four wheel drive Alfa Romeo 4C 2020 Owner handbook (in English)

51
ESC SYSTEM
The ESC system improves the
directional control and stability of the
car in various driving conditions.
The ESC system corrects the car’s
understeer and oversteer, distributing
the brake force on the appropriate
wheels. The torque supplied by the
engine can also be reduced in order to
maintain control of the vehicle.
25) 26) 27) 28) 29)
The ESC system comprises the active
safety systems such as: ABS, EBD, ASR,
HILL HOLDER, etc.
The ESC system switches on
automatically when the engine is started
and cannot be switched off.
System intervention
This is indicated by the flashing of the
warning light on the instrument panel, to
inform the driver that the car is in critical
stability and grip conditions.
CBC
(Cornering Braking Control) SYSTEM
This system acts when braking on
corners, optimising the distribution of
brake pressure on the four wheels: the
system prevents the wheels on the
inside of the corner (less affected by the
weight of the car) from locking, ensuring
better stability and direction for the car.
HILL HOLDER SYSTEM
This is an integral part of the ESC system
and facilitates starting on uphill or
downhill slopes by operating the brakes:
IMPORTANT The Hill Holder system is
not a parking brake, therefore do not
leave the car without activating the
handbrake, switched the engine off and
engaged first gear, so that the car is
parked in safety conditions (for further
information read paragraph
“When parked” in the chapter “Starting
and driving”).
IMPORTANT There may be situations on
small gradients (less than 8%), with car
laden, in which the Hill Holder system
may not activate thus causing a slight
reversing motion and increasing the risk
of collision with another vehicle or
object. The driver is, in any case,
responsible for safe driving.
“ELECTRONIC Q2” SYSTEM (“E-Q2”)
The DTC system prevents the drive
wheels from possibly locking, which
could happen, for example, if the
accelerator pedal is released suddenly or
in the case of a sudden downshifting in
conditions of poor grip.
In this conditions, the engine braking
effect could cause the drive wheels to
slip, resulting in a loss of vehicle stability.
In these situations, the DTC system
intervenes, restoring torque to the
engine in order to conserve vehicle
stability and increase vehicle safety.

SAFETY
54 The TPMS uses wireless devices with
electronic sensors mounted on the wheel
rims to constantly monitor the value of
tyre pressure.

The sensors mounted on each wheel as
part of the valve stem transmit various
information of the tyres to the receiver
module, in order to calculate the
pressure.
IMPORTANT Monitoring and maintaining
the correct pressure in all four tyres are
particularly important.
Tyre pressure monitoring system
low pressure warnings
43) 44) 45) 46) 47) 48) 49) 50) 51)
The system warns the driver if one or
more tyres are flat by switching on the
nwarning light constantly and by
displaying a dedicated messages.
In this case, stop the car as soon as
possible, check the inflation pressure of
each tyre and inflate to the cold tyre
pressure value prescribed for the car.
The system will automatically update
and after receiving the pressure update
the tyre pressure warning light switches
off.
You may need to drive the car for about
20 minutes at a speed higher than 20
km/h to allow the system to receive this
information.
32A0L0113
TPMS operation faults
The system fault is indicated by the
dedicated warning light
nwhich first
flashes for 75 seconds and then stays on
steadily. This can occur in any of the
following situations:
❒ Interference caused by electronic
devices or radio frequency emissions
similar to those of the TPMS sensors.
❒ Application of tinted films which
interfere with the signals of the radio
waves.
❒ Presence of snow or ice on the wheels
or the wheel arches.
❒ Use of snow chains.
❒ Use of wheels/tyres not equipped
with TPMS sensors.