warning light Alfa Romeo 156 2006 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
139
To release the hand brake:
– slightly lift the lever (A) and press the
release button (B);
– holding the button down lower the lever.
The
x
warning light on the instrument
panel will go out.
To prevent the car from moving acciden-
tally, keep the brake pedal pressed when
engaging the handbrake.WARNINGThe handbrake lever (A) is
fitted with a safety device which prevents
the brake from being released when, if the
lever is pulled, button (B) is pressed. There-
fore, to release the brake, in addition to
pressing button (B), it is also necessary to
pull lever (A) further upwards to release the
safety device, then lower the lever com-
pletely
GEARSHIFT LEVER
(fig. 123)
Depending on the versions the car is fitted
with a five or six speed mechanical gearbox
(see “Technical specifications” chapter).
The position of the individual gears is
shown by the pictogram on the gearshift
lever knob.
When changing gear, always fully depress
the clutch pedal. Before engaging reverse
gear (R) wait for the car to be stationary.
fig. 123
A0B0290m
The wheels should be
locked after a few clicks of
the hand brake. If this does not oc-
cur, contact Alfa Romeo Authorized
Services to have the hand brake
adjusted.
WARNING

GETTING TO KNOW YOUR CAR
140
For 2.5 V6 24V versions and Diesel ver-
sions, to engage reverse gear (R), it is nec-
essary to wait for the car to be stationary,
then raise the ring under the grip (with the
fingers of the same hand holding the lever).
After engaging reverse gear, release the
ring. It is not necessary to raise the ring on
the lever when shifting from reverse to an-
other gear.WARNINGReverse gear can only be en-
gaged with the vehicle completely stopped.
With the engine running, before engaging
reverse gear it is necessary to wait for at
least 3 seconds with the clutch pedal fully
pressed, to avoid grating and the possibil-
ity of damaging the gears.Do not drive with your
hand resting on the
gearshift lever, since the
applied pressure, though slight,
may, with the passing of time,
damage parts inside the gear.
To change gear smoothly,
the clutch pedal must be
fully depressed. Therefore, there
should be no hindrances under the
pedal unit. Make sure that any
mats are well laid and do not in-
terfere with the pedals.
WARNING

GETTING TO KNOW YOUR CAR
142
Failures of Selespeed gearbox are signalled
to the driver through a warning light (B-fig.
126) accompanied by an acoustic signal. The gearbox can work in two operating
modes:
– the first is semiautomatic(then called
MANUAL), in which the driver directly re-
quests gearshifting through the lever on the
centre console or pressing the buttons at the
steering wheel;
– the second is automatic, calledCITY
(mode selectable with the specific button
B-fig. 124, the CITYsign appears on the
display fig. 126fitted on rev-counter), in
which the system decides directly when to
shift gear.With the gearbox in the CITYmode it is
still possible to carry out manual gearshift-
ing, both using the gear lever and the steer-
ing wheel controls. The gearbox remains in
the CITYmode.
The gear engaged (fig. 126) is always
signalled on the display regardless of the se-
lected mode.
N= neutral;
1= first gear;
2 = second gear;
3= third gear;
4= fourth gear;
5= fifth gear;
R= reverse.
fig. 126
A0B0384m

GETTING TO KNOW YOUR CAR
143
SYSTEM ACTIVATIONWARNINGOpening the driver’s door,
the Selespeed starts the hydraulic part of
the system to prepare it for the engine to be
started. This function (noted by the turning
of the electric pump) is deactivated after 10
openings/closings of the door that are not
followed by actual system activation using
the ignition key.
Turning the ignition key to MAR, all the
segments of the display (A-fig. 126), the
gearbox failure warning light (B-fig. 126)
and the word CITYlight up. After about one
second, the display indicates the gear en-
gaged (N, 1, 2, 3, 4, 5, R); from this mo-
ment, the Selespeed system accepts
gearshift commands.
WARNINGIf after 10 seconds the dis-
play segment do not display the gear en-
gaged or the failure warning light stays on,
turn the ignition key to STOPand wait for
the display to go off, then repeat the sys-
tem activation procedure. If the fault per-
sists, contact Alfa Romeo Authorized Ser-
vices
OPERATION WITH THE
ENGINE OFFWARNINGBefore operating the gear-
shift control lever, always check the gear en-
gaged on the display (N, 1, 2, 3, 4, 5, R).
When the engine is off and the vehicle is
stationary, it is possible to engage all the
gears.
With the vehicle stationary and with the
brake pedal pressed, requests to shift gear
are accepted onlyif they are carried out
through the control lever on the central con-
sole.To request gearshifting, in addition to keep-
ing the brake pedal pressed it is necessary to:
– to increase gear (+) (fig. 127) push
the lever “forwards” (if the car is in first gear
this shifts to second, if it is in second gear
it goes to third and so on up to fifth). If the
system is in neutral (N) or reverse (R) the
forward movement on the lever causes en-
gagement of first gear (1).
– to shift down (–) (fig. 127) push the
lever backwards (if the car is in fifth gear
it moves to fourth, if fourth gear is engaged
it shifts to third and so on down to first).
fig. 127
A0B0272m

GETTING TO KNOW YOUR CAR
150
AUTOMATIC OPERATION (CITY)The CITYautomatic operating mode is se-
lected pressing the button (A-fig. 132),
at the base of the gearshift lever.
In addition to the gear, the display on the
rev counter will show the word CITY.
The system decides directly when gearshift-
ing according to the engine running speed
and the driving style.
Quickly releasing the accelerator pedal, the
system does not engage a higher gear in or-
der to maintain an adequate level of engine
brake.
FAILURE SIGNALLINGFailures to the Selespeed gearbox are in-
dicated by the
t
(A-fig. 133) warn-
ing light on the instrument cluster.
When the system is turned on (turning the
ignition key to MAR), the warning light
should turn on glowing steadily for about
4 seconds and then turn off.
If the warning light stays on it means that
a fault to the gearbox has been detected; at
the same time a buzzer sounds intermit-
tently for 4 seconds to attract the driver's
attention.In the case of a fault to the gearshift lever,
the system automatically activates the au-
tomatic CITYmode to allow the car to
reach the nearest Authorized Alfa Romeo
Services to have the fault detected elimi-
nated.
In the event of faults to other components
of the gearbox, the system only allows the
engagement of certain ratios: first gear (1),
second (2) and reverse (R).
fig. 132
A0B0269m
fig. 133
A0B0383m
If the warning light
t
comes on, contact the Alfa
Romeo Authorized Services
as soon as possible to remove the
fault.In case of transmission
fault, contact the Alfa
Romeo Authorized Services as
soon as possible to check the sys-
tem.
WARNING

GETTING TO KNOW YOUR CAR
154
R - Reverse
Move the gearshift lever to Rwith the car
stationary, the engine idling and the brake
pedal pressed.
To prevent accidental engagements, mov-
ing the lever to this position is only allowed
raising the ring (A-fig. 138) placed un-
der the gearshift lever knob.
With the lever in position R the reversing
lights turn on and a beep is sounded for
safety reasons to indicate that reverse gear
has been engaged.
Before moving the lever, press the brake
pedal: the car must be stationary.
WARNINGWith the lever in position R,
reverse gear is not engaged if the vehicle
speed is above the established level. When
the car speed falls below this level, reverse
gear is engaged and remains engaged even
if the speed returns above the limit.
AUTOMATIC OPERATIONSelector lever
For automatic gearshifting, move the
gearshift lever to the right sector
(fig. 138) in one of the following posi-
tions:
P- park (the engine can be started)
R- reverse
N- neutral (the engine can be started)
D- automatic forward gear.
Raise the ring (A-fig. 138) placed un-
der the gearshift lever knob for shifting:
– from Pto Rand vice versa
– from Nto R.P - Park
To prevent accidental engagements, mov-
ing the lever to position Pis only allowed
raising the ring (A-fig. 138) placed un-
der the gearshift lever knob.
When the car is being parked, move the
lever to this position. A device in the gear-
box will lock the driving wheels.fig. 138
A0B0265m
Always pull the hand-
brake completely before
leaving the car.
Move the gearshift lever to posi-
tion P when getting out of the car
leaving the engine running.
WARNING

GETTING TO KNOW YOUR CAR
156
SPORT(button (A-fig. 139)
pressed):
This is selected when wanting to avail of
the vehicle’s peak performance for sporty
driving or on demanding routes.
Driving in the SPORTmode increases fuel
consumption.
WARNINGThe CITYor SPORTdri-
ving modes can be selected under any con-
dition (vehicle stationary or on the move).
WARNINGWhen the car is started with
a cold engine, the system selects the
SPORTdriving mode, even if the CITY
mode has been selected, until the engine
reaches normal operating temperature.
C/S
ICE( button (B-fig. 133) pressed):
This driving mode is recommended when
the road surface offers poor grip (snow, ice,
etc.). Moving off takes place in 2
ndgear.
The ICEdriving mode is available only with
the selector lever at D.
Moving the lever from D, the ICEmode
is automatically cut off.
WARNINGThe ICEdriving mode can
be engaged pressing the corresponding but-
ton also with the car on the move, provided
that the speed is below 45 km/h.
ICE
SELECTING THE DRIVING
MODESThe automatic gearbox for this car is con-
trolled electronically and includes the selec-
tion of three different driving modes, thereby
giving the best response in terms of driving
comfort, consumption levels, sporty perfor-
mance and travelling safety.
The three driving modes CITY, SPORT
and are selected by 2 buttons on the
centre console (fig. 139).
The button (A-fig. 139) selects the
CITYor SPORTfunctions, the button
(B-fig. 139) selects the mode.
With the ignition key at MAR, the driving
mode selected is indicated by the lighting
up of the corresponding word on the display
on the instrument cluster (rev counter):
CITY( button (A-fig. 139)
pressed):
This is used under normal operating con-
ditions; it gives preference to comfortable
driving and balanced consumption control
engaging gears at relatively low engine
speed.
C/S
ICE
ICE
C/SICE
fig. 139
A0B0264m

GETTING TO KNOW YOUR CAR
158
1st2nd3rd4th
2nd2nd4th4th
Gear engaged Gear ratiomanually available
FAULT SIGNALLINGAutomatic gearbox faults are indicated by
the t
warning light (A-fig. 141) on
the instrument cluster as follows:
–warning light glowing steadily
= maximum automatic gearbox oil temper-
ature;
–warning light flashing= automatic
gearbox fault.
Turning the ignition key to MARthe warn-
ing light should turn on and go out after
approx. 4 seconds.
If the warning light stays on or turns on
during travelling, it indicates a gearbox fault
(flashing) or overheated gearbox oil (glow-
ing steadily).Warning light glowing steadily
If the warning light turns on and glows
steadily when the car is travelling, it indi-
cates that the gearbox oil has reached the
maximum established temperature.
The automatic control system provides an
emergency programme.
It is however advisable to stop the car,
move the lever to Por Nand let the engine
idle until the warning light goes out. Resume
driving without demanding high perfor-
mance from the engine.
If the warning light comes on again, it is
necessary to stop again with the engine
idling until it goes out again.
If the interval between one lighting up of
the warning light and the next is below 15
minutes, you are advised to stop the car,
turn off the engine and wait for the engine-
gearbox unit to cool down completely.
fig. 141
A0B0386m
Warning light flashing
The flashing of the warning light when trav-
elling indicates a fault in the automatic gear-
box.
The automatic control system provides an
emergency programme. Under these cir-
cumstances, you are advised to stop the car
and turn off the engine; in fact, the next
time the engine is started, the self-diag-
nostics system could cut off the fault which
will, however, be memorised by the elec-
tronic control device.
Conversely, if the fault remains (warning
light (A- fig. 141) flashing), it is neces-
sary to select the gears manually as if dri-
ving a car with mechanical gearbox, bear-
ing in mind that the only two speeds
available are the 2
ndand 4
thgear, as shown
in the table below:

GETTING TO KNOW YOUR CAR
159
If the indicator light re-
mains flashing, contact the
Alfa Romeo Authorized
Service Centers as soon as possi-
ble to remove the fault.
If a fault is indicated when the engine is
started, this means that the gearbox control
system had detected and memorised a fault
during the journey prior to switching the en-
gine off. In this case, too, contact Alfa
Romeo Authorized Services to have the au-
tomatic gearbox checked over.It is possible to engage reverse gear.
ACOUSTIC WARNINGThis comes into operation for about 18 sec-
onds when:
– the driver’s door is open and/or the en-
gine is off with the selector lever in a posi-
tion other than P;
– position R(reverse) is engaged.PUSH STARTINGStarting the car by pushing or towing is not
possible. In the event of an emergency,
when the battery is flat, start the car with
a suitable emergency battery, following the
instructions given in the chapter “In an emer-
gency”.
When driving with a faulty
gearbox, drive with the ut-
most care considering the restricted
performance levels (in terms of ac-
celeration and speed) the car can
offer.
WARNING
When travelling with a
faulty gearbox, the reverse
lock might not work: absolutely
never move the lever to position
R with the car on the move.
WARNING

GETTING TO KNOW YOUR CAR
161
INTERNAL FITTINGSGLOVEBOX On the dashboard there is a key glovebox
with light.The compartment is lit by a courtesy light
when it is open (when the ignition key is
at MAR(B-fig. 143).
There is a recess on the lid (C-fig. 143)
for inserting a pen or pencil. For the versions
/ markets where provided, the closure flap
is fitted with a lock. The lock can be
opened/closed using the ignition key.
GRAB HANDLES
(fig. 144)
Grab handles are set above the front doors.
Two grab handles (A) fitted with a coat
hook (B) are located above the rear doors.
fig. 142
A0B0587m
fig. 144
A0B0124m
fig. 143
A0B0261m
To open the glovebox use lever (A-
fig. 142).
Do not travel with the
glovebox open; it could
harm the passenger in the event of
an accident.
WARNING