weight Alfa Romeo 159 2010 Owner handbook (in English)

160
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
CORRECT USE
OF THE CAR
For the electric connection a unified con-
nector should be used which is gener-
ally placed on a special bracket normally
fastened to the towing device.
For the electrical connection, 7 pin
12VDC connection is to be used (CU-
NA/UNI and ISO/DIN Standards). Fol-
low the instructions provided by the car
manufacturer and/or the tow hitch man-
ufacturer.
An electric brake or other device (elec-
tric winch, etc.), if required, should be
supplied directly by the battery through
a cable with a cross section of no less
than 2.5 mm
2. In addition to the elec-
trical branches, the car’s electric system
can only be connected to the supply ca-
ble for an electric brake and to the ca-
ble for an internal light, though not
above 15W.Assembly diagram fig. 4
The structure of the tow-hook must be
fixed in the indicated points with
Øwith
n. 2 M10 screws and n. 4 M12 screws.
The fixing points (1) must be provided
with Ø 25x6 mm spacers.
The counter-plates (2) must have a min-
imum thickness of 4 mm.
The counter-plates (3) must have a min-
imum thickness of 6 mm.
IMPORTANTIt is compulsory to fas-
ten a label (plainly visible) of suitable
size and material with the following
wording:
MAX LOAD ON BALL 75 kg
After fitting, screw holes shall be sealed
to prevent exhaust gas inlet.
IMPORTANTThe hook should be fas-
tened to the body avoiding any type of
drilling and trimming of the bumper.
INSTALLING THE TOW HOOK
The towing device should be fastened
to the body by specialised personnel ac-
cording to any additional and/or inte-
grative information supplied by the Man-
ufacturer of the device.
The towing device must meet current
regulations with reference to 94/20/EC
Directive and subsequent amendments.
For any version the towing device used
must match the towable weight of the
car on which it is to be installed.
149-164 Alfa 159 GB 8-04-2009 10:51 Pagina 160

185
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
IN AN
EMERGENCY
Please note:
❒the jack weight is 1.76 kg;
❒the jack requires no adjustment;
❒the jack cannot be repaired. If it
breaks it must be replaced with a
new jack;
❒no tool other than its cranking device
may be fitted on the jack.To change a wheel proceed as follows:
❒Stop the car in a position that is not
dangerous for oncoming traffic where
you can change the wheel safely. The
ground should be flat and adequate-
ly firm;
❒Turn the engine off, pull up the hand-
brake and engage first gear or re-
verse;
❒Using handle A-fig. 2, lift the stiff
cover Band secure it as shown in
fig. 3;
Never tamper with the
inflation valve. Never
place tools between the rim
and tyre. Check and restore, if
required, the pressure of tyres
and spare wheel to the values
given in section “Technical
Specifications”.
WARNING
A0E0132mfig. 2A0E0133mfig. 3
181-222 Alfa 159 GB 3-12-2009 14:10 Pagina 185

249
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
TECHNICAL SPECIFICATIONS
T T
E E
C C
H H
N N
I I
C C
A A
L L

S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S
IDENTIFICATION DATA ........................................ 250
ENGINE CODES - BODYWORK VERSIONS ............... 252
ENGINE .......................................................... 253
FUEL FEED/IGNITION ........................................ 255
TRANSMISSION ............................................... 255
BRAKES........................................................... 256
STEERING........................................................ 256
SUSPENSIONS.................................................. 256
WHEELS.......................................................... 257
DIMENSIONS.................................................... 261
PERFORMANCE................................................. 263
WEIGHTS......................................................... 264
CAPACITIES...................................................... 266
FLUIDS AND LUBRICANTS................................... 267
FUEL CONSUMPTION......................................... 269
CO
2EMISSIONS .............................................. 270
RADIO FREQUENCY REMOTE CONTROL:
MINISTERIAL CERTIFICATIONS ............................. 271
249-270 Alfa 159 GB 3-12-2009 15:51 Pagina 249

250
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
TECHNICAL SPECIFICATIONS
IDENTIFICATION LABEL
This is to be found in the engine com-
partment, aside the upper right shock-
absorber connection and it bears the fol-
lowing identification data:
A.Space for details of national ho-
mologation
B.Space for punching the consecutive
chassis number
IDENTIFICATION
DATA
You are advised to note the identifica-
tion codes. The identification data
stamped and given on the plates and
their position are the following fig. 1:
1- Identification label
2- Body label
3- Bodywork paint identification label
4- Engine label.C.Space available for maximum
weights authorised by various national
regulations
D.Space for version and any supple-
mentary indications to those specified
E.Space for smoke coefficient (diesel
versions only)
F.Space for punching the Manufactur-
er’s name.
A0A0045mfig. 1A0E0013mfig. 2
249-270 Alfa 159 GB 3-12-2009 15:51 Pagina 250

3.2 JTS
4x2
1540
1220
1050
2090
550
1700
70
50
1.9
JTD
M8v
1480
1150
1050
2030
550
1500
60
50
1.9
JTD
M16v
2.0 JTD
M
1490
1130 (Õ)/1150
1050
2040
550
1500
60
50
2.4 JTDM
4x2
1585
1220
1050
2135
550
1500
60
50
1750
TURBO
BENZINA
1430
1100
1050
1980
550
1500
60
50
1.8
140 HP
1385
1100
1050
1935
550
1400
60
50
2.4 JTDM
4x4
1645
1220
1050
2195
550
1500
60
50
3.2 JTS
4x4
1610
1220
1050
2160
550
1700
70
50
264
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
TECHNICAL SPECIFICATIONS
WEIGHTS
Weights (kg)
Saloon versions
Weight empty
(including fluids, 90%
fuel in the tank and
no optional)
Maximum
admitted load (*)
– front axle
– rear axle
– total
Payload including
driver (**)
Towable loads
Max. load on ball
Maximum load
on roof
(*) Loads not to be exceeded. The driver is responsible for arranging the loads in the boot an/or on the roof so
that they comply with these limits.
(**) If special equipment is fitted (sunroof, tow hitch etc.) the unladen weight increases, thus reducing the payload as specified in
the maximum weight allowed.
(
Õ) 2.0 JTDMversions
249-270 Alfa 159 GB 3-12-2009 15:51 Pagina 264

1750
TURBO
BENZINA
1480
1100
1050
2030
550
1500
60
80
3.2 JTS
4x2
1590
1220
1050
2140
550
1800
75
80
1.9
JTD
M8v
1530
1150
1050
2080
550
1500
60
80
1.9
JTD
M16v
2.0 JTD
M
1540
1130 (Õ)/1150
1050
2090
550
1500
60
80
2.4 JTDM
4x2
1635
1220
1050
2185
550
1500
60
80
1.8
140 HP
1435
1100
1050
1985
550
1400
60
80
2.4 JTDM
4x4
1695
1220
1100
2245
550
1500
60
80
3.2 JTS
4x4
1660
1220
1100
2210
550
1800
75
80
265
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
TECHNICAL SPECIFICATIONS
Weights (kg)
Sportwagon versions
Weight empty
(including fluids, 90%
fuel in the tank and
no optional)
Maximum
admitted load (*)
– front axle
– rear axle
– total
Payload including
driver (**)
Towable loads
Max. load on ball
Maximum load
on roof (***)
(*) Loads not to be exceeded. The driver is responsible for arranging the loads in the boot an/or on the roof so
that they comply with these limits.
(**) If special equipment is fitted (sunroof, tow hitch etc.) the unladen weight increases, thus reducing the payload as specified in
the maximum weight allowed.
(***) Lineaccessori Alfa Romeo roof rack, max capacity: 50 kg.
(
Õ) 2.0 JTDMversions
249-270 Alfa 159 GB 3-12-2009 15:51 Pagina 265

286
ALFA 159 SPORTWAGON
PRESETTING FOR
MOUNTING THE
"UNIVERSAL
ISOFIX" CHILD
RESTRAINT SYSTEM
This car is preset for mounting the Uni-
versal Isofix child restraint system, a
new European standardised system for
carrying children safely. fig. 31shows
an example of child restraint system.
The Universal Isofix child's seat covers
weight group 1.
Because of the different attachment sys-
tem, the child seat must be secured by
the specific bottom metal rings
A-fig. 32, located in the squab up-
holstery, in the position marked by
isofix flags (accessible by opening the
zips on the covers) to the specific ring
A-fig. 33located behind the rear seat
squab level with the child seat.A0E0174mfig. 32
A0E0477mfig. 33
fig. 31A0E0241m
271-292 Alfa 159 GB 8-04-2009 10:56 Pagina 286

Rims
– understanding rim marking ... 258
Roof rack/ski rack ............ 106-284
Rubber hoses .......................... 242
Safe lock device ...................... 14
Safety devices.................... 129
S.B.R. system ......................... 131
Seat belts ............................... 130
Seats ..................................... 45
Side/taillights
– bulb replacement ......... 200-203
– control .............................. 70
Ski tunnel ............................... 84
Smart washing ........................ 74
Snow chains ........................... 163
Sound system ......................... 293
Steering ................................. 256
Steering lock ........................... 21
Steering wheel (adjustment) ..... 49
Sun curtains ............................ 88
Sun visors ............................... 88
Sunroof .................................. 93
Suspensions ............................ 256
Symbols ................................. 10
Technical Specifications...... 249
Third brake light ...................... 204
Top speeds .............................. 263
Towing the car ......................... 221
Towing trailers
– installing the tow hook ........ 159
T.P.M.S. system ....................... 122Transmission ........................... 255
Tyres
– changing ........................... 183
– inflation pressures ............... 260
– snow tyres ........................ 162
– standard tyres .................... 259
– understanding tyre marking .. 257
VDC system ........................... 110
Warning lights and
messages.......................... 165
Weights ................................. 264
Wheel geometry ...................... 260
Wheel rims
– understanding rim marking ... 258
Wheels
– changing ........................... 183
– technical data .................... 257
Wheels and tyres ..................... 240
Windows (cleaning) ................. 246
Windscreen washer
– control .............................. 75
– fluid level .......................... 232
Windscreen wiper
– blades .............................. 242
– control .............................. 73
– nozzle .............................. 243 Parking lights
– control .............................. 72
Parking sensors ....................... 118
Performance ........................... 263
Power windows ....................... 99
Pretensioners .......................... 132
Protecting the environment ........ 127
Puddle light
– bulb replacement ................ 208
Quick tyre repair kit
Fix&Go automatic .................. 190
Radio frequency remote control:
ministerial certifications ........... 271
Radio transmitters
and cellular telephones ........... 117
Rain sensor ............................. 74
Rear ceiling lights
– bulb replacement ................ 205
– control .............................. 80
Rear fog lights
– bulb replacement ................ 202
– control .............................. 72
Rearview mirrors ...................... 50
Reconfigurable multifunction
display ................................. 30
Rev counter ............................ 21
Reverse light
– bulb replacement ................ 202
Right hand drive version.. 297
321
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
INDEX
319-328 Alfa 159 GB 3-12-2009 15:53 Pagina 321

PROVISIONS FOR THE PROCESSING OF A VEHICLE
AT THE END OF ITS LIFE-CYCLE
For years now Alfa Romeo has been developing its global commitment towards the safeguarding and protection of the Environment
through the continuous improvement of its production processes and the making of increasingly more “eco friendly” products. With a view
to guaranteeing the best possible service to clients in full observance of environmental standards and in response to the obligations im-
posed by European Directive 2000/53/EC on end-of-life vehicles, Alfa Romeo offers its clients the possibility to hand in their vehicle*
at the end of its life span without additional costs.
The European Directive, in fact, provides for the take-back of the vehicle without the last holder or owner of the same incurring ex-
penses due to the fact that the market value of the vehicle is zero or negative. In particular, in almost all of the countries of the
European Union, up until 1st January 2007, take-back of the vehicle free of charge only applies to vehicles registered from 1 July 2002
on, while, from 2007 on, take-back will be carried out free of charge, independently of the year of registration, provided that the vehi-
cle still contains all its essential component parts (especially engine and body) and is free from additional waste materials.
Our contracted network of authorised treatment facilities has been carefully selected in order to provide a quality service to our customers
by de-polluting and recycling “End of Life Vehicles” to approved environmental standards. To find out the location of your nearest autho-
rised treatment facility, offering free of charge take-back, simply contact one of our dealers or refer to the Alfa Romeo web site or call
the toll free number 00800 2532 0000.
*
Passenger transportation vehicles to seat a max. of nine persons, having a total admissible weight of 3.5 t
319-328 Alfa 159 GB 3-12-2009 15:53 Pagina 322