ECO mode Alfa Romeo GT 2007 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
116
STOPPING THE CAR
To stop the car, simply release the accel-
erator pedal and, if necessary, press the
brake pedal.
Regardless of the gear engaged and the
operating mode activated (MANUALor
CITY) the system automatically disengages
the clutch and shifts to a lower gear.
If deciding to move off again without hav-
ing stopped the car completely, the most
suitable ratio will be available for accelera-
tor again.
Stopping the car the system automatical-
ly engages first gear (1).
OPERATION
The gearbox can work according to two op-
erating modes:
– the first one is semi-automatic (MAN-
UAL): the decision to change gear is left to
the driver who decides the most appropriate
moment; this mode features the two fol-
lowing logics:
1) normal: for comfort driving;
2) sport: (to be activated by button B-
fig. 124): for sporty driving.
Sport operating mode is selected by press-
ing button SPORT(B-fig. 124) set on
the gearshift lever; when selecting this
mode, the display will show SPORT.– the second one is fully automatic
(CITY), in which the system decides di-
rectly when to shift gear according to driving
conditions.
To select the CITYmode, press button
CITYset on the gearshift lever; when se-
lecting this mode, the display will show
CITY.

GETTING TO KNOW YOUR CAR
118
With the accelerator pedal pressed to over
60% of its stroke and an engine speed
above 5000 rpm, gearshifting becomes
quicker. In the MANUALoperating mode
there are certain automatic/security devices
which simplify driving:
– when slowing down, the clutch is dis-
engaged and the gear ratio is reduced au-
tomatically to be ready for possibly picking
up speed again; if not, stopping the car, first
gear (1) will be engaged automatically;
– request to change gear that could take
the engine above the maximum rpm or be-
low the minimum permissible rpm are not
accepted;AUTOMATIC OPERATION (CITY)
TheCITYautomatic operating mode is se-
lected pressing the button (A-fig. 126)
at the base of the gearshift lever.
In addition to the gear, the display will
show the word CITY.
The system decides directly when to shift
gears in relation to the engine rpm and dri-
ving conditions.
Releasing the accelerator pedal quickly, the
system does not engage a higher gear in or-
der to maintain an adequate level of engine
brake.
fig. 126
A0A0701b
– if sticking occurs during the engagement
of a gear, the system firstly tries to engage
the required gear again and, if it is still not
possible, it automatically engages the im-
mediately higher one to avoid leaving the
car in neutral .
IMPORTANTIt is advisable to wait for
the end of a gear shifting operation before
requesting another one, to avoid multiple
requests in rapid succession.

GETTING TO KNOW YOUR CAR
119
In the event of whatever
transmission fault, contact
Alfa Romeo Authorized Ser-
vices as soon as possible to have
the system checked. In the event of a fault to the gearshift lever,
the system automatically activates the au-
tomaticCITYmode to allow the car to
reach the nearest Alfa Romeo Authorized
Services to have the fault detected elimi-
nated.
In the event of a fault to the other gear-
box components, the system only allows the
engagement of certain gears: first gear (1),
second gear (2) and reverse (R).
FAILURE INDICATIONS
Failures to the Selespeed gearbox are in-
dicated on the display by warning light
t
(fig. 127), dedicated message and
buzzer. If the warning light
t
and the message are dis-
played, contact Alfa Romeo
Authorized Services as soon as
possible to have the fault elimi-
nated.
fig. 127
A0A9081g

GETTING TO KNOW YOUR CAR
149
Compact Disc section
– Direct disc selection;
– Track selection (forward/backward);
– Fast forward/backward;
– CD Display function: displaying CD
name/time elapsed from start of track;
– Playing audio CDs and R/RW CDs. CD MP3 section
– Directory selection (previous/next);
– Track selection (forward/backward);
– Fast forward/backward;
– MP3 DISP function: directory name, ID3-
tag info, time elapsed from start of track,
file name);
– Playing audio CDs and R/RW CDs.
Audio section
– Mute/Pause function;
– Soft Mute function;
– Loudness function (excluding versions
with Bose HI-FI system);
– 7 band graphic equalizer (excluding ver-
sions with Bose HI-FI system);
– Separate bass/treble adjustment;
– Right/left channel balancing. GENERAL
The set possesses the following functions:
Radio section
– PLL tuning with FM/AM/MW/LW fre-
quency bands;
– RDS (Radio Data System) with TA (traf-
fic announcements) - TP (Program Type) -
EON (Enhanced Other Network) - REG (Re-
gional programmes);
– AF: alternative frequency search selec-
tion in RDS mode;
– emergency alarm presetting;
– automatic/manual station tuning;
– FM Multipath detector;
– manual storage of 36 stations: 18 in
the FM band (6 in FM1, 6 in FM2, 6 in
FMT), 6 in the MW band and 6 in the LW
band;
– automatic storage (Autostore function)
of 6 stations in FM band;
– SVC function (excluding versions with
Bose HI-FI system): automatic volume ad-
justment with car speed;
– automatic Stereo/Mono switching.On multimedia CDs in ad-
dition to sound tracks also
data tracks are recorded.
Playing one of these CDs may
cause rustling and such a volume
as to compromise road safety, as
well as causing damage to the fi-
nal stages and speakers.

GETTING TO KNOW YOUR CAR
151
Audio adjustments
The options proposed by the audio menu
differ according to the audio source select-
ed: AM/FM/CD/CDC.
To change Audio functions, press briefly
button AUD. The display will show “BASS”.
To scroll the Menu options, use buttons
▲
or▼. To change the setting of the option
selected, press buttons
÷or˜.
The display will show the current status
of the function selected.
The functions controlled by the menu are
the following:
– BASS (bass adjustment);
– TREBLE (treble adjustment);
– BALANCE (right/left balance);
– FADER (excluding versions with Bose HI-
FI system) (front/rear balance);
– LD (excluding versions with Bose HI-FI
system) (Loudness on/off);
– PRESET (excluding versions with Bose
HI-FI system) (standard equalization acti-
vation and selection);
– XX USER (personal equalization set-
ting).Tone adjustment
(bass/treble)
Proceed as follows:
– Use button
▲or▼to select “BASS” or
“TREBLE” in the AUDIO menu;
– press button
÷or˜to in-
crease/decrease the basses or trebles.
Pressing the buttons briefly the change is
gradual by steps. Pressing longer, chang-
ing is faster.
Balance adjustment
Proceed as follows:
– Use button
▲or▼to select “BAL-
ANCE” in the AUDIO menu;
– press button
÷to increase the sound
from the right speakers or button
˜to
increase the sound from the left speakers.
Pressing the buttons briefly the change is
gradual by steps. Pressing longer, chang-
ing is faster.
Select “
÷0˜” to set the same val-
ue for both right and left speakers. Mute /pause function
(turning off the volume
completely)
To switch on the Mute function, briefly
press the button MUTE. Volume will gradu-
ally lower and the display will show the word
“MUTE” (when in radio mode) or “PAUSE”
(when in CD or CD-Changer mode).
To switch off the Mute function, press the
button MUTE again. Volume will gradually
become louder returning to the value set be-
fore switching on the Mute function.
Changing volume will deactivate the Mute
function and the volume will be set to the
new level selected.
With the Mute function on:
– if an emergency alarm or a traffic bul-
letin arrives with the TA function on, the mes-
sage ignores the Mute function. The Mute
function will be resumed at the end of the
traffic announcement.

GETTING TO KNOW YOUR CAR
153
Each band is shown by the respective
wording on the display.
The last station selected in the respective
frequency band will be tuned.
The FM band is divided into sections: FM1,
FM2 and FMT. The FMT reception band is
reserved to the stations stored automatically
with the Autostore function.
Presetting buttons
The buttons with symbols from 1 to 6
make it possible to set the following pre-
settings:
– 18 in the FM band (6 in FM1, 6 in
FM2, 6 in FMT);
– 6 in the MW band;
– 6 in the LW band;
To call a preset station, choose the required
frequency band and then press briefly the
corresponding preset button (from 1 to 6).
Pressing the respective preset button for
longer than 2 seconds will store the tuned
station. Storing is confirmed by a beep. Storing the last station heard
The radio automatically keeps in storage
the last station heard for each reception
band, which is then tuned when the radio is
turned on or the reception band is changed.
Automatic tuning
Briefly press button
÷or˜to start
automatically searching the tuning for the
next station that it is possible to receive in
the direction chosen.
If button
÷or˜is pressed for
longer, quick searching takes place. When
the button is released, the tuner stops on
the next receivable station.
If the TA function is on (traffic information),
the tuner only searches stations which broad-
cast traffic bulletins.
RADIO (TUNER)
Introduction
When the set is turned on the last function
selected before turning off is played (Radio,
CD or CD Changer).
To select the Tuner source while listening
to another audio source, press briefly but-
tons FM
ASor AM, according to the required
frequency band.
When Tuner is on, the display will show
the selected station name (RDS stations on-
ly) (or frequency), the frequency band (e.g.:
FM1) and the preselection button number
(e.g.: P1).
Selecting the frequency band
If in the Tuner mode, briefly and repeat-
edly press button FM
ASor AM to select the
required frequency band.
Every time the button is pressed the fol-
lowing bands are selected in sequence:
– Pressing button FM
AS: “FM1”, “FM2”,
“FMT”;
– Pressing button AM: “MW” and “LW”.

GETTING TO KNOW YOUR CAR
161
Entering the secret code
When turning the sound system on (in the
event of code request), the display will show
the word “CDC CODE” for about 2 seconds,
followed by four dashes “- - - -”.
The secret code comprises four figures from
1 to 6, each corresponding to one of the
dashes.
To enter the first digit of the code, press
the corresponding key of the preset stations
(from 1 to 6). Enter the other code digits in
the same way.
If the four figures are not entered within
20 seconds, the display shows the word
“CDC CODE” for 2 seconds and then fours
dashes “- - - -”. This is not to be considered
as an incorrect code entry.
After entering the fourth digit (within 20
seconds), the radio starts working.
If a wrong code is entered, the radio
sounds a beep, the display shows the word
“CDC CODE” for 2 seconds and then fours
dashes “- - - -” to warn the user that it is nec-
essary to enter the correct code. Every time the user enters a wrong code,
the waiting time increases gradually (1 min,
2 min, 4 min, 8 min, 16 min, 30 min,1h,
2h, 4h, 8h, 16h, 24h) until reaching a max-
imum of 24 hours. The waiting time will
be shown on the display with the word “CDC
WAIT”. When this goes off it is possible to
start the new code entry procedure.
Code Card
This the document that certifies possession
of the radio. The Code Card contains the ra-
dio model, serial number and secret code.
IMPORTANTKeep the Code Card care-
fully to be able to give the related data to
the competent authorities in the event of
theft. Antitheft protection
The radio is fitted with an antitheft pro-
tection system based on the exchange of in-
formation between the radio and the elec-
tronic control unit (Body Computer) installed
on the car.
This system warrants the highest level of
security and prevents entry of the secret
code every time the radio supply is discon-
nected.
If the result of the check is positive, the set
starts working, whereas if the comparison
codes are not the same or if the electronic
control unit (Body Computer) is replaced,
the device informs the user of the need to
enter the secret code according to the pro-
cedure described in the following paragraph.

GETTING TO KNOW YOUR CAR
162
Technical data and operating conditions for
MP3 files are as follows:
– adopted CD-ROM shall be mastered ac-
cording to ISO9660 Standard;
– music files shall be renamed as “.mp3”
otherwise they cannot be played;
– sampling frequencies are: 44.1 kHz,
stereo (96 to 320 kbit/s) - 22.05 kHz,
mono or stereo (32 to 80 kbit/s);
– it is possible to play variable bit-rate
tracks (files).
IMPORTANTCharacters: blank, ‘ (apos-
trophe), ( and ) (open and closed brackets)
are not admitted in MP3 track names. When
sampling MP3 CD you must not use these
characters to name files otherwise the sound
system will not be able to play it. DISPLAY INFORMATION
ID3-tag info display
(track informations)
In addition to time elapsed, directory name
and file name, also ID3-tag info relevant to
track Title, Artist, Author (see section “MP3
disp function”) are displayed.
The MP3 directory name shown on the dis-
play corresponds to the name with which
the directory is stored on the CD, followed
by an asterisk.
Example of full MP3 directory name: BEST
OF *.
If you want to display one ID3-tag info (Ti-
tle, Artist, Album) and the track being played
has no ID3-tag info then, the file name will
be displayed.
MP3 CD PLAYER
(where provided)
Introduction
This section only describes MP3 CD play-
er operation variants: as concerns sound sys-
tem operation, refer to “Functions and Ad-
justments” paragraph.
NOTEMPEG Layer-3 audio decoding tech-
nology licensed from Fraunhofer IIS and
Thomson multimedia.
MP3 mode
In addition to standard audio CDs, the sound
system can also play audio files in MP3 for-
mat. Sound system will operate as described
in “Compact Disc player” paragraph when in-
serting a conventional audio CD.
For optimal playing use only top quality
CDs mastered at a speed as low as possible.
MP3 CD files are structured by directories,
with sequential lists of all directories con-
taining MP3 tracks (directories and sub-di-
rectories are all brought to the same lev-
el), directories not containing MP3 tracks
cannot be selected.

CORRECT USE OF THE CAR
177
It is necessary therefore to limit their use
to the purposes for which they are certified.
IMPORTANTWhen winter tyres are
used with a maximum speed index below
the one that can be reached by the car (in-
creased by 5%), place a notice in the pas-
senger’s compartment, plainly in the driver’s
view, which states the maximum permissi-
ble speed of the winter tyres (as per EC Di-
rective).
Fit the same type of tyre on all four wheels
(brand and profile) to ensure higher driving
safety when braking and good handling.
Remember that it is inappropriate to
change the direction of rotation of tyres.WINTER TYRES
These tyres are specially designed for dri-
ving on snow and ice, to be fitted in re-
placement of those fitted on the car.
Use winter tyres of the same size as nor-
mal tyres provided on the car.
Alfa Romeo Authorised Services will be
pleased to advise you on the choice of the
tyre most suited to the use the Customer in-
tends to make of it.
For the type of tyre to be used, inflation
pressures and specifications of winter tyres,
follow the instructions given in the “Tech-
nical Specifications” chapter.
The winter features of these tyres are re-
duced considerably when the tread depth
is below 4 mm. In this case, they should be
replaced.
Due to the winter features, under normal
conditions of use or long motorway jour-
neys, the performance of these tyres is low-
er than that of normal tyres.
SNOW CHAINS
Use of snow chains should be in compli-
ance with local regulations.
For 1.8 T. SPARK, 2.0 JTS and 1.9
JTD versions, tyre 195/60 R15 can be
fitted with chains (use snow chains with re-
duced size with max protrusion beyond the
tyre profile of 12 mm). Tyres 205/60 R15
- 205/55 R16 - 205/55 ZR16 - 215/45
R17 - 215/45 ZR17 - 225/40 ZR18 can-
not be fitted with snow chains.
For 3.2
V6version, only use spider type
chains on tyres 215/45 R17” and
215/45 ZR 17”. Tyres 225/45 ZR17 -
225/40 ZR18 cannot be fitted with snow
chains.
Lineaccessori Alfa Romeo provides SPIKES
SPIDER COMPACT chains (model: 17003
compact) with 9 spikes, 16 mm adjustable
length and 17 inch wheel cap adapter.
Snow chains should only be applied to the
drive wheels (front).
Before purchasing or using snow chains,
you are recommended to contact Alfa
Romeo Authorised Services.
Check the tensions of the chain after the
first few metres have been driven.