technical specifications Alfa Romeo 8C 2007 Owner handbook (in English)

7VEHICLE IDENTIFICATION DATA
ACTIVE AND PASSIVE SAFETY
INSTRUMENTS AND CONTROLS
BEFORE YOU DRIVE
USING THE VEHICLE
IN AN EMERGENCY
CAPACITIES AND TECHNICAL SPECIFICATIONS
MAINTENANCE
TABLE OF CONTENTS

7
CAPACITIES AND TECHNICAL SPECIFICATIONS
Fuel ................................................................................................................................. 176
Engine oil ......................................................................................................................... 176
Capacities: quantity and specifi cations of the products to use .................................................... 177
Fuel consumption ..............................................................................................................179
CO2 exhaust emissions ........................................................................................................ 179
Technical specifi cations ....................................................................................................... 180
Tyre pressure ..................................................................................................................... 186

177
7
CAPACITIES AND TECHNICAL SPECIFICATIONS
CAPACITIES: QUANTITY AND SPECIFICATIONS OF THE
PRODUCTS TO USECAPACITIES AND RECOMMENDED PRODUCTS(*) For periodical replacement as provided for by the Maintenance Schedule or for any topping-up, contact the Authorised Service Centres of the Manufacturer’s Service Network to
have the proper products used. Parts to be refi lled Quantity Product specifi cations
Fuel tank
(including low fuel sector) approximately 86 litres Premium unleaded fuel with no less than 95 R.O.N.
Fuel reserve approximately 14 litres
Engine oil: Entirely synthetic multigrade lubricants SAE 5W/40 that meet API SL/CF and ACEA
A3, B3, B4 specifications.
- replace at regular intervals 9.0 litres Recommended oil: Selenia Motor Oil(*).
- top up from the MIN to the MAX
level1.5 litres
WARNING: Do not top up with oil whose specifications differ from those of the oil
already used in the engine.
WARNING: Engine oil consumption depends on the driving style and the conditions in
which the vehicle is used.
Windscreen/headlight washer fluid
tank6.5 litres Mix of water and detergent fluid, in the proportions indicated on the product package.
Detergent fluid: Mix of CUNA NC 956-II surfactants and alcohols.
Recommended fluid: TUTELA PROFESSIONAL SC 35 - Contractual Technical.
Reference No. F201.D02
WARNING: If the temperature is below –20°C, use pure detergent fluid.

178
7
Parts to be refi lled Quantity Product specifi cations
Engine cooling circuit 12.5 litres Mix of water and coolant, in the proportions indicated on the product package.
Coolant: inhibited monoethylene glycol-based protective fluid with anti-freezing
action: CUNA NC 956-16.
Recommended fluid: PARAFLU UP - Contractual Technical - Reference No. F101.M01
Hydraulic power steering - Oil type: ATF DEXRON II D LEV, SAE 10W.
Oil Type ATF Type A - MB 236.2 - ZF ML09/12
Recommended oil: TUTELA GI/A - Contractual Technical - Reference No. F002.B92
Gearbox 2.7 litres SAE 75W/90 above API GL4-GL5C API MT1-PG2 specifications
Recommended oil: TUTELA SPORT ZC SUPREME
“Q-Select” system ~0.5 litres Oil type: CHF
Recommended oil: TUTELA GI/R - Contractual Technical - Reference No. F428.H04
Braking system - Synthetic fluid: NHTSA n.116 DOT4, ISO 4925, SAE J1703 J1704, CUNA NC
956-01.
SAE J1703, FMVSS No. 116 DOT 4 and ISO 4925
Recommended fluid: TUTELA TOP 4 - Contractual Technical - Reference No. F001.A93
Air conditioning coolant 600 g R134a
Air conditioning compressor oil 200 cc
(+20/-10 ml)Type RL - 897 SAE J2297/98/99

179
7
CAPACITIES AND TECHNICAL SPECIFICATIONS
FUEL
CONSUMPTIONThe fuel consumption values shown in the
following table were established based on
homologation tests prescribed by specific
European Directives.
The test procedures followed for fuel
consumption measuring are described below:
- City cycle: This test begins with a cold start,
followed by simulation of an urban route;
- Highway cycle: This test involves frequent
accelerations in all gears, simulating use of
the vehicle on routes outside urban areas;
the speed varies between 0 and 120 km/h
- Average fuel consumption: This is
calculated considering a route consisting
of about 37% city cycle and 63% highway
cycle.FUEL CONSUMPTION FOLLOWING THE 2004/3/EC
DIRECTIVE (LITRES PER 100 KM)
City Highway Average
23.6 11.4 15.8WARNING: The type of route, traffic and weather conditions, driving style, general condition of the
vehicle, equipment/accessories in the vehicle, use of the air conditioning system, vehicle load and other
items or situations which may negatively affect the vehicle aerodynamics or wind resistance lead to
consumption ratios differing from the indicated ones.CO
2 EXHAUST EMISSIONS
The CO
2 exhaust emission ratings shown in the following table refer to an average fuel consumption.
CO2 EMISSIONS ACCORDING TO (*) DIRECTIVE
2002/80B/EC (G/KM)
City Highway Average
567 270 377

180
7
TECHNICAL SPECIFICATIONSENGINEGeneral
Type code AR8C
Cycle Otto
Cylinder number and position V 8 - 90°
Number of valves per cylinder 4
Bore and stroke mm 94x84.5
Total displacement cm3 4,691
Compression ratio 11.25±0.2
Maximum power (EC) kW 331
HP 450
corresponding RPM RPM 7,000
Maximum torque (EC) Nm 480
kgm 49
corresponding RPM RPM 4,750INJECTION – IGNITION
The ignition and injection system is controlled by
a single microprocessor ECU.
Injection
- Type Bosch Motronic ME7.1.1.
Ignition
- Static ignition
- Ignition sequence: 1-8-6-2-7-3-4-5
- Ignition coil:
ELDOR 78407003.C00
- Spark plugs: NGK PMR8C-H.
Battery
EXIDE 12V 88Ah 580A
Electric alternator
NIPPONDENSO SC2 150A

181
7
CAPACITIES AND TECHNICAL SPECIFICATIONS
LUBRICATION SYSTEM
The lubrication system uses a wet sump system
and oil pump with the relative suction screen,
incorporated in the crankcase.TRANSMISSION
Clutch
Dry double-plate clutch with servo-assisted
hydraulic control. COOLING SYSTEM
Engine cooling is obtained by means of an anti-
freeze mixture circulating inside a system with
radiator, centrifugal pump and expansion tank.

183
7
CAPACITIES AND TECHNICAL SPECIFICATIONS
SUSPENSION
Front and rear
Articulated quadrilateral suspension.
STEERING
Rack and pinion hydraulic steering, with pump
driven by the drive shaft and tank. Articulated
steering column, with energy absorption and
adjustable inclination and height.
- Steering diameter = 10.7 m
- Number of steering wheel turns = 1.3
(to the left and right)WHEELS
Wheel rims and tyres
Wheel rim size Tyre size
front 8.5”J x 20” 245/35 ZR20
rear 10.5”J x 20” 285/35 ZR20
*front 8.5”J x 20” 245/35 ZR20 VM+S
*rear 10.5”J x 20” 275/35 ZR20 VM+S
* Winter tyres
CAUTION
Alternatively, you may use winter tyres having the same dimensions as
those provided with the vehicle.
CAUTION
When winter tyres are fitted, it is advisable not to exceed a speed of 220
km/h. Always observe the regulations in force in the country where you are
driving and follow the instructions provided by the tyre manufacturer.
Spare wheel (Japan only)
Alloy wheel rim.Tyre size Tyre brand
175/55 R18 VREDESTEIN

185
7
910 mm 2645 mm
4381 mm826 mm
1590 mm
1341 mm
1589 mm
1894 mm
CAPACITIES AND TECHNICAL SPECIFICATIONS
DIMENSIONS

8VEHICLE IDENTIFICATION DATA
ACTIVE AND PASSIVE SAFETY
INSTRUMENTS AND CONTROLS
BEFORE YOU DRIVE
USING THE VEHICLE
IN AN EMERGENCY
CAPACITIES AND TECHNICAL SPECIFICATIONS
MAINTENANCE
TABLE OF CONTENTS