air condition Alfa Romeo 4C 2013 Owner handbook (in English)
[x] Cancel search | Manufacturer: ALFA ROMEO, Model Year: 2013, Model line: 4C, Model: Alfa Romeo 4C 2013Pages: 190, PDF Size: 7.87 MB
Page 25 of 190
Aair temperature adjustment knob
(hot/cold air mixing);Binternal air recirculation on/off cursor;Cfan activation/adjustment knob;Dair distribution knob:air from central and side vents and
side diffusers;air from central and side vents,
side diffusers and footwell
diffusers;air from footwell diffusers;air from footwell and side diffusers
and from windscreen diffuser;air from windscreen diffuser and
side diffusers;
HEATING
To heat the passenger compartment,
proceed as follows:
❒ turn knob A to the red section;
❒ turn knob C to the desired speed;
❒ turn knob D to
.
This air distribution allows the
passenger compartment to be heated
quickly.
Then operate the controls to maintain
the desired comfort conditions. IMPORTANT When the engine is cold, it
takes a few minutes to achieve
optimum passenger compartment
heating.
FAST DEMISTING /
DEFROSTING OF
WINDSCREEN AND SIDE
WINDOWS
Proceed as follows:
❒
turn knob A to the red section;
❒ turn knob C to 4 (maximum fan
speed);
❒ turn knob D to
;
❒ bring cursor B to
.
After demisting/defrosting, operate the
controls as normal to restore the
required comfort conditions.
Window demisting
In the event of considerable external
moisture and/or rain and/or large
differences in temperature inside and
outside the passenger compartment,
perform the following preventive
window demisting procedure:
❒ bring cursor B to;
❒ turn knob A to the red section;
❒ turn knob C to 2 (intermediate fan
speed); ❒
turn knob D to
with the possibility
of moving it to position
if window
misting does not occur.
VENTILATION
To ventilate the passenger
compartment properly, proceed as
follows:
❒ fully open the vents and direct them
appropriately;
❒ turn knob A to the blue section;
❒ bring cursor B to;
❒ turn knob C to the desired speed;
❒ turn knob D to
;
INTERNAL AIR
RECIRCULATION
ACTIVATION
Bring cursor B to
.
It is advisable to switch the internal air
recirculation on while standing in
queues or in tunnels to prevent the
introduction of polluted air.
Do not use the function for a long time,
particularly if there are two people on
board, to prevent the windows from
misting.
22
GETTING TO KNOW YOUR CAR
24-9-2013 11:49 Pagina 22
Page 26 of 190
IMPORTANT The internal air
recirculation system makes it possible
to reach the required heating or
ventilation conditions more quickly. Do
not use the internal air recirculation
function on rainy/cold days to avoid the
possibility of the windows misting.
23
24-9-2013 11:49 Pagina 23
Page 28 of 190
Aair temperature adjustment knob
(hot/cold air mixing);Binternal air recirculation on/off cursor;Cfan activation/adjustment knob;Dair distribution knob;Eclimate control compressor on/off
button;Fdoor mirror demisting button.
Knob D enables the air introduced into
the vehicle to reach all areas of the
passenger compartment through five
distribution options:air from central and side vents and
side diffusers;air from central and side vents,
side diffusers and footwell
diffusers;air from footwell diffusers;air from footwell and side diffusers
and from windscreen diffuser;air from windscreen diffuser and
side diffusers;
HEATING
To heat the passenger compartment,
proceed as follows:
❒ turn knob A to the red section;
❒ turn knob C to the desired speed;
❒ turn knob D to
. This air distribution allows the
passenger compartment to be heated
quickly.
Then operate the controls to maintain
the desired comfort conditions.
IMPORTANT When the engine is cold, it
takes a few minutes to achieve
optimum passenger compartment
heating.
FAST DEMISTING /
DEFROSTING OF
WINDSCREEN AND SIDE
WINDOWS
Proceed as follows:
❒
turn knob A to the red section;
❒ turn knob C to 4 (maximum fan
speed);
❒ turn knob D to
;
❒ bring cursor B to
.
After demisting/defrosting, operate the
controls as normal to restore the
required comfort conditions.
IMPORTANT The climate control
system is very useful for speeding up
and maintaining demisting since it
dehumidifies the air. Adjust the controls
as described previously and switch
on the climate control system by
pressing button E. Window demisting
In the event of considerable external
moisture and/or rain and/or large
differences in temperature inside and
outside the passenger compartment,
perform the following preventive
window demisting procedure:
❒
bring cursor B to
;
❒ turn knob A to the red section;
❒ turn knob C to 2 (intermediate fan
speed);
❒ turn knob D to
with the possibility
of moving it to position
if window
misting does not occur.
VENTILATION
To ventilate the passenger
compartment properly, proceed as
follows:
❒ fully open the air diffusers and vents;
❒ turn knob A to the blue section;
❒ bring cursor B to;
❒ turn knob C to the desired speed;
❒ turn knob D to
;
25
24-9-2013 11:49 Pagina 25
Page 29 of 190
INTERNAL AIR
RECIRCULATION
ACTIVATION
Bring cursor B to
.
It is advisable to switch the internal air
recirculation on while standing in
queues or in tunnels to prevent the
introduction of polluted air.
Do not use the function for a long time,
particularly if there are two people on
board, to prevent the windows from
misting.
IMPORTANT The internal air
recirculation system makes it possible
to reach the required heating or
ventilation conditions more quickly. Do
not use the internal air recirculation
function on rainy/cold days to avoid the
possibility of the windows misting.
CLIMATE CONTROL
(cooling)
Proceed as follows:
❒ turn knob A to the blue section;
❒ turn knob C to 1 (1st fan speed). For
rapid cooling, turn knob C to 4
(maximum fan speed).
❒ bring cursor B to;
❒ turn knob D to
;
❒ press button E. Cooling adjustment
Proceed as follows:
❒
bring cursor B to
;
❒ turn knob A toward the red section to
increase the temperature;
❒ turn knob C anticlockwise to reduce
the fan speed.
DOOR MIRROR
DEMISTING
Press the
button F fig. 21 to
activate this function.
Activation is indicated by the digital
warning light on the display.
Press thebutton again to
deactivate the function.
SYSTEM MAINTENANCE
In winter, the climate control system
must be turned on at least once a
month for about 10 minutes. Have the
system inspected at a dedicated Alfa
Romeo Dealership before the summer.
3)
IMPORTANT
3) The system uses R-1234yf
coolant which does not pollute the
environment in the event of
accidental leakage. Under no
circumstances should you use
R-134a fluid which, in addition to
being incompatible with the
system’s components, contributes
greatly to the greenhouse effect.
26
GETTING TO KNOW YOUR CAR
24-9-2013 11:49 Pagina 26
Page 58 of 190
WARNING
46) The presence of the TPMS doesnot permit the driver to neglect
regular checks of the tyre
pressure, including for the spare
wheel.
47) Tyre pressure must be checked with tyres rested and cold. Should
it become necessary for whatever
reason to check pressure with
warm tyres, do not reduce
pressure even though it is higher
than the prescribed value. Repeat
the check when the tyres are
cold.
48) Should one or more wheels be fitted without sensors, the system
will no longer be available and,
in addition to the TPMS warning
light flashing for less than one
minute before becoming constant,
a warning message will be shown
on the display, until 4 wheels
with sensors are fitted again. 49) The TPMS cannot warn of
sudden decreases in tyre pressure
(for example when a tyre bursts).
In this case, stop the car, braking
with caution and avoiding abrupt
steering.
50) Replacing standard tyres with winter tyres (and vice versa)
requires TPMS adjustment that
must only be performed by a
dedicated Alfa Romeo Dealership.
51) Changes in outside temperature may cause tyre pressures to vary.
The TPMS system may
temporarily indicate insufficient
pressure. In this case, check the
tyre pressure when cold and, if
necessary, restore the inflation
values.
52) When a tyre is removed, it is advisable to replace the rubber
valve seal as well: contact a
dedicated Alfa Romeo Dealership.
Tyre and/or rim fitting/removal
operations require specific
precautions; to avoid damaging or
fitting the sensors incorrectly,
tyre and/or rim fitting/removal
operations should only be carried
out by specialised staff. Contact
a dedicated Alfa Romeo
Dealership. 53) Strong radio-frequency
interference could inhibit the
regular operation of the TPMS.
This condition will be indicated by
a message on the display. The
message will disappear
automatically as soon as the
radio-frequency interference
ceases to affect the system.
54) The tyre repair kit (Fix&Go) provided with the car (for
versions/markets, where
provided) is compatible with the
TPMS sensors; using sealants not
equivalent with that in the original
kit may adversely affect its
operation. If sealants not
equivalent with the original one
are used, it is recommended to
have the TPMS sensors checked
by a qualified repair centre.
55
24-9-2013 11:49 Pagina 55
Page 79 of 190
Warning lights onpanel What it means
What to do
amberTPMS
IMPORTANT Do not continue driving with one or
more flat tyres as handling may be
compromised. Stop the car, avoiding sharp
braking and steering. Repair immediately using
the dedicated kit (see "Repairing a wheel"
paragraph in the "In an emergency" chapter)
and contact the dedicated Alfa Romeo
Dealership as soon as possible.
TPMS failure
The warning light switches on when a fault is
detected in the TPMS.
Should one or more wheels be fitted without
sensors, the display will show a warning message
until initial conditions are restored. In this case, contact the dedicated Alfa Romeo
Dealership as soon as possible.
Low tyre pressure - See manual
The warning light switches on, together with a
dedicated message on the display, to indicate that
the tyre pressure is lower than the recommended
value and/or that slow pressure loss is occurring. In
these circumstances, optimal tyre duration and fuel
consumption may not be guaranteed.
Should two or more tyres be in the condition
mentioned above, the display will show the
indications corresponding to each tyre in
sequence. In any situation in which the message on the
display is "See manual", it is ESSENTIAL to refer
to the contents of the "Wheel" paragraph in the
"Technical data" chapter, strictly complying with
the indications that you find there.
76
KNOWING THE INSTRUMENT PANEL
24-9-2013 11:49 Pagina 76
Page 101 of 190
Passenger front airbag
This is located in a dedicated
compartment in the dashboard fig. 72.
74)
GENERAL WARNINGS
The front airbags may activate in the
event of sharp impacts to the
underbody of the car (e.g. impact with
steps, pavements, potholes or road
bumps, etc.).
When the airbag deploys it emits a
small amount of dust: the dust is
harmless and does not indicate the
beginning of a fire. The dust may irritate
the skin and eyes however: in this
case, wash with neutral soap
and water.
Airbag checking, repair and
replacement must be carried out at a
dedicated Alfa Romeo Dealership.If the car is scrapped, have the airbag
system deactivated at a dedicated
Alfa Romeo Dealership.
Pretensioners and airbags are deployed
according to different logics on the
basis of the type of collision. Failure to
deploy of one of the devices does
not necessarily indicate a system
malfunction.
77) 78) 79) 80) 81) 82) 83)
WARNING
72) Do not apply stickers or other
objects to the steering wheel or
the passenger side airbag cover.
Do not place objects on the
passenger side of the dashboard
because these could interfere
with the correct opening of the
passenger airbag and cause injury
to occupants.
73) Always drive keeping your hands on the steering wheel rim so that
the airbag can inflate freely if
necessary. Do not drive with your
body bent forward. Keep the
backrest in straight position,
resting correctly your back on it. 74) Instructions to deactivate the
passenger's front airbag can be
found in the "Menu Options"
paragraph of the "Knowing the
instrument panel" chapter. Please
note that under these conditions
the airbag will NOT deploy in case
of need (accident).
75) Do not rest your head, arms or elbows on the door to prevent
injury during airbag deployment.
76) Never lean your head, arms and elbows out of the window.
77) If the
warning light does not
switch on when the key is turned
to MAR-ON, or stays on while
driving (on some versions
together with a message on the
display) there may be a fault in the
restraint systems. In this case,
airbags or pretensioners may not
be activated in the case of an
accident or (in a lesser number of
cases) they may be activated
incorrectly. Before proceeding,
contact a dedicated Alfa Romeo
Dealership to have the system
checked immediately.
78) Do not travel carrying objects on your lap, in front of your chest or
between your lips (pipe, pencils,
etc.): they could cause severe
injury if the airbag is deployed.
72
A0L0056
98
SAFETY
24-9-2013 11:50 Pagina 98
Page 115 of 190
❒sprinkle talcum powder on the rubber
blade of the windscreen wiper and lift
it off the glass (for the correct lifting
procedure, refer to the "Windscreen
wiper" paragraph in the
"Maintenance and care" chapter);
❒ cover the car with a cloth or
perforated plastic sheet. Do not use
sheets of non-perforated plastic
as they do not allow moisture on the
car body to evaporate;
❒ inflate tyres to +0.5 bar above the
standard prescribed pressure and
check it periodically;
❒ do not drain the engine cooling
system;
❒ every time the car is left inactive for
two weeks or longer, run the air
conditioning system for about
5 minutes, set to outside air and with
fan set to maximum, with the engine
idling; this operation will ensure
adequate lubrication to minimise the
possibility of damage to the
compressor when the system is put
back into operation; ❒
ensure that the air intake directly in
front of the windscreen is not
obstructed by leaves or other foreign
bodies; any leaves in the air intake
could reduce the air flow and, if they
enter the reservoir, could prevent
water drainage. In winter months,
make sure that the air intake is not
obstructed by ice, mud or snow.
IMPORTANT After turning the ignition
key to STOP, wait at least 1 minute
before disconnecting the electrical
supply to the battery.
112
STARTING AND DRIVING
24-9-2013 11:50 Pagina 112
Page 137 of 190
SCHEDULED
SERVICINGCorrect servicing is essential in
guaranteeing a long life for the car
under the best conditions.
This is why Alfa Romeo has
programmed a series of checks and
servicing operations every 20,000 km.
Check the items on the Scheduled
Servicing Plan (e.g. periodically check
level of liquids, tyre pressure, etc.)
before 20.000 km and between these
services deadlines.Scheduled Servicing is offered by the
dedicated Alfa Romeo Dealership
at predefined intervals. If, during each
operation, in addition to the ones
scheduled, the need arises for further
replacements or repairs, these may
be carried out only with your explicit
agreement.
IMPORTANT
2000 km before the maintenance is
due, a dedicated message appears on
the display, along with
warning
light. The Scheduled Servicing services are
set out by the Manufacturer. Failure
to have them carried out may invalidate
the warranty.
It is advisable to inform the dedicated
Alfa Romeo Dealership of any small
operating irregularities without waiting
for the next service.
134
SERVICING AND MAINTENANCE
24-9-2013 11:50 Pagina 134
Page 140 of 190
Thousands of kilometres20 40 60 80 100 120
Months 12 24 36 48 60 72
Replace the air cleaner cartridge ●●●●●●
Change engine oil and replace oil filter (**)
Change brake fluid (or every 24 months) ●●●(**) The actual interval for changing the oil and replacing the engine oil filter depends on the vehicle usage conditions and is signalled by the warning light or
message (if present) on the instrument panel or every 12 months.
137
24-9-2013 11:50 Pagina 137