roof Alfa Romeo 4C 2017 Owner's Manual
[x] Cancel search | Manufacturer: ALFA ROMEO, Model Year: 2017, Model line: 4C, Model: Alfa Romeo 4C 2017Pages: 289, PDF Size: 2.61 MB
Page 17 of 289
NOTE:The line of transmission must not be blocked
with metal objects.
To Unlock The Doors
Push and release the UNLOCK buttonon the Key
Fob to unlock the doors. The park lights and turn
signal lights will flash to acknowledge the signal and
the illuminated entry system will turn on.
NOTE: The Door Unlock Indicator will illuminate in
the instrument panel when one or both doors are
unlocked.
To Lock The Doors
Push and release the LOCKbutton on the Key Fob
will lock the doors, switching off the internal roof
light and single flashing of direction indicators.
If one or more doors are open, the doors will not be
locked. This is indicated by a rapid flashing of the
direction indicators. The doors will be locked if the
decklid is open however.
When a speed of more than 12 MPH (20 km/h) is
reached, the doors will be locked automatically if the
Autoclose function was selected. Refer to “Instrument
Cluster Display” in “Understanding Your Instrument
Panel” for further information.
Key Fob
1 — Vehicle Key
2 — Push To Open/Close Vehicle Key
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
Page 210 of 289
VEHICLE STORAGE ...................244
REPLACEMENT BULBS ................245
BULB REPLACEMENT .................246
▫ Front Light Clusters ..................246
▫ Front Side Marker ....................250
▫ Rear Light Clusters ...................251
▫ Direction Indicators ..................251
▫ Tail Lights/Brake Lights ...............252
▫ Reversing Light .....................252 ▫
Third Brake Lights ...................253
▫ License Plate Lights ..................253
▫ Roof Light ........................ .254
▫ Luggage Compartment Roof Light ........255
FLUID CAPACITIES ...................256
FLUIDS, LUBRICANTS, AND
GENUINE PARTS .....................257
▫ Engine ........................... .257
▫ Chassis .......................... .258
208 MAINTAINING YOUR VEHICLE
Page 256 of 289
2. Turn bulb holder (1) counterclockwise, remove bulb(2) and replace it.
Roof Light
To change the bulb, proceed as follows:
1. Remove roof light working at the points indicated bythe arrows. 2. Open protective flap (2) and replace bulb (1), releas-
ing it from the side contacts. Make sure that the new
bulb is correctly secured between the contacts.
1 — Bulb Holder
2 — Bulb
Roof Light
254 MAINTAINING YOUR VEHICLE
Page 257 of 289
3. Close protective flap (2) and install roof light in itshousing, making sure that it is locked in place.
Luggage Compartment Roof Light
To replace the bulb, proceed as follows:
1. Open the luggage compartment and remove luggagecompartment roof light, working in the direction
shown by the arrow. 2. Open light protector (2) and replace the bulb.
3. Close protector on the lens.
4. Install luggage compartment roof light by inserting it
in its correct position, first on one side and then
pressing on the other side until it clicks into place.
1 — Bulb
2 — Protective Flap
1 — Light Cover
2 — Light Protector
7
MAINTAINING YOUR VEHICLE 255
Page 288 of 289
INSTALLATION OF RADIO TRANSMITTING
EQUIPMENTSpecial design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.
The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect the accuracy or operation of the compass on
vehicles so equipped.The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.