wiper blades Alfa Romeo 4C 2016 Owner handbook (in English)
[x] Cancel search | Manufacturer: ALFA ROMEO, Model Year: 2016, Model line: 4C, Model: Alfa Romeo 4C 2016Pages: 182, PDF Size: 9.49 MB
Page 33 of 182
screen wiper will be stopped
automatically.
With ring nut A fig. 23 in
position,
the screen wiper will automatically
adapt its operating speed to the speed
of the car.
"Smart washing" function
Pull the stalk towards the steering
wheel (unstable position) to operate the
screen washer. Keeping the stalk pulled
for more than half a second, with just
one movement it is possible to operate
the screen washer jet and the wiper at
the same time.
The wiper stops working three strokes
after the stalk is released. A further
stroke after approximately 6 seconds
completes the cycle.
WARNING
12)Never use the windscreen wipers to
remove layers of snow or ice from the
windscreen. In such conditions, the
windscreen wiper may be subjected to
excessive stress and the motor cut-out
switch, which prevents operation for a few
seconds, may intervene. If operation is not
restored (even after restarting that car with
the key), contact a dedicated Alfa Romeo
Dealership.
13)Do not operate the screen wiper with
the blades lifted from the windscreen.
CRUISE CONTROL
(for versions/markets, where provided)
This is an electronically controlled
driving assistance device that allows the
desired car speed to be maintained,
without having to press the accelerator
pedal. This device can be used at a
speed above 30 km/h on long stretches
of dry, straight roads with few variations
(e.g. motorways).
It is therefore not recommended to use
this device on extra-urban roads with
traffic. Do not use it in town.
Activation
Turn ring nut A fig. 24 to.
The device cannot be engaged in 1st or
reverse gear: it is advisable to engage it
in 5th gear or higher.
When travelling downhill with the device
engaged, the car may slightly exceed
the stored speed.When the device is activated, the
digital warning light switches on
together with the relevant message on
the display.
Storing speed
Proceed as follows:turn ring nut A fig. 24 toand
press the accelerator to reach the
desired speed;
move the stalk upwards (+) for at
least 1 second, then release it: the car
speed is now stored and you can
therefore release the accelerator.
If needed (when overtaking for
instance), you can accelerate simply by
pressing the accelerator; when you
release the pedal, the car goes back to
the speed stored previously.
Restoring speed
If the device has been deactivated, for
example by pressing the brake pedal,
the stored speed can be restored as
follows:
accelerate gradually until a speed
approaching the one stored is reached;
engage the gear selected at the time
that the speed was stored;
press the CANCEL/RESUME button
(B fig. 24 ).24A0L0022
30
GETTING TO KNOW YOUR CAR
Page 144 of 182
Replacing the
windscreen wiper blade
Proceed as follows:lift the windscreen wiper blade,
following the instructions given
preciously;
press tab A fig. 133 of the
attachment spring and remove the
blade from the arm;
fit the new blade, inserting the tab in
the dedicated housing in the arm and
checking that it is locked;
lower the wiper arm onto the
windscreen.
NOZZLES
Screen washer
The windscreen washer nozzles are
adjustable fig. 134. They are originally
adjusted at the factory. Should it be
necessary to adjust them again,
contact a dedicated Alfa RomeoDealership.
If there is no jet of fluid, firstly check that
there is some fluid in the reservoir (see
paragraph "Checking fluid levels" in this
chapter).
Then check that the nozzle holes are
not clogged; use a needle to unblock
them if necessary.
WARNING
136)Driving with a worn wiper blade is a
serious hazard, because visibility is
reduced in bad weather.
IMPORTANT
29)Do not operate the screen wiper with
the blades lifted from the windscreen.
BODYWORK
PROTECTION AGAINST
ATMOSPHERIC AGENTS
The car features advanced
technological solutions for effective
protection of the exterior bodywork and
structure.
The best products and best painting
systems lend the exterior bodywork
particularly high resistance to
atmospheric agents (solar radiation,
acid rain, etc.) and gravel, through
specific protections.
The chassis too, in light,
corrosion-resistant alloy, is treated to
prevent the formation of surface
oxidation.
CAR CORROSION
WARRANTY
Your car is covered by warranty against
perforation, due to rust, of any original
element of the structure. For the
general terms of this warranty, refer to
the Warranty Booklet.
PRESERVING THE
BODYWORK
Paintwork5)30)
Touch up abrasions and scratches
immediately.
Maintenance of paintwork consists of
washing the car: the frequency
depends on the conditions and
environment where the car is used. For
example, in highly polluted areas, or if
133A0L0086
134A0L0087
141
31)
Page 181 of 182
inflation pressures..........158
reading the tyre code........155
snow tyres...............157
tyres provided............157
Tyres - maintenance...........139
Using the transmission.........96
Warning lights and messages.....67
Weights..................161Wheel rims
reading the rim code........155
Wheels and tyres
changing a wheel..........109
Fix&Go automatic (kit).......106
tyre inflation pressure........158
Wheel repair.............106Wheels and tyres..........139
Window cleaning.............29
Windows (cleaning)...........142
Windscreen washer nozzles......141
Windscreen wiper
blades.................140
replacing blades...........141
INDEX
MOPAR
TECHNICAL SERVICES - SERVICE ENGINEERING
FCA Italy S.p.A. - Largo Senatore G. Agnelli, 3 - 10040 Volvera - Torino (Italia)
Print No. 530.05. 53 - 1 Edition - /2015
All rights reserved. Reproduction, even partial, without written authorisation
from FCA Italy S.p.A. is prohibited12 0