Selespeed system ac-
cepts gearshift commands.
IMPORTANTIf after 10 seconds the re-
configurable display does not show the gear
engaged or the warning light
t(togeth-
er with the message shown by the display)
stays on, turn the ignition key to STOPand
wait for the display to turn off, then repeat
system switch on. If the fault persists, con-
tact Alfa Romeo Authorised Services.

GETTING TO KNOW YOUR CAR
113
STARTING THE ENGINE
The engine can be started either with a
gear engaged or in neutral (N) provided
that the brake pedal is fully depressed.
IMPORTANTIf the brake pedal is not
depressed, the starter motor will not turn,
thus preventing the engine from being start-
ed.
After starting, the gearbox sets to neutral
automatically, the reconfigurable multifunc-
tion display shows the letter (N) and the
system selects the semiautomatic operating
mode (manual).
SWITCHING OFF THE ENGINE
AND SYSTEM DEACTIVATION
Turning the ignition key to STOPthe en-
gine turns off but the Selespeed system is
still active waiting for the car to stop com-
pletely. After about 2 - 4 seconds from when
the key has been moved to STOP, the hy-
draulic part is deactivated and the reconfig-
urable multifunction display is turned off im-
mediately afterwards; at this point is the Se-
lespeed system deactivated.
The gear selected before switching off the
engine remains engaged.
If the engine is stopped with the gearbox
in neutral (N), the buzzer calls the driver’s
attention so that the car can be put in safe-
ty conditions engaging first gear (1) or re-
verse (R). In this case, the ignition key
should be turned to MARand with the
brake pedal pressed, engage first gear (1)
or reverse (R).
IMPORTANTIf the engine is stopped
with the CITYmode engaged, this will be
stored by the system. Indeed, the next time
the engine is started, this condition will still
be active.IMPORTANTShould the engine go off
with the car on the move, the next time it
is started the Alfa Romeo CODE warning
light (Y) may come on. In this case check
that the warning light goes off turning the
engine off and on again with the vehicle sta-
tionary. If not contact Alfa Romeo Authorised
Services.
NEVER leave the car with
the gears in neutral (N).
WARNING
Never remove the ignition
key when the car is mov-
ing. In addition to the fact that the
Selespeed system would not work
properly up to stopping the car, the
steering wheel would lock auto-
matically the first time it is turned.
WARNING
If the engine fails to start
with the gear engaged, the
driver is informed of the potential-
ly dangerous situation due to the
fact that the gearbox is in neutral
by the buzzer and by the reconfig-
urable multifunction display.
WARNING