buttons Alfa Romeo 4C 2016 Owner handbook (in English)

AIR VENTSClimate control.................. 22
LEFT STALKExternal lights................... 28
INSTRUMENT PANELControl panel and on-board
instruments....................... 58
Warning lights................... 67
RIGHT STALKWindow cleaning................ 29
PASSENGER-SIDE AIR BAGOperation....................... 90
DASHBOARD CONTROLSRear fog light................... 32Central locking.................. 32Door mirror demisting........... 28
HEATER/CLIMATE CONTROL
SYSTEM
Climatic comfort................ 23Heating and ventilation.......... 24Manual climate control.......... 26
STEERING WHEELAdjustment..................... 20
Driver's side front airbag......... 90
CONTROL BUTTONSSetup menu.................... 60Menu options................... 61
3A0L0144
11

the dashboard;
press thebutton on the key or the
door locking/unlocking button on
the dashboard.
ELECTRIC WINDOWS
These operate when the ignition key is
turned to MAR-ON and for about three
minutes after the ignition key is turned
to STOP or removed unless one of the
doors is opened.
The buttons are located on the central
tunnel.
20)
Operation
A - Open/close left window;
B - Open/close right window;
Push the corresponding buttons to
open/close the desired window.
When one of the two buttons is
pressed briefly, the window moves in
stages; if the button is held down to
open, "continuous automatic" operation
is activated.
If the button is pressed again thewindow will stop in its current position.
If the button is pressed for several
seconds, the window lowers
automatically (only with ignition key in
MAR-ON position).
Continuous automatic operation
(for versions/markets, where provided)
This is activated by pressing one of the
two buttons for longer than half a
second. The window stops when it
reaches the end of travel position, or
when the button is pressed again.
It can be used on both the driver side
and passenger side, only for lowering
the window.
Electric window system
initialisation
For versions/markets where provided,
after a break in power supply for the
control units (battery replaced or
disconnected or protective fuses for the
electric window control units replaced),
the automatic operation of the windows
must be restored.
The restoration procedure must be
performed as described below with the
doors closed:
completely open the driver's door
window keeping the operating button
pressed for at least three seconds after
the (lower) end of travel position is
reached;
completely raise the driver side
window and hold the button down for
at least 3 seconds once the (upper) end
40A0L0002
37

SPEEDOMETER (SPEED
INDICATOR)
Indicator J shows the speed of the car.
REV COUNTER
Light C shows the engine revs.
FUEL LEVEL GAUGE
Gauge G shows the amount of fuel in
the tank.
The switching on of the
digital
warning light indicates that 4–5 litres of
fuel are left in the tank; in this situation,
refuel as soon as possible.
Do not travel with the fuel tank almost
empty: any gaps in fuel delivery could
damage the catalytic converter.
ENGINE COOLANT
TEMPERATURE
INDICATOR
Indicator A shows the temperature of
the engine coolant and starts supplying
indications when the fluid temperature
exceeds approximately 50°C.
The
digital warning light may switch
on (together with a message on the
display) to indicate that the coolant
temperature is too high; in this case,
stop the engine and contact a
dedicated Alfa Romeo Dealership.
GEAR SHIFT INDICATOR
The GSI (Gear Shift Indicator) system
advises the driver to change gear
through a specific indication E fig. 59 on
the instrument panel.Through the GSI, the driver is notified
that changing gear will allow a reduction
in fuel consumption.
Therefore, for driving oriented towards
reducing fuel consumption, it is
advisable to stick to “Natural” or “All
Weather” mode and to follow the
suggestions of the Gear Shift Indicator,
where traffic conditions permit.
When the (
) icon is displayed on the
instrument panel, the GSI suggests
switching to a higher gear, while when
the (
) icon is displayed, the GSI
suggests changing to a lower gear.
IMPORTANT The GSI is not active
when the transmission is operating in
AUTO mode.
IMPORTANT The indication in the
instrument panel remains on until the
driver shifts gear or the driving
conditions go back to a situation where
gearshifting is not required to improve
consumption.
SETUP MENU
CONTROL BUTTONS
SET/: press briefly to access the
menu and/or go to next screen or
confirm the selection. Hold down to
return to the standard screen fig. 61.
: to scroll up through the displayed
screen and the related options or to
increase the displayed value.
: to scroll down through the
displayed menu and the related options
or to decrease the value displayed.
IMPORTANT The
andbuttons
activate different functions according to
the following situations:
within the menu, they allow you to
scroll up and down through the options;
during setting operations, they
increase or decrease the displayed
value;
outside of the menu, they permit the
61A0L0125
60
KNOWING THE INSTRUMENT PANEL

adjustment of the control panel
brightness.
MENU
The menu comprises a series of options
which can be selected using theandbuttons to access the different
selection and setting (Setup) operations
indicated below.
Some options have a submenu. The
menu can be activated by briefly
pressing the SET/
button.
The menu comprises the following
options:
MENU
SPEED BEEP
TRIP B ACTIVATION/DATA
SET TIME
SET DATE
AUTOCLOSE (for versions/markets,
where provided)
MEASUREMENT UNIT
LANGUAGE
BUZZER VOLUME
BELT BUZZER/BEEP (may only be
displayed after the SBR system is
deactivated by the dedicated Alfa
Romeo Dealership)
SERVICE
AIRBAG/PASSENGER BAG
DAYTIME RUNNING LIGHTS (for
versions/markets, where provided)
EXIT MENU
Selecting an option from
the main menu without a
submenu:
press the SET/button briefly to
select the main menu setting you wish
to change;
press buttonsor(with single
presses) to select the new setting;
press the SET/button briefly to
save the new setting and go back to
the previous main menu option.
Selecting an option from
the main menu with a
submenu:
briefly press the SET/button to
display the first submenu option;
press buttonsor(with single
presses) to scroll through all the
submenu options;
briefly press the SET/button to
select the displayed submenu option
and to open the relevant settings menu;
press buttonsor(with single
presses) to select a new setting for this
submenu option;
press the SET/button briefly to
save the new setting and go back to
the previous submenu option.
MENU OPTIONS
Menu
This option allows you to access the
Setup Menu.
Press the
orbutton to select the
various Menu options. Hold down the
SET/
button to return to the
standard screen.
Speed warning (Speed
limit)
With this function is possible to set the
car speed limit ("km/h" or "mph"); when
this limit is exceeded the driver is
alerted.
To set the desired speed limit, proceed
as follows:
briefly press the SET/button,
the display will show the wording
"Speed warning";
press buttonorto select
speed limit activation ("On") or
deactivation ("Off");
if the function is on, pressorto
select the desired speed limit and then
press SET/
to confirm.
IMPORTANT Setting is possible
between 30 and 200 km/h, or 20 and
125 mph, according to the previously
set unit. See the "Measurement unit
(Measurement unit adjustment)"
paragraph described below. The setting
will increase/decrease by 5 units each
time button
/is pressed. Hold
61

button down to go back to the
standard screen without saving.
Warnings volume
(Adjusting the failure/
warning buzzer volume)
With this function the volume of the
buzzer which accompanies the display
of failure/warning can be adjusted
according to 8 levels.
To set the desired volume proceed as
follows:
press button SET/briefly. The
volume “level” set previously flashes on
the display;
press theorbutton to make
the adjustment;
briefly press the SET/button to
go back to the menu screen or hold the
button down to go back to the
standard screen without saving.
Belt reminder (Buzzer
reactivation for SBR
indication)
(for versions/markets, where provided)
This function can be displayed only
after a dedicated Alfa Romeo
Dealership has deactivated the SBR
system (see "SBR system" paragraph in
the "Safety" chapter).
Service (Scheduled
servicing)
Using this function you can display
information about the mileage intervals
for vehicle servicing.
To consult this information, proceed as
follows:
press button SET/briefly. The
display shows the service interval in
kilometres (km) or miles (mi) according
to the previous setting (see the "Unit of
measurement (Setting the unit of
measurement)" paragraph);
briefly press the SET/button to
go back to the menu screen or hold the
button down to go back to the
standard screen.
IMPORTANT The “Scheduled Servicing
Plan” includes car maintenance at fixed
intervals, refer to the "Maintenance and
care" chapter. The "Service" function is
automatically displayed, along with the
warning light coming on, with key at
MAR-ON - starting from 2,000 km (or
equivalent value in miles) before these
deadlines and is activated again every
200 km (or equivalent value in miles).
Below 200 km servicing indications are
more frequent. The indication will
appear in kilometres or miles according
to the "Unit of measurement" settings.
In addition, when the vehicle mileage is
close to a scheduled servicing ("service
coupon"), and the key is turned to
MAR-ON, the
warning light willappear on the display along with the
word "Service" and followed by the
number of kilometres or miles left
before vehicle servicing. Contact a
dedicated Alfa Romeo Dealership. The
operations in the “Scheduled Servicing
Plan” will be performed and the
message will be reset.
Passenger airbags
(Activation/Deactivation
of passenger's side
front airbag)
This function is used to activate/
deactivate the front passenger's airbag.
Proceed as follows:
press the SET/button and, after
the message (Bag pass: Off) (to
deactivate) or (Bag pass: On) (to
activate) is displayed by pressing
buttons "
"or"", press the SET/
button again;
a confirmation request message will
appear on the display;
by pressing theorbuttons
select "Yes" (to confirm activation/
deactivation) or "No" (to cancel);
press the SET/button briefly, a
message confirming the selection will
be displayed and you will go back to
the menu screen, or hold the button
down to go back to the standard
screen without saving. The warning
light
in the instrument panel
switches on.
64
KNOWING THE INSTRUMENT PANEL

PARKING
Always remove the ignition key when
leaving the car.
When parking and leaving the car,
proceed as follows:
engage a gear (first gear if parked
uphill or reverse if facing downhill) and
leave the wheels turned;
stop the engine and engage the
handbrake.
Block the wheels with a wedge or a
stone if the car is parked on a steep
slope.
Wait until the indication of the gear
engaged disappears on the display
before releasing the brake pedal.
87)
IMPORTANT:NEVERleave the car with
the gearbox in neutral.
HANDBRAKE
To engage it, pull lever A
fig. 75 upwards until the car is secured.
When the handbrake is engaged and
the ignition key is at MAR-ON, the
warning light will switch on in the
instrument panel.
To release the handbrake, raise lever A
slightly, hold down button B and lower
the lever. The
warning light in the
instrument panel will switch off.
Four or five clicks are generally enough
when the car is on level ground, while
ten or eleven may be required if the car
is on a steep slope and laden.
88)
IMPORTANT Carry out these
manoeuvres with the brake pedal
pressed.
WARNING
87)Never leave children unattended in the
car. Always remove the key from the
ignition when leaving the car and take it
with you.
88)The car must be locked after a few
clicks of the parking brake: if this is not so,
contact the dedicated Alfa Romeo
Dealership to have it adjusted. Always park
the vehicle safely as indicated by the
Highway Code and as described above.
USING THE
TRANSMISSION
The 4C features the TCT 6-speed twin
dry clutch transmission with steering
wheel controls. This is an advanced
technical solution which combines the
control of a manual gearbox, the
immediacy of a sequential system and
the convenience of being able to select
an automatic selection programme
without the slowdown of a conventional
automatic transmission.
With the key removed from the ignition,
the system will not implement any
action when the buttons on the
transmission control panel on the
central tunnel fig. 76 are pressed,
irrespective of the pressure applied to
the brake pedal. Therefore, the
transmission will remain in the condition
that it was in when the engine was
switched off.
75A0L0066
76A0L0067
96
STARTING AND DRIVING

suitable power and torque for the
acceleration requested by the driver.
When implementing the "Kick Down"
function, the system ensures varying
transmission management in
accordance with the selected DNA
mode.
LEVERS ON THE
STEERING WHEEL
These enable sequential gear shifting
fig. 79.
– steering wheel stalk "+(pulling stalk
towards driver, see fig. 80 ): engage
higher gear;
– steering wheel stalk "–(pulling stalk
towards driver, see fig. 80 ): engage
lower gear.The engagement of a lower (or higher)
gear is only permitted if the engine rpm
allow it.
STARTING THE CAR
To start the engine press the brake
pedal: the system engages neutral (N)
automatically.
After the starting procedure, 1st gear (
1) or reverse (R) can be engaged.
Irrespective of the mode selected (
AUTO/MANUAL), to engage 1st gear
or reverse (R), it is necessary to press
the brake pedal and press the1button
on the transmission control panel (or
the "+" steering wheel stalk) to engage
1st gear or theRbutton to engage
reverse.
When 1st gear is engaged, the system
sets itself toAUTOmode.
Neutral (N) can be engaged again by
pressing theNbutton with the brake
pedal pressed.When the1,NorRbuttons are
pressed (or "+" steering wheel stalk is
operated) without pressing the brake
pedal, no gear change request is
implemented by the system.
IMPORTANT Reverse cannot be
engaged by pressing the "-" stalk on
the steering wheel.
Important information
If starting is requested with a
transmission failure (see "Warning lights
and messages" paragraph), carry out
the “Delayed start-up” procedure: when
the key is turned to AVV for at least 7
seconds with brake pedal pressed, the
engine will be started. The system will
remain in “recovery” condition.
If the engine does not start, contact a
dedicated Alfa Romeo Dealership.
When the driver's door is opened, the
system activates the hydraulic
components so that they are prepared
for the subsequent engine starting.
MOVING THE CAR
The car can set off both in 1st gear and
reverse (R).
Notes (concerning car start-up)
The gears can only be engaged by
pressing the brake pedal. If the brake
pedal is not depressed, the display will
show a dedicated message.
It is not possible to set off in a higher
gear than 1st: if this is attempted, the
display shows a dedicated message.
79A0L0071
80A0L0072
98
STARTING AND DRIVING

INDEX
"Alfa DNA" system............44
"All Weather" mode..........45
"Natural" mode............44
“Dynamic” mode...........44
“Race” mode..............45
Driving modes.............44
"Electronic Q2" system ("E-Q2")....42
"Follow Me Home" device........29
ABS.....................41
System intervention..........41
Accessories purchased by the
owner....................5
Air cleaner.................137
Alarm.....................16
Alfa Romeo Code system........14
Alzacristalli elettrici
Funzionamento............37
Ashtray....................35
ASR system (AntiSlip Regulation) . . .42
Backrest pocket.............35
Battery...................138
advice for extending lifetime. . . .138
replacement..............138
Battery (recharging)...........124
Body
body codes..............148
Bodywork
maintenance.............141protection against atmospheric
agents.................141
warranty................141
Bodywork versions...........148
Brakes...................152
brake fluid level............135
bulb replacement.........117 ,118
Bulb replacement
exterior lights.............116
interior lights.............119
Bulbs
types of bulbs............114
Car inactivity...............103
Carrying children safely..........86
CBC (Cornering Brake Control)
system..................41
Central locking...............32
Changing a bulb.............112
General instructions.........112
Changing a wheel............109
Cigar lighter.................34
Cleaning and maintenance
bodywork...............141
car interior...............143
engine compartment........142
front headlights............142
leather parts.............143
leather seats.............143
plastic and coated parts......143seats and fabric parts........143
windows................142
Climate control...............22
Passenger compartment air
diffusers.................23
Climatic comfort..............23
Clutch...................151
CO2 emissions..............167
Conditions of use............101
Control buttons..............60
Control panel and instruments.....58
Controls...................32
Cruise Control...............30
Cup holder.................35
Daytime running lights (DRL)......28
Diffusori aria laterali............22
Dimensions................159
Dipped beam headlights
bulb replacement..........116
Dipped headlights
bulb replacement..........116
Direction indicators............29
“Lane change” function.......29
bulb replacement..........116
Door mirrors
Door mirrors..............20
Doors.....................36
Central door locking/unlocking . . .36