steering wheel Alfa Romeo 4C 2014 Owner handbook (in English)

WARNING
46) The presence of the TPMS doesnot permit the driver to neglect
regular checks of the tyre
pressure, including for the spare
wheel.
47) Tyre pressure must be checked with tyres rested and cold. Should
it become necessary for whatever
reason to check pressure with
warm tyres, do not reduce
pressure even though it is higher
than the prescribed value. Repeat
the check when the tyres are
cold.
48) Should one or more wheels be fitted without sensors, the system
will no longer be available and,
in addition to the TPMS warning
light flashing for less than one
minute before becoming constant,
a warning message will be shown
on the display, until 4 wheels
with sensors are fitted again. 49) The TPMS cannot warn of
sudden decreases in tyre pressure
(for example when a tyre bursts).
In this case, stop the car, braking
with caution and avoiding abrupt
steering.
50) Replacing standard tyres with winter tyres (and vice versa)
requires TPMS adjustment that
must only be performed by a
dedicated Alfa Romeo Dealership.
51) Changes in outside temperature may cause tyre pressures to vary.
The TPMS system may
temporarily indicate insufficient
pressure. In this case, check the
tyre pressure when cold and, if
necessary, restore the inflation
values.
52) When a tyre is removed, it is advisable to replace the rubber
valve seal as well: contact a
dedicated Alfa Romeo Dealership.
Tyre and/or rim fitting/removal
operations require specific
precautions; to avoid damaging or
fitting the sensors incorrectly,
tyre and/or rim fitting/removal
operations should only be carried
out by specialised staff. Contact
a dedicated Alfa Romeo
Dealership. 53) Strong radio-frequency
interference could inhibit the
regular operation of the TPMS.
This condition will be indicated by
a message on the display. The
message will disappear
automatically as soon as the
radio-frequency interference
ceases to affect the system.
54) The tyre repair kit (Fix&Go) provided with the car (for
versions/markets, where
provided) is compatible with the
TPMS sensors; using sealants not
equivalent with that in the original
kit may adversely affect its
operation. If sealants not
equivalent with the original one
are used, it is recommended to
have the TPMS sensors checked
by a qualified repair centre.
55
24-9-2013 11:49 Pagina 55

Warning lights onpanel What it means
What to do
amberTPMS
IMPORTANT Do not continue driving with one or
more flat tyres as handling may be
compromised. Stop the car, avoiding sharp
braking and steering. Repair immediately using
the dedicated kit (see "Repairing a wheel"
paragraph in the "In an emergency" chapter)
and contact the dedicated Alfa Romeo
Dealership as soon as possible.
TPMS failure
The warning light switches on when a fault is
detected in the TPMS.
Should one or more wheels be fitted without
sensors, the display will show a warning message
until initial conditions are restored. In this case, contact the dedicated Alfa Romeo
Dealership as soon as possible.
Low tyre pressure - See manual
The warning light switches on, together with a
dedicated message on the display, to indicate that
the tyre pressure is lower than the recommended
value and/or that slow pressure loss is occurring. In
these circumstances, optimal tyre duration and fuel
consumption may not be guaranteed.
Should two or more tyres be in the condition
mentioned above, the display will show the
indications corresponding to each tyre in
sequence. In any situation in which the message on the
display is "See manual", it is ESSENTIAL to refer
to the contents of the "Wheel" paragraph in the
"Technical data" chapter, strictly complying with
the indications that you find there.
76
KNOWING THE INSTRUMENT PANEL
24-9-2013 11:49 Pagina 76

Main safety rules to be
followed when carrying
children
❒Follow the instructions supplied with
the child restraint system itself, which
the manufacturer must provide.
Keep the instructions in the car along
with the other documents and this
handbook. Do not use child restraint
systems without instructions;
❒ always check that the seat belt is well
fastened by pulling on it;
❒ only one child is to be strapped into
each restraint system; never carry
two children using one child restraint
system;
❒ always check that seat belts do not
rest on the child’s neck;
❒ while travelling, do not let the child sit
incorrectly or release the belts;
❒ never carry children on your lap, even
newborns. No-one could restrain
them in the event of an accident;
❒ in the event of an accident, replace
the child restraint system with a
new one.
FRONT AIRBAGSDRIVER AND
PASSENGER FRONT
AIRBAGS
The car features multistage front
airbags (“Smart bag system”) for driver
and passenger.
The front driver/passenger airbags are
designed to protect occupants in the
event of frontal impacts of medium-high
severity, by placing the bag between
the occupant and the steering wheel or
dashboard.
Therefore, non-activation of the front
airbags in other types of collisions (side
collisions, rear shunts, rollovers, etc.)
does not indicate a system malfunction.
Airbags are not a replacement of but
complementary to the seat belts, which
you are recommended to always wear.
In the event of impact, those not
wearing a seat belt are projected
forwards and may come into contact
with the bag which is still inflating. The
protection offered by the bag is
compromised in these circumstances.
72)
Front airbags may not activate in the
following situations: ❒
frontal impacts against highly
deformable objects not involving the
front surface of the car (e.g. wing
collision against guard rail);
❒ jamming of the car underneath other
vehicles or protective barriers (e.g.
underneath a truck or a guard rail); in
this case, the bags would offer no
additional protection with respect to
the seat belt and their deployment
would be inappropriate. In these
cases, non-deployment does not
indicate a system malfunction.
Driver front airbag
This is located in a dedicated
compartment in the centre of the
steering wheel fig. 71.
73)
71
A0L0055
97
24-9-2013 11:50 Pagina 97

Passenger front airbag
This is located in a dedicated
compartment in the dashboard fig. 72.
74)
GENERAL WARNINGS
The front airbags may activate in the
event of sharp impacts to the
underbody of the car (e.g. impact with
steps, pavements, potholes or road
bumps, etc.).
When the airbag deploys it emits a
small amount of dust: the dust is
harmless and does not indicate the
beginning of a fire. The dust may irritate
the skin and eyes however: in this
case, wash with neutral soap
and water.
Airbag checking, repair and
replacement must be carried out at a
dedicated Alfa Romeo Dealership.If the car is scrapped, have the airbag
system deactivated at a dedicated
Alfa Romeo Dealership.
Pretensioners and airbags are deployed
according to different logics on the
basis of the type of collision. Failure to
deploy of one of the devices does
not necessarily indicate a system
malfunction.
77) 78) 79) 80) 81) 82) 83)
WARNING
72) Do not apply stickers or other
objects to the steering wheel or
the passenger side airbag cover.
Do not place objects on the
passenger side of the dashboard
because these could interfere
with the correct opening of the
passenger airbag and cause injury
to occupants.
73) Always drive keeping your hands on the steering wheel rim so that
the airbag can inflate freely if
necessary. Do not drive with your
body bent forward. Keep the
backrest in straight position,
resting correctly your back on it. 74) Instructions to deactivate the
passenger's front airbag can be
found in the "Menu Options"
paragraph of the "Knowing the
instrument panel" chapter. Please
note that under these conditions
the airbag will NOT deploy in case
of need (accident).
75) Do not rest your head, arms or elbows on the door to prevent
injury during airbag deployment.
76) Never lean your head, arms and elbows out of the window.
77) If the
warning light does not
switch on when the key is turned
to MAR-ON, or stays on while
driving (on some versions
together with a message on the
display) there may be a fault in the
restraint systems. In this case,
airbags or pretensioners may not
be activated in the case of an
accident or (in a lesser number of
cases) they may be activated
incorrectly. Before proceeding,
contact a dedicated Alfa Romeo
Dealership to have the system
checked immediately.
78) Do not travel carrying objects on your lap, in front of your chest or
between your lips (pipe, pencils,
etc.): they could cause severe
injury if the airbag is deployed.
72
A0L0056
98
SAFETY
24-9-2013 11:50 Pagina 98

88) The car must be locked after afew clicks of the parking brake: if
this is not so, contact the
dedicated Alfa Romeo Dealership
to have it adjusted. Always park
the vehicle safely as indicated by
the Highway Code and as
described above.
USING THE
TRANSMISSIONThe 4C features the TCT 6-speed twin
dry clutch transmission with steering
wheel controls. This is an advanced
technical solution which combines the
control of a manual gearbox, the
immediacy of a sequential system and
the convenience of being able to select
an automatic selection programme
without the slowdown of a conventional
automatic transmission.
With the key removed from the ignition,
the system will not implement any
action when the buttons on the
transmission control panel on the
central tunnel fig. 74 are pressed,
irrespective of the pressure applied to
the brake pedal. Therefore, the
transmission will remain in the condition
that it was in when the engine was
switched off. With car stationary and key at MAR-ON
(ignition-operated electrical services
activated), the screen displays the gear
engaged and the active operating
mode (automatic =
AUTOor manual =
no display).
OPERATING MODES
The transmission can operate in two
operating modes (except when the
"Race" mode is selected):
❒ the first manual type (MANUAL), in
which the driver decides directly
when to change gear;
❒ the second completely automatic
(AUTO), in which the system decides
when to change gear.
When the "Race" mode is selected, the
only allowed operating mode is
MANUAL.
Manual operation
(MANUAL)
In this operating mode, the driver is
responsible for choosing the best gear
to engage, depending on the car
operating conditions.
Use the “+” steering wheel stalk to
engage a higher gear, or the “–” stalk to
engage a lower gear (see the following
paragraph, "Steering wheel stalks").74
A0L0067
104
STARTING AND DRIVING
24-9-2013 11:50 Pagina 104

LEVERS ON THE
STEERING WHEEL
These enable sequential gear shifting
fig. 77.
– steering wheel stalk "+(pulling stalk
towards driver, see fig. 78): engage
higher gear;
– steering wheel stalk "– (pulling stalk
towards driver, see fig. 78): engage
lower gear. The engagement of a lower (or higher)
gear is only permitted if the engine
rpm allow it.
STARTING THE CAR
To start the engine press the brake
pedal: the system engages neutral (N)
automatically.
After the starting procedure, 1st gear
(1) or reverse (R) can be engaged.
Irrespective of the mode selected
(AUTO/MANUAL), to engage 1st gear
or reverse (R), it is necessary to press
the brake pedal and press the
1button
on the transmission control panel (or
the "+" steering wheel stalk) to engage
1st gear or the Rbutton to engage
reverse.
When 1st gear is engaged, the system
sets itself to AUTOmode.
Neutral (N) can be engaged again by
pressing the Nbutton with the brake
pedal pressed.
When the 1,Nor Rbuttons are
pressed (or "+" steering wheel stalk is
operated) without pressing the brake
pedal, no gear change request is
implemented by the system.
IMPORTANT Reverse cannot be
engaged by pressing the "-" stalk on
the steering wheel. Important information
If starting is requested with a
transmission failure (see "Warning lights
and messages" paragraph), carry out
the “Delayed start-up” procedure: when
the key is turned to AVV for at least 7
seconds with brake pedal pressed, the
engine will be started. The system will
remain in “recovery” condition.
If the engine does not start, contact a
dedicated Alfa Romeo Dealership.
When the driver's door is opened, the
system activates the hydraulic
components so that they are prepared
for the subsequent engine starting.
MOVING THE CAR
The car can set off both in 1st gear and
reverse (R).
Notes (concerning car
start-up)
The gears can only be engaged by
pressing the brake pedal. If the brake
pedal is not depressed, the display will
show a dedicated message.
It is not possible to set off in a higher
gear than 1st: if this is attempted,
the display shows a dedicated
message.77
A0L0071
78
A0L0072
106
STARTING AND DRIVING
24-9-2013 11:50 Pagina 106

When setting off on a medium-steep
incline, it is advisable to engage the
handbrake.
Engaging 1st gear
Proceed as follows:
❒press the brake pedal;
❒ press the 1button on the
transmission control panel;
❒ release the brake pedal and press
the accelerator pedal.
Engaging reverse (R)
Reverse (R) can only be engaged with
car stationary and brake pedal pressed.
Proceed as follows:
❒ press the brake pedal (car completely
stationary);
❒ press the R button on the
transmission control panel;
❒ release the brake pedal and press
the accelerator pedal. When reverse
is engaged, the system emits an
acoustic signal (for versions/markets,
where provided).
If the brake pedal is not depressed (and
the car is stationary), the display will
show a dedicated message and the
system will automatically engage
neutral (N). IMPORTANT With the car running, the
request is accepted and executed if the
car speed drops below 3 km/h within
3 seconds from the request: if the
request is not executed, the system will
maintain the gear engaged or, if the
speed of the car drops below 10 km/h,
will put the transmission in neutral (N)
and the manoeuvre will have to be
repeated.
ENGAGING NEUTRAL (N)
With car stationary and ignition key at
MAR-ON (irrespective of the condition
of the engine), neutral (N) can only
be engaged with the brake pedal
pressed.
If the car is in motion, neutral (N) can
always be engaged, irrespective of the
pressure applied to the brake and
accelerator pedals.
The display will show the letter
N
together with the active operating
mode.
With car in motion, to engage a gear
from the neutral (N) position, press the
1 button on the transmission control
panel (it is not necessary to press
the brake pedal): the transmission will
immediately engage the correct gear
according to the car’s speed. With car stationary and ignition key at
MAR-ON (irrespective of the condition
of the engine), 1st gear can only be
engaged with the brake pedal pressed.
LAUNCH CONTROL
The "Launch Control" strategy permits
high-performance starting.
This strategy can be activated with
vehicle at a standstill, Dynamic or Race
mode selected and 1st gear engaged.
The sequence of operations to perform
is as follows:
❒
press the brake pedal and hold it
down;
❒ press the accelerator pedal and hold
it down;
❒ press the "–" stalk behind the
steering wheel;
When the brake pedal is released, the
car will start with maximum
acceleration.
89)
To abandon the strategy, simply
interrupt the above sequence
of operations or release the accelerator
pedal.
107
24-9-2013 11:50 Pagina 107

REPLACING
EXTERIOR BULBSFRONT LIGHT CLUSTERS
These contain the bulbs for the side
lights/daytime running lights (DRL),
dipped beam headlights, main beam
headlights and direction indicators. The
bulbs are arranged as follows fig. 87:ASide lights/daytime running lightsBDipped/main beam headlightsCDirection indicators
To replace the bulbs for the dipped and
main beam headlights and for the
direction indicators open the
corresponding protective flaps on the
inner wheel arch fig. 88 that can be
located by steering the wheel
completely. A - direction indicator bulb protective
flap
B - dipped/main beam headlight bulb
protective flap
Side lights/daytime
running lights (DRL)
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.
Dipped/main beam
headlights
To change the bulb, proceed as follows:
❒
steer the wheel completely;
❒ open the protective flap B fig. 88 by
rotating the fixing screw;
❒ take out the electric connector A fig.
89 and then rotate the bulb holder B
clockwise and remove it; ❒
extract the bulb and replace it;
❒ refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector A;
❒ close the protective flap B fig. 88.
Direction indicators
Front
To change the bulb, proceed as follows:
❒ steer the wheel completely;
❒ open the protective flap A fig. 88 by
rotating the fixing screw;
❒ take out the electric connector A fig.
90 and then rotate the bulb holder B
clockwise and remove it;
❒ extract the bulb and replace it;
❒ refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector A;87
A0L0091
88
A0L0092
89
A0L0093
122
IN AN EMERGENCY
24-9-2013 11:50 Pagina 122

IMPORTANT
16) Be careful to position the liftarms correctly at the points
illustrated, in order to prevent
damage to the carbon fibre
chassis and the bodywork
components.
17) To avoid damage to the carbon fibre chassis, the car cannot be
raised with standard hydraulic
jacks, only with suitable lowered
hydraulic jacks. Contact a
dedicated Alfa Romeo Dealership.
TOWING THE CAR
18)
The tow hook provided with the car is
located in the tool box in the luggage
compartment.
ATTACHING THE TOW
HOOK
Take tow hook A and tighten it fully
onto the threaded pin fig. 109.
110) 111) 112)
IMPORTANT
18) The tow hook attachment is onlyavailable at the front end of the
car.
WARNING
110) Before towing, turn the ignitionkey to MAR-ON and then to STOP
without removing it. The steering
column will automatically lock
when the key is removed and the
wheels cannot be steered. Also
check that the gearbox/
transmission is in neutral (N).
111) When towing, remember that the assistance of the brake servo
is absent. Consequently, more
force is required at the pedal
in order to brake. Do not
use flexible cables when towing
and avoid jerky movements. Make
sure not to damage parts in
contact with the car while towing.
When towing the car, you must
comply with all specific traffic
regulations, both in terms of the
towing device and behaviour
on the road. Do not start the
engine while towing the car.
Before tightening the ring, clean
the threaded housing thoroughly.
Make sure that the ring is fully
screwed into the housing before
towing the car.
109
A0L0107
130
IN AN EMERGENCY
24-9-2013 11:50 Pagina 130

IMPORTANT
5) Detergents cause water pollution.Only wash your car in areas
equipped to collect and treat
wastewater from this type
of activity.
IMPORTANT
27) In order to preserve the aestheticappearance of the paint abrasive
products and/or polishes should
not be used for cleaning the car.
28) Avoid washing with water cannons, rollers and/or brushes in
washing stations. Then, wash
the car, only by hand, using
pH-neutral detergents; dry it with
a wet chamois leather.
INTERIORS
132) 133)
Periodically check the cleanliness of the
interior, beneath the mats, also to
prevent damage to carbon parts.
To remove and reposition the mats in
the passenger compartment, proceed
as follows:
❒undo the screws with folding ring A
fig. 123, driver side and passenger
side;
❒ separate the Velcro fabric strips B in
the front area under the mats, lifting
them from the floor.
Reposition the mats on the floor,
making sure that the holes at the back
of the mats coincide with the screw
housings on the floor.
To reposition, proceed as follows: ❒
tighten the screws with folding ring A
fig. 123 in the housings on the floor;
❒ unite the Velcro fabric strips of the
mats with those on the floor, taking
care to apply light pressure and
ensure that the fastening is efficient.
134)
SEATS AND FABRIC OR
MICROFIBRE PARTS
Remove dust with a soft brush or a
vacuum cleaner. For better cleaning of
microfibre trim (including the steering
wheel, for versions/markets, where
provided) we advise you to moisten the
brush. Rub the seats with a sponge
moistened with a solution of water and
neutral detergent.
LEATHER SEATS
(for versions/markets, where provided)
Remove the dry dirt with a chamois
or slightly damp cloth, without exerting
too much pressure. Remove any liquid
or grease stains using an absorbent
dry cloth, without rubbing. Then clean
with a soft cloth or chamois moistened
with water and mild soap. If the stain
persists, use specific products and
observe the instructions carefully.
123
A0L0143
151
24-9-2013 11:50 Pagina 151