transmission Alfa Romeo 4C 2020 Owner handbook (in English)

KNOWING THE INSTRUMENT PANEL TOOLS
32
DISPLAY
The car is equipped with a display that,
according to the previously applied
settings, will show useful driving
information.
GEAR SHIFT INDICATOR
The GSI (Gear Shift Indicator) system
advises the driver to change gear
through a specific indication 5 fig. 29, 30
on the instrument panel.
Through the GSI, the driver is notified
that the gear change will allow a
reduction in fuel consumption.
Therefore, for driving oriented towards
reducing fuel consumption, it is advisable
to stick to “Natural” or “All Weather”
mode and to follow the suggestions of
the Gear Shift Indicator, where traffic
conditions permit.
When the () icon is displayed on the
instrument panel, the GSI suggests
switching to a higher gear, while when
the () icon is displayed, the GSI
suggests shifting to a lower gear.
IMPORTANT The GSI is not active when
the transmission is operating in AUTO
mode.
The indication in the instrument panel
remains on until the driver shifts gear or
the driving conditions go back to a
situation where gearshifting is not
required to improve consumption.
CONTROL BUTTONS fig. 31
: to scroll up through the displayed
screen and the related options or to
increase the displayed value.
SET/
N: press briefly to access the
menu and/or go to next screen or
confirm the selection. Hold down to go
back to the standard screen
: to scroll down through the displayed
menu and the related options or to
decrease the value displayed.IMPORTANT Buttons and activate
different functions according to the
following situations:
❒ within the menu, they allow you to
scroll up or down through the options;
❒ during setting operations, they
increase or decrease the displayed value;
❒ outside the menu they allow
to adjust the on board panel
brightness.
MAIN MENU
The menu comprises a series of options
which can be selected using the and 
buttons to access the different selection
and setting (Setup) operations indicated
below.
31A0L0125

43
Warning lights on panelMeaningWhat to do
TCT FAULT
The digital warning light switches on when the key is
turned to MAR-ON, but it should switch off after a few
seconds.
The digital warning light flashes (together with a message
in the display and an acoustic signal) to indicate that the
TCT is faulty.
The warning light or symbol switches on in the case of
transmission overheating, after a particularly demanding
use; engine performance is limited in this case.
DOOR OPEN
(where provided)
The digital warning light on the display switches on when
one or more doors are not properly shut. A buzzer will
sound when doors/tailgate are open and the car is moving.
BRAKE PAD WEAR
(where provided)
The digital warning light switches on when the front or
rear brake pads show signs of wear.
The associated message appears on the display.Replace the pad as soon as possible.
ALFA ROMEO CODE SYSTEM FAULT
(where provided)
The digital warning light (or symbol on the display) will
come on (on some versions, with a message on the
display) to indicate an Alfa Romeo CODE system or alarm
fault.Contact a dedicated
Alfa Romeo Dealership as soon as possible.
Contact a dedicated
Alfa Romeo Dealership as soon as possible.
If you need to start the engine in presence of a faulty
gearbox, follow the procedure shown in the
“TCT twin clutch transmission”, paragraph in the “Starting
the engine” section, “Starting and driving” chapter.

KNOWING THE INSTRUMENT PANEL TOOLS
46
Warning lights on panelMeaningWhat to do
GENERIC FAILURE INDICATION
(where provided)
The symbol appears on the display together with the
events shown below.
Engine oil pressure sensor
The symbol appears when a failure is detected in the
engine oil pressure sensor. The display shows the
dedicated message.In this case, go to a dedicated
Alfa Romeo Dealership as soon as possible to have the
fault corrected.
Clutch overheating message
The
symbol, together with a message on the display,
lights up to indicate clutch overheating.
If you continue driving, the symbol
will disappear and
the warning light will come on (on some versions
together with a message on the display) to indicate a
gearbox fault.
If the symbol comes on together with a message on
the display, limit the gear shifting and/or change the
condition of use, until normal operating conditions are
restored.
If the warning light lights up (a message will appear on
the display, on some versions) stop immediately, operate
the handbrake, switch off the engine and wait 5 minutes:
after this, normal transmission operating conditions will
be restored.
Should the transmission failure condition persist, contact
the dedicated Alfa Romeo Dealership.
FUEL CUT-OFF SYSTEM
The symbol and the corresponding message are shown on
the display in the following cases:
❒ fuel cut-off system intervention:
the yellow symbol lights up;
❒ fuel cut-off system failure:
the red symbol lights up.For reactivating the fuel cut-off system, refer to the
description in the
“Fuel cut-off system” section in the “In an emergency”
chapter. If it is not possible to restore the fuel supply,
contact a dedicated Alfa Romeo Dealership.
s è

STARTING AND DRIVING
STARTING THE ENGINE........................................................................................ 68
PARKING .......................................................................................................................69
TCT TWIN CLUTCH TRANSMISSION ............................................................ 70
CRUISE CONTROL.................................................................................................... 75
PARKING SENSORS ............................................................................................... 77
REFUELLING THE CAR ......................................................................................... 79
Let’s get to the heart of the matter: seeing how you can exploit
all the potentials of your car to the fullest.
This is how to drive your car safely in all conditions for
pleasantly comfortable and cost-efficient travelling.

69
PARKING THE VEHICLE
Always remove the ignition key when
leaving the car.
When parking and leaving the car,
proceed as follows:
❒ engage the gear (on a slope, engage
first gear if the vehicle is facing uphill or
reverse if it is facing downhill) and leave
the wheels steered;
❒ stop the engine and engage the
handbrake.
Block the wheels with a wedge or a stone
if the car is parked on a steep slope.
Wait until the indication of the gear
engaged disappears on the display
before releasing the brake pedal.
76)
IMPORTANT NEVER leave the car with
the transmission in neutral.
HANDBRAKE
To engage the handbrake, pull lever
1 fig. 42 upwards until the car is secured.
When the handbrake is engaged and the
ignition key is at MAR, the xwarning
light will switch on in the instrument
panel.
To release the handbrake, raise the lever
1 slightly, hold down button 2 and lower
the lever.
The xwarning light on the instrument
panel turns off.
Four or five clicks are generally enough
when the car is on level ground, while ten
or eleven may be required if the car is on
a steep slope and laden.
77)
IMPORTANT Carry out these
manoeuvres with the brake pedal
pressed.
42A0L0066
76)Never leave children unattended in
the vehicle. Always remove the key from
the ignition device when leaving the
vehicle and take it with you.
77)The car must be braked after a few
clicks of the handbrake: if this is not so,
contact the dedicated Alfa Romeo
Dealership to have it adjusted. Always
park the car safely as indicated by the
Highway Code and as described above.
IMPORTANT

STARTING AND DRIVING
70
TCT TWIN CLUTCH
TRANSMISSION
Alfa 4C features the TCT 6-speed twin
dry clutch transmission with steering
wheel controls. This is an advanced
technical solution which combines the
control of a manual gearbox, the
immediacy of a sequential system and
the convenience of being able to select an
automatic selection programme without
the slowdown of a conventional
automatic transmission.
With the key removed from the ignition,
the system will not implement any action
when the buttons on the transmission
control panel on the central tunnel fig. 43
are pressed, irrespective of the pressure
applied to the brake pedal.
43A0L0067
Therefore, the transmission will remain in
the condition that it was in when the
engine was switched off.
With car stationary and key at MAR
(ignition-operated electrical services
activated), the screen displays the gear
engaged and the active operating mode
(automatic = AUTO or manual = no
display).
OPERATING MODE
The transmission can operate in two
operating modes (except when the “Race”
mode is selected):
❒ the first manual type (MANUAL), in
which the driver decides directly when to
change gear;
❒ the second completely automatic
(AUTO), in which the system decides
when to change gear.
When the “Race” mode is selected, the
only allowed operating mode is MANUAL.
Manual operation (MANUAL)
In this operating mode, the driver is
responsible for choosing the best gear
ratio to engage, depending on the car
operating conditions.Use the “+” steering wheel stalk to
engage a higher gear, or the “–” stalk to
engage a lower gear (see the following
paragraph, “Steering wheel stalks”).
If the request is accepted by the system,
the display shows the new gear engaged.
If the request is not accepted by the
system, the display shows the gear
engaged before the request and emits an
acoustic signal.
If the gear change request may adversely
affect the correct operation of the engine
and the transmission, the system will not
allow it.
44A0L0146

71
The system will automatically downshift
should the engine reach the idling speed
(e.g. during deceleration).
Using the DNA system in “Normal” mode,
it will automatically upshift if the engine
speed requires it.
Automatic operation (AUTO)
To activate/deactivate automatic
operation (AUTO) press the A/M button
on the transmission control panel fig. 43;
activation is signalled by the word AUTO
on the display, next to the gear engaged
fig. 45.
45A0L0068
In AUTO mode the system changes gear
depending on the car speed, the engine
rpm and the intensity with which the
accelerator pedal is pressed.
To move the stationary car, 1st gear or
reverse (R) must always be engaged
(with brake pedal depressed).
“Kick Down” function
The system also has the
“Kick Down” function: if necessary
(e.g. when overtaking), the system
changes down one or more gears when
the accelerator pedal is depressed
beyond the point where it becomes stiff
(and if the rpm allow it) in order to
provide suitable power and torque for the
acceleration requested by the driver.
When implementing the “Kick Down”
function, the system ensures varying
transmission management in accordance
with the selected DNA mode.
SHIFT PADDLES
These enable sequential gear shifting
fig. 46.
❒ shift paddle “+” (pulling paddle
towards driver, see fig. 47): shift up;
❒ shift paddle “–” (pulling paddle
towards driver, see fig. 47): shift down.
46A0L0071
47A0L0072

STARTING AND DRIVING
72
The shifting up or down is only permitted
if the engine revs allow it.
STARTING THE ENGINE
To start the engine press the brake pedal:
the system engages neutral (N)
automatically.
After the starting procedure, 1st gear (1)
or reverse (R) can be engaged.
Irrespective of the mode selected
(AUTO/MANUAL), to engage 1st gear or
reverse (R), it is necessary to press the
brake pedal and press the 1 button on the
transmission control panel (or the “+”
steering wheel stalk) to engage 1st gear
or the R button to engage reverse.
When 1st gear is engaged, the system
sets itself to AUTO mode.
Neutral (N) can be engaged again by
pressing the N button with the brake
pedal pressed.
When the 1, N or R buttons are pressed
(or “+” steering wheel stalk is operated)
without pressing the brake pedal, no gear
change request is implemented by the
system.
IMPORTANT Reverse cannot be engaged
by pressing the “-” stalk on the steering
wheel.
Important notes
To start in presence of a gearbox fault
(see “Warning lights and messages”
paragraph in the “Knowing the instrument
panel” chapter), run the
“Delayed start-up” procedure:
turn the key to the AVV position for at
least 7 seconds with the brake depressed
and the engine will start.
The system will remain in “recovery”
condition.
If the engine does not start, contact a
dedicated Alfa Romeo Dealership.
When the driver’s door is opened, the
system activates the hydraulic
components so that they are prepared
for the subsequent engine starting.
MOVING THE CAR
The car can set off both in 1st gear and
reverse (R).
The gears can only be engaged by
pressing the brake pedal. If the brake
pedal is not depressed, the display will
show a dedicated message.It is not possible to set off in a higher gear
than 1st: if this is attempted, the display
shows a dedicated message.
When setting off on a medium-steep
incline, it is advisable to engage the
handbrake.
Engaging 1st gear
Proceed as follows:
❒ press the brake pedal;
❒ press the 1 button on the
transmission control panel;
❒ release the brake pedal and press the
accelerator pedal.
Engaging reverse (R)
Reverse (R) can only be engaged with car
stationary and brake pedal pressed.
Proceed as follows:
❒ press the brake pedal (car completely
stationary);
❒ press button R on the
gearbox panel;
❒ release the brake pedal and press the
accelerator pedal.
When reverse is engaged on some
versions, the system emits an acoustic
signal.
If the brake pedal is not depressed (and
the vehicle is stationary), the display will
show a dedicated message and the
system will automatically engage neutral
(N).

73
IMPORTANT With the car running, the
request is accepted and executed if the
car speed drops below 3 km/h within 3
seconds from the request: if the request
is not executed, the system will maintain
the gear engaged or, if the speed of the
car drops below 10 km/h, will put the
transmission in neutral (N) and the
manoeuvre will have to be repeated.
ENGAGING NEUTRAL (N)
With car stationary and ignition key at
MAR (irrespective of the condition of the
engine), neutral (N) can only be engaged
with the brake pedal pressed.
If the car is in motion, neutral (N) can
always be engaged, irrespective of the
pressure applied to the brake and
accelerator pedals.
The display will show the letter N
together with the active operating mode.To engage a speed from the neutral (N)
position, press button 1 on the gearbox
panel (it is not necessary to press the
brake pedal):
the gearbox will immediately choose the
correct gear according to the vehicle’s
speed.
With car stationary and ignition key at
MAR (irrespective of the condition of the
engine), 1
stgear can only be engaged with
the brake pedal pressed.
LAUNCH CONTROL
The “Launch Control” strategy permits
high-performance starting.
This strategy can be activated with
vehicle at a standstill, “Race” mode
selected and 1st gear engaged.
The sequence of operations to perform is
as follows:
❒ press the brake pedal and hold it
down;
❒ press the accelerator pedal and hold it
down;
❒ press the “–” paddle behind the
steering wheel;The car will start off at maximum
acceleration when the brake pedal is
released.
Keeping the accelerator pressed, the
system will automatically upshift once
the best engine speed has been achieved
for shifting gears.
78)
To abandon the strategy, simply interrupt
the above sequence of operations or
release the accelerator pedal.
DISPLAYED INFORMATION
When the key is turned to MAR-ON, after
about 1 second, the display shows the
transmission in neutral indication (N).
When driving, the display shows the gear
engaged and the active mode (AUTO or
MANUAL). The indications on the display
have the following meanings:
N = neutral;
1 = first gear;
2 = second gear
3 = third gear;
4 = fourth gear;
5 = fifth gear;
6 = sixth gear;
R = reverse.

STARTING AND DRIVING
74
The car always starts in neutral. When
1st gear is requested, the system forces
the selection of AUTO mode.
IMPORTANT If 10 seconds elapse with
the ignition key in the MAR position and
the display does not show the gear
engaged, turn the key to the STOP
position, wait for the display to go out
and then repeat the manoeuvre.
If the fault persists, contact a dedicated
Alfa Romeo Dealership.
ACOUSTIC SIGNAL
For safety reasons, there is a buzzer
warning when parking the car with the
gearbox in neutral (N) (the warning is
heard when the ignition key is turned to
the STOP position).
With the vehicle stationary, the engine
started and (1st) or (R) engaged, the
system activates the buzzer and
automatically put the gearbox in neutral
(N) when:
❒ the accelerator and/or the brake
pedal are not operated for at least 3
minutes;
❒ the brake pedal is pressed for longer
than 10 minutes;❒ the driver’s door is opened and the
accelerator pedal or the brake pedal are
not operated for at least 1.5 seconds;
❒ a fault is detected in the gearbox.
PARKING THE CAR
When parking and leaving the car,
proceed as follows:
❒ engage the gear (on a slope, engage
first gear if the vehicle is facing uphill or
reverse if it is facing downhill) and leave
the wheels steered;
❒ stop the engine and engage the
handbrake.
Block the wheels with a wedge or a stone
if the car is parked on a steep slope.
Wait until the indication of the gear
engaged disappears on the display
before releasing the brake pedal.
IMPORTANT: NEVER leave the car with
the transmission in neutral.
IMPORTANT NOTES
❒ With car stationary and gear engaged,
always keep the brake pedal pressed
until you decide to set off, then release
the brake and accelerate gradually.
❒ During prolonged stops with the
engine running, it is advisable to keep the
gearbox in neutral (N).❒ In order to safeguard the efficiency of
the clutch, do not use the accelerator to
keep the car stationary (e.g. when
stopped on an incline). Clutch overheating
could damage it:
use the brake pedal instead or the
handbrake and only press the accelerator
pedal when you wish to set off.
❒ If, with reverse gear (R) engaged, you
have to engage 1st gear or vice versa,
only do this when the car is completely
stationary and with the brake pedal
pressed.
❒ Although it is strongly discouraged, if
you are going downhill and for unknown
reasons you let the car move forward
with the gearbox in neutral (N), when
there is a request to engage a gear the
system will automatically engage the
best gear in relation to the speed of the
actual to allow the correct transmission
of the drive torque to the wheels;.