warning lights Alfa Romeo 4C 2014 Owner handbook (in English)

Warning lights ondisplay What it means
What to do
redENGINE COOLANT TEMPERATURE
TOO HIGH
The digital warning light switches on when
the key is turned to MAR-ON, but it should
switch off after a few seconds. The warning
light switches on when the engine is
overheated.
The display shows the dedicated message. When driving normally: stop the car, switch off the
engine and check that the water level in the reservoir is
not below the MIN mark. If it is, wait for the engine to
cool down then slowly and carefully open the cap, top
up with coolant and check that the level is between the
MIN and MAX marks on the reservoir. Also check
visually for any fluid leaks. Should the warning light turn
on again at the next start-up, contact the dedicated
Alfa Romeo Dealership.
If the car is used under demanding conditions (e.g. in
high-performance driving): slow down and, if the
warning light stays on, stop the car. Wait for 2 or 3
minutes with the engine running and slightly
accelerated to further favour the coolant circulation.
Then stop the engine. Check the correct coolant level
as described above.
IMPORTANT Over demanding routes, it is advisable to
keep the engine on and slightly accelerated for a few
minutes before switching it off.
Warning lights on
display What it means
What to do
redALTERNATOR FAILURE
The digital warning light switches on, only with
engine started, when an alternator fault is
detected.
Contact the dedicated Alfa Romeo Dealership as
soon as possible.
81
24-9-2013 11:49 Pagina 81

Warning lights ondisplay What it means
What to do
redGEARBOX FAILURE
The digital warning light switches on when the
key is turned to MAR-ON, but it should switch off
after a few seconds.
The digital warning light flashes (together with a
message in the display and an acoustic signal) to
indicate that the gearbox/transmission is faulty.
The digital warning light can light up even in the
event of transmission overheating, after a
particularly demanding use. In this case an engine
performance limitation is performed. Contact the dedicated Alfa Romeo Dealership as
soon as possible.
If it is necessary to start the engine with a
gearbox/transmission failure, follow the procedure
described in the "Using the gearbox/
transmission" paragraph, "Starting the engine"
section in the "Starting and driving" chapter.red
INCOMPLETE DOOR LOCKING
(for versions/markets, where provided)
The digital warning light on the display switches
on when one or more doors are not properly shut.
An acoustic signal is emitted with the doors open
and the car in motion.amber
WORN BRAKE PADS
(for versions/markets, where provided)
The digital warning light on the display switches
on when the front or rear brake pads are worn.
The display shows the dedicated message.
Have them replaced as soon as possible.amberALFA ROMEO CODE SYSTEM FAILURE
(for versions/markets, where provided)
The digital warning light switches on in the display
(together with a message) to indicate Alfa Romeo
CODE system failure.
Contact the dedicated Alfa Romeo Dealership as
soon as possible.
82
KNOWING THE INSTRUMENT PANEL
24-9-2013 11:49 Pagina 82

Warning lights ondisplay What it means
What to do
amberFUEL RESERVE/LIMITED RANGE
The digital warning light switches on in the display
when about 4–5 litres of fuel are left in the tank.
63)
amberFUEL RESERVE/LIMITED RANGE SENSOR
FAULT
The digital warning light switches on in the display
when a fuel reserve sensor fault is detected. The
display shows the dedicated message.
Contact the dedicated Alfa Romeo Dealership as
soon as possible.greenCRUISE CONTROL
(for versions/markets, where provided)
The digital warning light switches on in the display
when the ignition key is turned to MAR-ON, but it
should switch off after a few seconds, if the
Cruise Control is deactivated.
The digital warning light switches on when the
Cruise Control ring nut is turned to the ON
position (see the “Cruise Control” paragraph in
the "Knowing your car" chapter).
The display shows the dedicated message.green
DOOR MIRROR DEMISTING/DEFROSTING
The digital warning light switches on in the display
when the
button on the control panel is
pressed.
83
24-9-2013 11:49 Pagina 83

Warning lights ondisplay What it means
What to do
amberEXTERIOR LIGHTS FAULT
The symbol and corresponding message appear
on the display if a fault is detected in one of the
following lights:
❒
daytime running lights (DRL)
❒ side lights
❒ dipped headlights
❒ direction indicators
❒ rear fog lights
❒ reversing lights
❒ number plate lights.
The fault relating to these lights may be caused
by: one or more blown fuses, one or more blown
bulbs or a broken electrical connection. Check, and if necessary replace the fuses
involved, in accordance with the "Fuse
replacement" paragraph in the "In an emergency"
chapter; if this does not resolve the fault, check,
and if necessary replace, the bulbs involved, in
accordance with the "External bulb replacement"
paragraph in the "In an emergency" chapter.
Should this operation also fail to resolve the fault,
contact the dedicated Alfa Romeo Dealership, for
a comprehensive check of the electrical system.amber
SERVICE (SCHEDULED SERVICING)
The
digital warning light is automatically
displayed, along with a dedicated message, with
key at MAR-ON, 2,000 km (or equivalent value in
miles) before the following scheduled servicing
interval and is activated again every 200 km (or
equivalent value in miles). Contact a dedicated Alfa Romeo Dealership. The
operations in the “Scheduled Servicing Plan” will
be performed and the message will be reset.
84
KNOWING THE INSTRUMENT PANEL
24-9-2013 11:49 Pagina 84

Warning lights ondisplay What it means
What to do
GENERAL FAILURE
(for versions/markets, where provided)
The symbol lights up in the display in the
circumstances indicated below.
Engine oil pressure sensor failure
The symbol lights up when the engine oil pressure
sensor is faulty. The display shows the dedicated
message.In these case contact the dedicated Alfa Romeo
Dealership to have the fault fixed as soon as
possible.
"Clutch overheating" message
The
symbol, along with a message on the
display, lights up to indicate clutch overheating.
If the driver continues, the
symbol will switch
off and the
warning light will light up (on some
versions together with a message on the display)
to indicate a transmission failure. If the
symbol lights up along with a message
on the display, reduce gear shifting and/or
change usage conditions, until the normal
operating conditions are restored.
If thewarning light lights up (a message will
appear on the display, on some versions) stop
immediately, operate the handbrake, stop the
engine and wait 5 minutes: after this, normal
transmission operating conditions will be
restored.
Should the transmission failure condition persist,
contact the dedicated Alfa Romeo Dealership
FUEL CUT-OFF
The symbol and the corresponding message are
shown on the display in the following cases:
❒ fuel cut-off system intervention: the yellow
symbol lights up;
❒ fuel cut-off system failure: the red symbol lights
up. For the fuel cut-off system reactivation procedure,
refer to the "Fuel Cut-Off System" section of the
"Controls" paragraph, in the "Knowing your car"
chapter. If it is still not possible to restore the fuel
supply, contact the dedicated Alfa Romeo
Dealership.
85
24-9-2013 11:49 Pagina 85

Warning lights ondisplay What it means
What to do
LUGGAGE COMPARTMENT OPEN
The symbol and the corresponding message are
shown on the display.POSSIBLE ICE ON ROAD
The symbol and corresponding message appear
on the display when the outside temperature is
below or equal to 3°C.
IMPORTANT In the event of outside temperature
sensor failure, the digits that indicate the value are
replaced by dashes.BRAKE LIGHTS FAILURE
The symbol and corresponding message appear
on the display if a fault is detected in the brake
lights.The fault may be caused by a blown bulb, a
blown protection fuse or an interruption of the
electrical connection.PARKING SENSOR FAILURE
The symbol and corresponding message appear
on the display if there is a parking sensor failure.
DISPLAY OF SELECTED DRIVING MODE
(“Alfa DNA” system)
A letter (d, n, or a) corresponding to the active
driving mode (dynamic or race, normal, all
weather) and a dedicated message are shown on
the display.
86
KNOWING THE INSTRUMENT PANEL
24-9-2013 11:49 Pagina 86

LEVERS ON THE
STEERING WHEEL
These enable sequential gear shifting
fig. 77.
– steering wheel stalk "+(pulling stalk
towards driver, see fig. 78): engage
higher gear;
– steering wheel stalk "– (pulling stalk
towards driver, see fig. 78): engage
lower gear. The engagement of a lower (or higher)
gear is only permitted if the engine
rpm allow it.
STARTING THE CAR
To start the engine press the brake
pedal: the system engages neutral (N)
automatically.
After the starting procedure, 1st gear
(1) or reverse (R) can be engaged.
Irrespective of the mode selected
(AUTO/MANUAL), to engage 1st gear
or reverse (R), it is necessary to press
the brake pedal and press the
1button
on the transmission control panel (or
the "+" steering wheel stalk) to engage
1st gear or the Rbutton to engage
reverse.
When 1st gear is engaged, the system
sets itself to AUTOmode.
Neutral (N) can be engaged again by
pressing the Nbutton with the brake
pedal pressed.
When the 1,Nor Rbuttons are
pressed (or "+" steering wheel stalk is
operated) without pressing the brake
pedal, no gear change request is
implemented by the system.
IMPORTANT Reverse cannot be
engaged by pressing the "-" stalk on
the steering wheel. Important information
If starting is requested with a
transmission failure (see "Warning lights
and messages" paragraph), carry out
the “Delayed start-up” procedure: when
the key is turned to AVV for at least 7
seconds with brake pedal pressed, the
engine will be started. The system will
remain in “recovery” condition.
If the engine does not start, contact a
dedicated Alfa Romeo Dealership.
When the driver's door is opened, the
system activates the hydraulic
components so that they are prepared
for the subsequent engine starting.
MOVING THE CAR
The car can set off both in 1st gear and
reverse (R).
Notes (concerning car
start-up)
The gears can only be engaged by
pressing the brake pedal. If the brake
pedal is not depressed, the display will
show a dedicated message.
It is not possible to set off in a higher
gear than 1st: if this is attempted,
the display shows a dedicated
message.77
A0L0071
78
A0L0072
106
STARTING AND DRIVING
24-9-2013 11:50 Pagina 106

WARNING
92) Indicate the presence of thestationary car in accordance with
current regulations: hazard
warning lights, warning triangle,
etc. Those on board should get
out of the vehicle and wait for the
wheel to be repaired away from
the threat posed by the traffic.
If parked on a slope or rough
surface, chock the wheels with
wedges or other suitable devices
(for the correct procedure for
parking the car safely, refer to the
"Parking" paragraph in the
"Starting and driving" chapter).
93) Give the booklet to the technicians who will be handling
the tyre that was treated using
the "Fix&Go automatic" kit.
94) A repair is not possible if the wheel rim is damaged (groove
is deformed, causing air to
escape). Do not remove foreign
bodies (screws or nails) from the
tyre. 95) Do not use the compressor for
more than 20 consecutive
minutes. Risk of overheating. The
kit is not suitable for definitive
repairs, so the repaired tyres may
only be used temporarily.
96) The bottle contains ethylene glycol and latex: it may cause
an allergic reaction. It is harmful if
swallowed. Eye irritant. It may
cause sensitisation if inhaled or
on contact. Avoid contact with
eyes, skin and clothes. In the
event of contact, rinse
immediately with plenty of water.
If ingested, do not induce
vomiting. Rinse out your mouth,
drink large quantities of water and
seek immediate medical attention.
Keep out of the reach of children.
The product must not be used
by asthmatics. Do not inhale the
vapours during insertion and
suction. Call a doctor immediately
if allergic reactions are noted.
Store the bottle in its special
compartment, away from sources
of heat. The sealant has an expiry
date. Replace the bottle if the
sealant has expired.
97) Wear the protective gloves provided with the kit. 98) Apply the adhesive label where it
can be easily seen by the driver as
a reminder that the tyre has been
treated with the quick repair kit.
Drive carefully, especially on
corners. Do not exceed 80 km/h.
Avoid sudden acceleration or
braking.
99) If the pressure has fallen below 1.8 bar, do not drive any further:
the Fix&Go automatic quick tyre
repair kit cannot guarantee proper
hold because the tyre is too
damaged. Contact a dedicated
Alfa Romeo Dealership.
100) Always indicate that the tyre was repaired using the quick
tyre repair kit. Give the booklet to
the personnel charged with
handling the tyre treated with the
repair kit.
117
24-9-2013 11:50 Pagina 117

REAR FOG LIGHT/
REVERSING LIGHT
104)
To replace the rear fog light bulbs A fig.
94 or the reversing lights B fig. 94
proceed as follows:
❒turn the bulb holder C fig. 95
anticlockwise, extract the bulb and
replace it. 3
rd
BRAKE LIGHTS
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.
NUMBER PLATE LIGHTS
To replace the bulbs proceed as
follows:
❒ adjust the lens A in the point shown
in figure fig. 96 laterally to compress
the retaining clip, then pull the
number plate light cluster A out;
❒ turn bulb holder B fig. 97
anticlockwise, extract bulb C and
replace it.
WARNING
104) The rear fog light and the
reversing light are located close to
the exhaust pipes; take the
utmost care not to get burnt
during the bulb replacement.
94
A0L0097
95
A0L0126
96
A0L0136
97
A0L0099
124
IN AN EMERGENCY
24-9-2013 11:50 Pagina 124

SCHEDULED SERVICING PLAN1750 Turbo Petrol VERSIONSThousands of kilometres20 40 60 80 100 120
Months 12 24 36 48 60 72
Check battery charge status and recharge if necessary ●●●●●●
Check tyre conditions/wear and adjust pressure, if required ●●●●●●
Check operation of lighting system (headlights, direction
indicators, hazard warning lights, luggage compartment,
passenger compartment, glove compartment, instrument panel
warning lights, etc.) ●●●●●●
Check vehicle fastenings ●●●
Check mechanical components fastenings ●●●●●●
Check operation of windscreen wiper/washer system and adjust
jets, if necessary ●●●●●●
Check position/wear of windscreen wiper blade ●●●●●●
Check cleanliness of boot lock, cleanliness and lubrication of
linkages ●●●●●●
Visually inspect condition of: exterior bodywork, carbon
monocoque, aerodynamic bottom, pipes and hoses (exhaust, fuel
supply system, brakes), rubber elements (boots, driveshaft boots,
sleeves, bushes, etc.) ●●●●●●
Check condition and wear of front brake pads and discs, and
operation of pad wear indicator ●●●●●●
135
24-9-2013 11:50 Pagina 135