warning lights Alfa Romeo 166 2008 Owner handbook (in English)
[x] Cancel search | Manufacturer: ALFA ROMEO, Model Year: 2008, Model line: 166, Model: Alfa Romeo 166 2008Pages: 272, PDF Size: 4.17 MB
Page 14 of 272
13
1Air ducts for side window outlets.
2Side air vents.
3Light switch lever (high beam, flash-
ing, direction indicators and controls
for Cruise Control (automatically
keeping a set speed) (if present).
4Instrument cluster.
5Outlets for windscreen.
6Upper outlet.
7Oddments compartment.
8Centre air vents.
9Passenger’s air bag.
10Manual passenger’s side Air bag
deactivation switch.
11Glove box.
12Boot opening button (in glove box).
13Button for rearscreen defrosting,
door mirrors and resistances at base
of windscreen (if present).
14Button for windscreen/front side
windows and door mirrors
defrosting, rearscreen heating,
resistances at base of windscreen (if
present).15Cigar lighter.
16Alfa Romeo I.C.S. (INTEGRATED
CONTROL SYSTEM): RDS radio,
computer on board (TRIP), climate
control, clock and outside/inside
temperature, GSM phone and
navigation system (if present).
17Buttons for central locking, fuel flap
opening, switching off the ASR
function of the VDC system switching
on the STR system (if present).
18Rear fog guard switch.
19Front fog light switch.
20Hazard warning light switch.
21Inside temperature sensor.
22Windscreen wiper/washer control
lever and rain sensor (if present).
23Ignition switch (ignition device).
24Driver’s air bag and horn.
25Lever for releasing/locking adjustable
steering wheel.
26Instrument lighting adjustment.
27Headlamp aiming device control
(except versions with gas discharge
headlights).28Outside lights switch.
29Bonnet opening lever.
30Front floor air outlets.
Page 21 of 272
20
This condition is indicated by a brief
flash of the warning light (A-fig.
10) on the check panel.
If the code has not been recognised cor-
rectly, the Alfa Romeo CODE system
warning light (A-fig. 10) stays on
together with the EOBD/fuel supply-igni-
tion system failure warning light (B-fig.
10) .
In this case, you are recommended to re-
turn the key to the STOPposition and
than back to MAR; if the inhibition per-
sists, try again possibly with the other key
provided with the car. If it is still impossible
to start the car, carry out the emergency
starting procedure described herein and
turn to an Alfa Romeo Authorized Service.
U
¢
¢IMPORTANTEvery electronic key has
its own code, which must be memorised
by the system control unit. To memorise
new keys, up to a maximum of seven,
apply solely to Alfa Romeo Authorized
Services taking with you all the keys in
your possession, the CODE card, a person-
al identity document and the car’s posses-
sion documents.
The codes of the keys
not provided during the
new memorising proce-
dure are erased from the memo-
ry. This is to ensure that any lost
or stolen keys can no longer be
used to start the car.
IMPORTANTThe Alfa Romeo CODE
warning light comes on when travelling
with the ignition key on MAR:
1) If the warning lamp lights up while
the car is moving, it means that the sys-
tem is running a self-diagnosis (e.g. due to
a voltage drop). The first time you stop y-
ou can test the system as follows: switch
the engine off by turning the ignition keytoSTOP; then turn the key back to
MAR: the warning lamp will light up and
should go out in the space of about one
second. If the warning lamp fails to go
out, leave the key at STOPfor more than
30 seconds and repeat the procedure de-
scribed previously. If the problem persists,
contact your Authorised Alfa Romeo Dealer.
2) If the warning lamp flashes it means
that the car is not protected by the immo-
biliser. Contact your Authorized Alfa
Romeo Code Dealer immediately and get
them to store the codes of all the keys in
the memory.
If after about 2 seconds
with the key in the
MAR position, the Alfa
Romeo CODE warning light turns
on again flashing at appr. half
second intervals, this means that
the code of the keys has not
been memorised, thus the car is
not protected by the Alfa Romeo
CODE system against attempted
theft. In this case, contact an Au-
thorized Alfa Romeo Service to
have the key codes memorised.
fig. 10
A0D0091m
Page 24 of 272
23
ACTIVATING THE ALARM
When the doors and boot/bonnet lids
are closed and the ignition key is in the
STOPposition (key removed), point the
remote control towards the car and press
the button on the ignition key.
With the exception of some markets the
system sounds a “BEEP”, the hazard
warning lights turn on for appr. three sec-
onds and the door lock is engaged.
Engagement of the alarm is preceded
by a self-diagnosis characterised by a
change in the frequency at which the led
(A-fig. 12) flashes. If an anomaly is
detected the system gives off a further
“BEEP”.Surveillance
When the system has been turned on,
the led (A-fig. 12) on the dashboard
will flash to indicate that the system is in
the surveillance mode.
The led (A) inside the car flashes
throughout the whole time the vehicle is
under surveillance.
IMPORTANT Operation of the elec-
tronic alarm is adapted at the origin to
the regulations of the different countries.
Self-diagnosis and monitoring of
doors and bonnet/boot
If, after the alarm has been activated, a
second acoustic signal is heard, check
that all the doors and bonnet/boot are
closed properly and engage the system
once again.
On the other hand, if a door or bon-
net/boot lid is not correctly closed it will
not be controlled by the system.
If the control signal is repeated when
the doors and bonnet/boot are closed
properly this means that the self-diagno-
sis function has detected a system operat-
ing fault, in which case it is necessary
contact Alfa Romeo Authorized Services.
DEACTIVATING THE ALARM
To deactivate the alarm press the button
on the remote control. The system per-
forms the following (with the exception
of some markets):
– the direction indicators turn on twice
briefly
– two beeps are sounded briefly by the
siren
– the doors are released.
IMPORTANT If the led in the car s-
tays on when the system has been deac-
tivated, (maximum of 2 minutes or until
the ignition key is moved to MAR) the
following should be borne in mind:
– if the led stays on permanently, it
means that the remote control batteries
are flat and need replacing;
– if the led continues to flash, but at
different intervals than normal, it means
that attempts to steal the car have been
made, counting the number of flashes it
is also possible to identify the type of at-
tempt:
1 flash: right front door
2 flashes: left front door
fig. 12
305PGSm
Page 25 of 272
24
3 flashes: right rear door
4 flashes: left rear door
5 flashes: volumetric sensors
6 flashes: bonnet
7 flashes: boot
8 flashes: tampering with car starting
cables
9 flashes: tampering with battery cables
or cutting emergency key cables
10 flashes: at least three causes of alarm.WHEN THE ALARM IS
TRIGGERED
When the alarm is engaged it will sound
when:
– One of the doors, the bonnet or the
boot is opened.
– The battery is disconnected or the
electric cables are cut, or the emergency
key cables are cut.
– Intrusion into the passenger compart-
ment, e.g. window being broken (volu-
metric protection).
– Attempt to start the engine (key at
MAR).
Depending on the markets, the trigger-
ing of the alarm will activate the siren
and the hazard warning lights (for about
26 seconds). The methods of operation
and the number of cycles may vary de-
pending on the versions/markets. How-
ever a maximum number of cycles is fore-
seen. Once the alarm cycle has come to
an end the system will return to its nor-
mal monitoring state.
SWITCHING OFF THE ALARM
To switch off the alarm, press the re-
mote control button on the key. If the
alarm does not turn off due to a flat re-
mote control battery or system fault,
open the door after unlocking with the
lock key, then place the key in the igni-
tion switch and turn it to MAR.
To turn on the alarm again, turn the key
toSTOPand remove it, then press the
remote control button after leaving the
car and shutting the doors. If the alarm
does not turn on and the led on the re-
mote control gives only one brief flash
while the led on the dashboard stays on
glowing steadily for about 2 minutes, the
key battery should be replaced by a new
one of the equivalent type on sale c/o
normal retailers. To change the battery
follow the instructions given at paragraph
“Key battery change” on previous pages.
If it is not possible to switch on the
alarm with a new remote control battery,
contact Alfa Romeo Authorised Services
to have the system checked.
Page 58 of 272
57
LIGHTS SWITCH AND
STEERING WHEEL
LEVERS
The device and services controlled by
the levers on the steering wheel can only
be activated when the ignition key is in
theMARposition (except the parking
lights which can always be switched on).
LIGHTS SWITCH (fig. 66)
Lights switched off
When the pointer on the knurled ring
(A) is opposite the symbol O, the exter-
nal lights are switched off.
The front air bag is trig-
gered for shocks greater
in magnitude than the pretension-
ers. For impacts between these
two thresholds, it is therefore nor-
mal that only the pretensioners are
triggered.
WARNING
Do not hook rigid objects
to the coat hooks and to
the support handles.
WARNING
The air bag does not sub-
stitute the seat belts, but
only increases their effectiveness.
Moreover, since the front air bags
do not come into operation in the
event of front impact at low
speed, side collisions, bumps from
behind or overturning, in these cir-
cumstances the occupants would
only be protected by the seat belts
which must therefore always be
fastened.
WARNING
fig. 66
A0D0146m
Page 59 of 272
58
Sidelights
The sidelights are switched on by turn-
ing the knurled ring (A) from Oto
6.
The
3warning light on the instru-
ment panel will come on at the same
time.
Dipped-beam headlights
These are switched on by turning the
knurled ring (A) from
6to2.
Parking lights
When the pointer of the switch (A) cor-
responds with the
Fsymbol, the side
lights stay on regardless of the position of
the ignition key.
If moving the left-hand lever (fig. 67)
downward, only the left-hand side park-
ing lights switch on, while moving the
lever upward, only the right-hand side
parking lights switch on.Main-beam headlights (fig. 68)
When the knurled ring in the
2posi-
tion the headlights can be changed form
dipped-beam to main-beam by pushing
the lever towards the dashboard (stable
position).
The
1warning light will come on the
instrument panel.
To return from main-beam to dipped-
beam, once again pull the lever towards
the steering wheel and then release.
LEFT LEVER (fig. 67)
The left lever operates the high beam
lights and the direction indicators.
fig. 67
A0D0014m
A0D0017m
fig. 68
Page 60 of 272
59
Flashing(fig. 69)
The headlights are flashed by pulling the
lever towards the steering wheel (unsta-
ble position) regardless of the position of
the light switch.
The warning light
1on the instrument
panel will come on at the same time.
IMPORTANT Only the main beam
lights are flashed. To avoid penalties, fol-
low local regulations.Direction indicators (fig. 70)
Moving the lever to the stable position:
Up (A) - engages the right-hand direc-
tion indicators.
Down (B) - engages the left-hand direc-
tion indicators.One of the warning lights
Îo¥will
light up on the instrument panel at the
same time.
The lever returns to its home position
automatically and the indicators are
switched off when the steering wheel is
straightened.
IMPORTANT If you wish to signal a
rapid change of direction involving only a
minimum movement of the steering
wheel, the lever can be moved up or
down without it clicking (unstable posi-
tion). When released the lever will return
to its home position.
A0D0018m
fig. 69
A0D0016m
fig. 70
Page 61 of 272
60
RIGHT-HAND LEVER (fig. 72)
The right-hand lever is used to operate
the windscreen wiper and the windscreen
washer.
The control used to activate the wind-
screen washer also activates the head-
light washers (optional for versions/mar-
kets where applicable). “Follow me home” device
(fig. 71)
This function allows the illumination of the
space in front of the car for the length of
time set, and is activated with the ignition
key at STOPor removed, pulling the left-
hand lever towards the steering wheel.This function is activated pulling the lever
within 2 minutes from when the engine is
turned off. At each single movement of the
lever, the staying on of the dipped beams
and sidelights is extended by 30 seconds up
to a maximum of 3.5 minutes; the lights
switch off automatically after the time set.
Each time the lever is operated, the
1
warning light on the cluster turns on.
This function can be interrupted by keep-
ing the lever pulled towards the steering
wheel for more than 2 seconds.
fig. 72
A0D0015m
A0D0018m
fig. 71
Page 64 of 272
63
STR SYSTEM
(SPORT THROTTLE
RESPONSE)
(optional for versions/markets where
applicable)
The STR system offers the driver the
possibility of brilliant, sporty driving with-
out forsaking relaxing driving in other cir-
cumstances with smoother, more gradual
engine response.
In fact, according to preference, the dri-
ver can choose between sporty fast accel-
eration control and smoother more grad-
ual control, for example in city driving.To engage the sporty response (also
when travelling), press the switch (A-
fig. 76) on the centre console. To pre-
vent this function from being engaged un-
intentionally, the system requires the ac-
celerator pedal to be completely released
for engagement. When the sporty re-
sponse is enabled warning light (B) on
the switch lights up.
To restore the most comfortable re-
sponse press the button again (A) and
completely release the accelerator: the
warning light (B) on the switch goes out.
Whenever the engine is switched on,
the control unit positions on the most
comfortable response. If before switching
off the sporty response was stored, it will
automatically be retrieved releasing the
accelerator pedal after the first accelera-
tion.Automatic engagement
The system allows passing from the s-
tandard map to the sporty one with a
quick press on the accelerator. This func-
tion is useful in all situations, such as for
example overtaking or emergency ma-
noeuvres, where maximum acceleration
is needed.
When the need for maximum power
ceases, the system automatically resumes
the standard map.
A0D0022m
fig. 76
Page 71 of 272
70
IMPORTANT Depending on the trim
levels, the dial of the instruments may be
either light grey or black, with green or
red light.
A - Speedometer
IMPORTANT The rev counter may
have different clock values depending on
the different versions of the car.B - Mileage recorder with double
meter display (total and trip)
The display shows:
– the mileage on the first line (6 fig-
ures)
– the trip meter (4 figures) on the sec-
ond line.
Reset the partial km. and hold the push-
button pressed for approx. 1 second (A-
fig. 82).
IMPORTANT The trip meter reading
is not stored if the battery is disconnect-
ed.C - Check panel (fig. 83)
This electronic device checks and indi-
cates any inefficiencies that may adversely
affect running the car and driving safety.
The check panel mainly performs two
functions:
1) Warning lights check.
A0D0025mA0D0120m
fig. 82 fig. 83