jack points Alfa Romeo 4C 2020 Owner handbook (in English)

91
❒ insert the operating rod 3 fig. 72 in
the housing on the device 1 fig. 71;
71A0L0184
72A0L0186
❒ push the jack under the car using the
rod until the wording “STOP” on the rod
corresponds with the side skirt:
“FRONT” when replacing the front wheel,
“REAR” when replacing the rear wheel
(see fig. 73, 74 );
❒ fit the suitable tool 4 in Fig. 72 on the
operating rod;
IMPORTANT As shown in fig. 73,74, on
the operating rod there is the indication
of max. limit for front and rear insertion
under car that must coincide with the 
mark on the side skirts.
73A0L0189
❒ operate the device 1 fig. 71 so as to
extend the jack, until the upper part
2 Fig. 71 rests correctly in one of the
lifting points shown in fig. 75- fig. 76,
otherwise, reposition the jack.
74A0L0190
75A0L0185

IN AN EMERGENCY
92
IMPORTANT Make sure that the upper
part 2 of the jack rests firmly on the
undercarriage of the car in the points
shown in fig. 75, 76 to prevent the car
from falling while it is being jacked up.
100)
❒ operate the jack and lift the car until
the wheel is several
centimetres off the ground;
❒ alert any bystander that the car is
about to be raised; all persons should be
kept away from the car and nobody must
touch it until it has been lowered;
❒ remove the damaged wheel;
76A0L0188
❒ make sure the contact surfaces
between space-saver wheel and hub are
clean and free from impurities so that the
fixing stud bolts will not come loose;
❒ fit the space-saver wheel and tighten
the first stud bolt for a few turns into the
lowest hole. Tighten the remaining stud
bolts in the same way.
❒ take the spanner 1 fig. 70 and fully
tighten the fixing stud bolts;
❒ operate the suitable tool 4 fig. 72 to
lower the car.
Then extract the jack;
❒ using spanner 1 fig. 70 tighten the
stud bolts fully, alternating from a stud
bolt to the diametrically opposite one,
❒ in the numeric order shown in fig. 77.
WARNING While replacing the wheel it is
advisable to place it upside down, with
the aesthetic part facing upward, so as
not to damage the alloy rim.REFITTING THE WHEEL
Following the procedure described
previously, raise the vehicle and remove
the space-saver wheel.
Proceed as follows:
❒ make sure the contact surfaces
between standard wheel and hub are
clean and free from impurities so that the
fixing stud bolts will not come loose;
❒ using the spanner 1 fig. 70 and tighten
the fixing stud bolts;
❒ lower the vehicle and remove the jack;
❒ use spanner 1 to fully tighten the stud
bolts, following the order shown in 77.
101)
77A0L0187

INSPECTING THE CHARGE
AND THE ELECTROLYTE LEVEL
126) 127) 128) 129)
21)
5)
If necessary, replace the battery with
another original battery with the same
specifications. Follow the battery
manufacturer’s instructions for
maintenance.
SERVICING AND CARE
114
126)Battery fluid is poisonous and
corrosive. Avoid contact with the skin and
eyes. Keep open flames away from the
battery and do not use objects that might
create sparks: risk of explosion and
fire.
127)Using the battery with insufficient
fluid irreparably damages the battery
and may cause an explosion.
128)If the car will be unused for an
extended period of time in extremely cold
weather conditions, remove the battery
and store it in a heated area to prevent it
from freezing.
129)Always wear appropriate goggles
when working on or near the battery.
IMPORTANT
21)Incorrect assembly of electrical and
electronic accessories may cause severe
damage to your vehicle. After purchasing
your vehicle, if you wish to install any
accessories (anti-theft, etc.), go to a
dedicated Alfa Romeo Dealership, which
will suggest the most suitable devices and
advise you whether a higher capacity
battery needs to be installed.
WARNING
5)Batteries contain substances which are
very dangerous for the environment. For
battery replacement, contact a dedicated
Alfa Romeo Dealership.
WARNING
RAISING THE CAR
If raising the car is necessary, contact a
dedicated Alfa Romeo Dealership, who
will be equipped with suitable arm or
workshop lifts, in addition to the specific
equipment necessary.
It is however possible to use suitable
lowered hydraulic jacks to raise the car if
necessary.
The car lifting points are marked on the
side skirts with the symbols (see
points illustrated in fig. 100).
100A0L0029

115
The correct support points for raising
the front and rear part of the car are
illustrated in fig. 101 and fig. 102.
IMPORTANT When positioning the car
on the arm lift, remember that the power
unit is located at the rear end, with
consequent impact on weight
distribution. Therefore, the shorter arms
must support the rear end, and the
longer arms support the front end.
22) 23)
101A0L0128
WARNING
102A0L0127
BODYWORK
PROTECTION FROM ATMOSPHERIC
AGENTS
The car features advanced technological
solutions for effective protection of the
exterior bodywork and structure.
The best products and best painting
systems lend the exterior bodywork
particularly high resistance to
atmospheric agents (solar radiation, acid
rain, etc.) and gravel, through specific
protections.
The chassis too, in light,
corrosion-resistant alloy, is treated to
prevent the formation of surface
oxidation.
CAR CORROSION WARRANTY
Your car is covered by warranty against
perforation, due to rust, of any original
element of the structure. For the general
terms of this warranty, refer to the
Warranty Booklet.
22)Be careful to position the lift arms
correctly at the points illustrated, in order
to prevent damage to the carbon fibre
chassis and the bodywork components.
23)To avoid damage to the carbon fibre
chassis, the car cannot be raised with
standard hydraulic jacks, only with
suitable lowered hydraulic jacks.
Contact a dedicated Alfa Romeo
Dealership.