warning light Alfa Romeo 4C 2014 Owner handbook (in English)

Warning lights ondisplay What it means
What to do
GENERAL FAILURE
(for versions/markets, where provided)
The symbol lights up in the display in the
circumstances indicated below.
Engine oil pressure sensor failure
The symbol lights up when the engine oil pressure
sensor is faulty. The display shows the dedicated
message.In these case contact the dedicated Alfa Romeo
Dealership to have the fault fixed as soon as
possible.
"Clutch overheating" message
The
symbol, along with a message on the
display, lights up to indicate clutch overheating.
If the driver continues, the
symbol will switch
off and the
warning light will light up (on some
versions together with a message on the display)
to indicate a transmission failure. If the
symbol lights up along with a message
on the display, reduce gear shifting and/or
change usage conditions, until the normal
operating conditions are restored.
If thewarning light lights up (a message will
appear on the display, on some versions) stop
immediately, operate the handbrake, stop the
engine and wait 5 minutes: after this, normal
transmission operating conditions will be
restored.
Should the transmission failure condition persist,
contact the dedicated Alfa Romeo Dealership
FUEL CUT-OFF
The symbol and the corresponding message are
shown on the display in the following cases:
❒ fuel cut-off system intervention: the yellow
symbol lights up;
❒ fuel cut-off system failure: the red symbol lights
up. For the fuel cut-off system reactivation procedure,
refer to the "Fuel Cut-Off System" section of the
"Controls" paragraph, in the "Knowing your car"
chapter. If it is still not possible to restore the fuel
supply, contact the dedicated Alfa Romeo
Dealership.
85
24-9-2013 11:49 Pagina 85

Warning lights ondisplay What it means
What to do
LUGGAGE COMPARTMENT OPEN
The symbol and the corresponding message are
shown on the display.POSSIBLE ICE ON ROAD
The symbol and corresponding message appear
on the display when the outside temperature is
below or equal to 3°C.
IMPORTANT In the event of outside temperature
sensor failure, the digits that indicate the value are
replaced by dashes.BRAKE LIGHTS FAILURE
The symbol and corresponding message appear
on the display if a fault is detected in the brake
lights.The fault may be caused by a blown bulb, a
blown protection fuse or an interruption of the
electrical connection.PARKING SENSOR FAILURE
The symbol and corresponding message appear
on the display if there is a parking sensor failure.
DISPLAY OF SELECTED DRIVING MODE
(“Alfa DNA” system)
A letter (d, n, or a) corresponding to the active
driving mode (dynamic or race, normal, all
weather) and a dedicated message are shown on
the display.
86
KNOWING THE INSTRUMENT PANEL
24-9-2013 11:49 Pagina 86

IMPORTANT
6) If the
warning light switches on when driving, stop the engine immediately and contact the dedicated Alfa
Romeo Dealership.
WARNING
62) Deteriorated engine oil should be replaced as soon as possible after the digital warning light comes on, and never more than 500 km after it first switches on. Failure to observe the above indications may result in severe damage to
the engine and invalidate the warranty. Remember that when the digital warning light comes on, it does not mean
that the level of engine oil is low, so if it flashes you must not top up the engine oil.
63) If the warning light flashes with the car in motion, contact the dedicated Alfa Romeo Dealership.
87
24-9-2013 11:49 Pagina 87

SBR SYSTEM (Seat
Belt Reminder)
IN BRIEF
This system comprises an acoustic
warning which, in conjunction with
the
warning light flashing on the
instrument panel, advises the driver if
their seat belt has not been fastened.
Contact the dedicated Alfa Romeo
Dealership to deactivate this acoustic
warning permanently.
The acoustic warning can be
reactivated at any time through the
Setup Menu (see "Menu Options"
paragraph in “Knowing the
instrument panel” section).
If the driver side seat belt is not
fastened, when 20 km/h is exceeded or
when travelling at a speed from 10 to
20 km/h for longer than 5 seconds, an
acoustic signal sequence will be started
(continuous acoustic signal for the first
6 seconds followed by 90 seconds
of intermittent beeping) and the
warning light will flash. The warning light will stay on constantly
at the end of the cycle until the engine
is stopped. The acoustic signal is
interrupted immediately when the seat
belt is fastened.
If the seat belt is unfastened again
when driving the car, the acoustic signal
and the flashing warning light resume
as described previously.
PRETENSIONERSThe car is equipped with seat belt
pretensioners, which draw back the
seat belts by several centimetres in the
event of a strong frontal impact. This
guarantees the perfect adherence
of the seat belts to the occupant's
bodies before the retention action
begins.
It is evident that the pretensioners have
operated when the belt withdraws
toward the retractor.
This car is also equipped with a second
pretensioner (in the kick plate area). Its
activation is signalled by the shortening
of the metal cable.
A slight discharge of smoke may be
produced during the activation of the
pretensioner which is not in harmful and
does not involve any fire hazard.
IMPORTANT To obtain the highest
degree of protection from the action of
the pretensioner, wear the seat belt
tight to the chest and pelvis.
92
SAFETY
24-9-2013 11:49 Pagina 92

Passenger front airbag
This is located in a dedicated
compartment in the dashboard fig. 72.
74)
GENERAL WARNINGS
The front airbags may activate in the
event of sharp impacts to the
underbody of the car (e.g. impact with
steps, pavements, potholes or road
bumps, etc.).
When the airbag deploys it emits a
small amount of dust: the dust is
harmless and does not indicate the
beginning of a fire. The dust may irritate
the skin and eyes however: in this
case, wash with neutral soap
and water.
Airbag checking, repair and
replacement must be carried out at a
dedicated Alfa Romeo Dealership.If the car is scrapped, have the airbag
system deactivated at a dedicated
Alfa Romeo Dealership.
Pretensioners and airbags are deployed
according to different logics on the
basis of the type of collision. Failure to
deploy of one of the devices does
not necessarily indicate a system
malfunction.
77) 78) 79) 80) 81) 82) 83)
WARNING
72) Do not apply stickers or other
objects to the steering wheel or
the passenger side airbag cover.
Do not place objects on the
passenger side of the dashboard
because these could interfere
with the correct opening of the
passenger airbag and cause injury
to occupants.
73) Always drive keeping your hands on the steering wheel rim so that
the airbag can inflate freely if
necessary. Do not drive with your
body bent forward. Keep the
backrest in straight position,
resting correctly your back on it. 74) Instructions to deactivate the
passenger's front airbag can be
found in the "Menu Options"
paragraph of the "Knowing the
instrument panel" chapter. Please
note that under these conditions
the airbag will NOT deploy in case
of need (accident).
75) Do not rest your head, arms or elbows on the door to prevent
injury during airbag deployment.
76) Never lean your head, arms and elbows out of the window.
77) If the
warning light does not
switch on when the key is turned
to MAR-ON, or stays on while
driving (on some versions
together with a message on the
display) there may be a fault in the
restraint systems. In this case,
airbags or pretensioners may not
be activated in the case of an
accident or (in a lesser number of
cases) they may be activated
incorrectly. Before proceeding,
contact a dedicated Alfa Romeo
Dealership to have the system
checked immediately.
78) Do not travel carrying objects on your lap, in front of your chest or
between your lips (pipe, pencils,
etc.): they could cause severe
injury if the airbag is deployed.
72
A0L0056
98
SAFETY
24-9-2013 11:50 Pagina 98

79) If the car has been subject totheft, attempted theft, vandalism,
or flooding, have the airbag
system inspected at a dedicated
Alfa Romeo Dealership.
80) The airbags may also be deployed when the car is not
moving, if the key is inserted and
turned to MAR-ON even when
the engine is off, if the car is hit by
another moving vehicle. Also
remember that no safety device
(airbags or pretensioners) will
activate in the event of impact
when the key is at STOP.
Non-deployment of these devices
under these circumstances does
not therefore indicate a system
malfunction.
81) When the ignition key is turned to MAR-ON, the
warning light
comes on constantly for the first 4
seconds. Then, if the warning
light remains on, this means the
passenger's protection has been
deactivated; if the warning light
switches off, instead, the
passenger's protection is enabled.
82) The front airbag is designed to be deployed for impacts of
a greater intensity than for the
pretensioners. For impacts whose
intensity falls between the two
levels, normally, only the
pretensioners will be activated. 83) The airbag does not replace seat
belts but increases their
effectiveness. Because front
airbags are not deployed for
low-speed frontal impacts, side
collisions, rear shunts or rollovers,
occupants are protected only by
their seat belts, which must
always be fastened.
99
24-9-2013 11:50 Pagina 99

STARTING THE
ENGINEProcedure
84) 85) 86)
❒press the brake pedal;
❒ turn the ignition key to AVV and
release it as soon as the engine
starts.
IMPORTANT INFORMATION
8) 9)
❒ If the engine does not start at the first
attempt, return the ignition key to
STOP before repeating the
procedure.
❒ If, when the ignition key is at
MAR-ON, the
instrument panel
warning light stays on together with
the
warning light, turn the key
to STOP and then back to MAR-ON;
if the warning light stays on, try the
other keys provided with the vehicle.
If it is still not possible to start the
engine, contact a dedicated Alfa
Romeo Dealership.
❒ Do not leave the ignition key at
MAR-ON when the engine is
stopped. WARMING UP THE
ENGINE JUST AFTER IT
HAS STARTED
Procedure
❒
drive off slowly, letting the engine turn
at medium revs. Do not accelerate
abruptly;
❒ do not demand full performance at
first. It is advisable to wait until the
digital engine coolant temperature
indicator starts moving.
SWITCHING OFF THE
ENGINE
Procedure
Turn the ignition key to STOP while the
engine is idling.
10)
IMPORTANT After a demanding drive,
keep the engine idling for at least a
couple of minutes before stopping it, in
order to permit the temperature inside
the engine compartment to lower.
WARNING
84) It is dangerous to run the engine in enclosed areas. The engine
takes in oxygen and releases
carbon dioxide, carbon monoxide
and other toxic gases.
85) The brake servo is not active until the engine is started, so
you would need to apply much
more force than usual to the
brake pedal.
86) Do not start the engine by pushing, towing or driving
downhill. These manoeuvres may
damage the catalytic converter.
IMPORTANT
8) It is advisable not to demandmaximum performance from your
car (e.g. excessive acceleration,
long distances at maximum rpm,
excessively intense braking, etc.)
when it is first used.
102
STARTING AND DRIVING
24-9-2013 11:50 Pagina 102

9) When the engine is off, do notleave the ignition key turned to
MAR-ON to prevent unnecessary
electrical consumption from
draining the battery.
10) A quick burst on the accelerator before turning off the engine
serves absolutely no practical
purpose; it wastes fuel and is
especially damaging to
turbocharged engines.
PARKINGAlways remove the ignition key when
leaving the car.
When parking and leaving the car,
proceed as follows:
❒engage a gear (first gear if parked
uphill or reverse if facing downhill)
and leave the wheels turned;
❒ stop the engine and engage the
handbrake.
Block the wheels with a wedge or a
stone if the car is parked on a steep
slope.
Wait until the indication of the gear
engaged disappears on the display
before releasing the brake pedal.
87)
IMPORTANT: NEVERleave the car with
the gearbox in neutral.
HANDBRAKE
To engage it, pull lever A fig. 73
upwards until the car is secured. When
the handbrake is engaged and the
ignition key is at MAR-ON, the
warning light will switch on in the
instrument panel.
To release the handbrake, raise lever A
slightly, hold down button B and lower
the lever. The
warning light in the
instrument panel will switch off. Four or five clicks are generally enough
when the car is on level ground, while
ten or eleven may be required if the car
is on a steep slope and laden.
88)
IMPORTANT Carry out these
manoeuvres with the brake pedal
pressed.
WARNING
87) Never leave children unattended
in the car. Always remove the key
from the ignition device when
leaving the car and take it with
you.73
A0L0066
103
24-9-2013 11:50 Pagina 103

LEVERS ON THE
STEERING WHEEL
These enable sequential gear shifting
fig. 77.
– steering wheel stalk "+(pulling stalk
towards driver, see fig. 78): engage
higher gear;
– steering wheel stalk "– (pulling stalk
towards driver, see fig. 78): engage
lower gear. The engagement of a lower (or higher)
gear is only permitted if the engine
rpm allow it.
STARTING THE CAR
To start the engine press the brake
pedal: the system engages neutral (N)
automatically.
After the starting procedure, 1st gear
(1) or reverse (R) can be engaged.
Irrespective of the mode selected
(AUTO/MANUAL), to engage 1st gear
or reverse (R), it is necessary to press
the brake pedal and press the
1button
on the transmission control panel (or
the "+" steering wheel stalk) to engage
1st gear or the Rbutton to engage
reverse.
When 1st gear is engaged, the system
sets itself to AUTOmode.
Neutral (N) can be engaged again by
pressing the Nbutton with the brake
pedal pressed.
When the 1,Nor Rbuttons are
pressed (or "+" steering wheel stalk is
operated) without pressing the brake
pedal, no gear change request is
implemented by the system.
IMPORTANT Reverse cannot be
engaged by pressing the "-" stalk on
the steering wheel. Important information
If starting is requested with a
transmission failure (see "Warning lights
and messages" paragraph), carry out
the “Delayed start-up” procedure: when
the key is turned to AVV for at least 7
seconds with brake pedal pressed, the
engine will be started. The system will
remain in “recovery” condition.
If the engine does not start, contact a
dedicated Alfa Romeo Dealership.
When the driver's door is opened, the
system activates the hydraulic
components so that they are prepared
for the subsequent engine starting.
MOVING THE CAR
The car can set off both in 1st gear and
reverse (R).
Notes (concerning car
start-up)
The gears can only be engaged by
pressing the brake pedal. If the brake
pedal is not depressed, the display will
show a dedicated message.
It is not possible to set off in a higher
gear than 1st: if this is attempted,
the display shows a dedicated
message.77
A0L0071
78
A0L0072
106
STARTING AND DRIVING
24-9-2013 11:50 Pagina 106

SNOW TYRESUse snow tyres of the same size as the
normal tyres provided with the car:
the dedicated Alfa Romeo Dealership
will be able to advise you on the most
appropriate tyre to use.
Only use these tyres in the event of ice
or snow on the roads.
For the type of tyre to be used, inflation
pressures and the specifications of
snow tyres, follow the instructions given
in the "Wheels" paragraph in the
"Technical specifications" chapter.
90)
The performance of these tyres on
low-grip surfaces are reduced
considerably when the tread depth is
below 4 mm. They should be replaced
in this case.
Due to the specific characteristics of
snow tyres, in normal weather
conditions or on long motorway
journeys, the performance of these
tyres is lower than that of standard
tyres. Their usage should therefore be
restricted in accordance with their
type approval.IMPORTANT When using snow tyres
with a maximum speed index below the
one that can be reached by the car
(increased by 5%), place a notice in the
passenger compartment, plainly in
view, which states the maximum speed
allowed by the snow tyres (as per EC
Directive).
All four tyres should be the same brand
to ensure greater safety when driving
and braking as well as making the
car more responsive. It is inadvisable to
change the rotation direction of tyres.
Refer to the "Raising the car" section in
the "In an emergency" chapter for
further details on how to raise the car
correctly.
WARNING
90) The maximum speed for snow
tyres marked “Q” is 160 km/h,
while it is 190 km/h for “T” tyres
and 210 km/h for "H" tyres. The
highway code speed limits must
however always be complied with.
CAR INACTIVITYIf the car is to be left inactive for longer
than a month, observe the following
precautions:
❒park the car in covered, dry and if
possible well-ventilated premises and
slightly open the windows;
❒ check that the handbrake is not
engaged;
❒ disconnect the negative battery
terminal and check the battery
charge. Repeat this check once
every three months during storage.
For optimum preservation of the
battery charge, it is advisable to use
the charge-holder (for versions/
markets, where provided, or
alternatively, available from
Lineaccessori). For more details on
its operation, refer to the attached
Supplement;
❒ if the battery is not disconnected
from the electrical system, checks its
state of charge every thirty days;
❒ clean and protect the painted parts
using protective wax;
111
24-9-2013 11:50 Pagina 111