light Alfa Romeo GT 2010 Owner handbook (in English)

CAR MAINTENANCE
223
A0A0396b
fig. 4 - JTD 16V version1Engine oil - 2Battery - 3Brake fluid -
4Windscreen/rearscreen/headlamp wash-
er fluid - 5Engine coolant fluid - 6Power
steering fluid
A0A0683b
fig. 3 - 3.2 V6 version 1Engine oil - 2Battery - 3Brake fluid -
4Windscreen/rear window/headlight
washer fluid - 5Engine coolant - 6Power
steering fluid

CAR MAINTENANCE
228
Do not travel with the
windscreen washer reser-
voir empty: the action of
the windscreen washer is funda-
mental for improving vision.
To avoid damaging the
pump motor, do not use the
windscreen/rearscreen
washers when the reservoir is
empty.
Some commercial addi-
tives for windscreen wash-
ers are inflammable. The
engine compartment contains hot
components which may set it on
fire.
IMPORTANTBrake and hydraulic clutch
fluid is hygroscopic (i.e. it absorbs moisture).
For this reason, if the car is mainly used in
areas with a high degree of atmospheric hu-
midity, the fluid should be replaced at more
frequent intervals than specified in the
Scheduled Maintenance Programme.
WINDSCREEN/REARSCREEN
HEADLIGHT WASHER FLUID
(fig. 13)
Open the cap (A) and check the level in
the reservoir.
If necessary top up using a mixture of wa-
ter and TUTELA PROFESSIONAL SC
35fluid as follows:
– 30% of TUTELA PROFESSIONAL
SC 35and 70% water in summer; Brake and clutch fluid is
poisonous and highly cor-
rosive. In the event of ac-
cidental contact, wash the parts
concerned immediately with neu-
tral soap and water, then rinse
thoroughly. See a doctor at once if
the fluid is swallowed.
Theπsymbol on the con-
tainer indicates synthetic
brake fluid, distinguishing
it from the mineral kind. Using min-
eral fluids irreversibly damages the
special braking system rubber
seals.
fig. 13
A0A0242b
– 50% of TUTELA PROFESSIONAL
SC 35and 50% water in winter;
– in the case of temperatures below
–20°C use TUTELA PROFESSIONAL
SC 35fluid neat. Make sure that the high-
ly corrosive brake fluid
does not drip onto the
paintwork. If it does, wash it off
immediately with water.

CAR MAINTENANCE
232
Proceed as follows with doors closed:
1.open completely the driver’s window
keeping the button pressedfor at
least 3 seconds after full opening;
2.close completely the driver’s window
keeping the button pressedfor at
least 3 seconds after full closing;
3.proceed as described in points 1 and
2 also for the passenger’s side;
4.check for proper initialisation by oper-
ating the windows in automatic.
USEFUL HINTS TO EXTEND
THE LIFE OF YOUR BATTERY
To avoid rapidly draining the battery and
ensure that it continues to work correctly,
the following should be noted:
– The terminals must always be firmly
tightened.
– As far as possible, avoid keeping ser-
vices on for a long time with the engine
stopped (radio, hazard lights, parking lights,
etc.). IMPORTANTIf the battery is kept with
a charge of below 50% it is damaged by sul-
phation, its starting capability is reduced and
it is also more subject to the possibility of
freezing (this may occur already at -10 °C).
In the event of a prolonged inactivity, refer
to the paragraph “car inactivity”, in the
chapter “Correct use of the car”.
CHANGING
THE BATTERY
When changing the battery it should be re-
placed with another original one with the
same characteristics. If it is replaced by a
battery with different characteristics, the
maintenance intervals given in the Sched-
uled Maintenance Programme in this chap-
ter are no longer valid and for maintenance
it will be necessary to follow the battery
Manufacturer’s instructions.
IMPORTANTLacking power to control
units (e.g. battery change/disconnection
and replacement of power window control
unit protection fuses), window automatism
must be reset.– When leaving the car parked in a
garage, make sure that the doors, bonnet,
boot and interior lids are properly shut to
prevent lights from staying on.
– Before carrying out any work on the
electric system, disconnect the negative ca-
ble from the battery.
– If after buying the car, you wish to in-
stall electric accessories which require a per-
manent electric supply (alarm, voice feature,
radionavigator with satellite antitheft func-
tion etc.) or accessories that burden the elec-
tric system, contact Alfa Romeo Authorised
Services whose qualified personnel, in ad-
dition to suggesting the most suitable de-
vices belonging to Lineaccessori Alfa Romeo,
will evaluate the overall electric absorption,
checking whether the car’s electric system
is capable of withstanding the load required,
or whether it should be integrated with a
more powerful battery. In fact, as some of
these devices continue absorbing energy
even when the ignition key is off (car sta-
tionary, engine off), they gradually drain the
battery.

CAR MAINTENANCE
236
HEADLIGHT WASHERS
(fig. 19)
Regularly check that the spray jets are in-
tact and clean.
If it is necessary to direct the jet, contact
an Alfa Romeo Authorized Service.
BODYWORK
PROTECTION FROM
ATMOSPHERIC AGENTS
The main causes of corrosion are:
– atmospheric pollution
– salty air and humidity (coastal areas, or
hot humid climates)
– seasonal environment conditions.
Not to be underestimated is also the abra-
sive action of wind-borne atmospheric dust
and sand and mud and gravel raised by oth-
er cars.
On your car, Alfa Romeo has implement-
ed the best manufacturing technologies to
effectively protect the bodywork against cor-
rosion.
fig. 19
A0A0704b
These include:
– Painting products and systems which
give the car particular resistance to corrosion
and abrasion.
– Use of galvanised (or pretreated) steel
sheets, with high resistance to corrosion.
– Spraying of the underbody, engine com-
partment, wheel arches and other parts with
highly protective wax products.
– Spraying of plastic parts, with a protec-
tive function, in the more exposed points:
underdoor, inner wheel arch linings, etc.
– Use of “open” boxed sections to pre-
vent condensation and pockets of moisture
from triggering rust inside.
CAR EXTERIOR AND
UNDERBODY WARRANTY
Your car is covered by warranty against
perforation due to rust of any original ele-
ment of the structure or body. For the gen-
eral terms of this warranty, refer to Alfa
Romeo Warranty booklet.

CAR MAINTENANCE
237
Detergents cause water
pollution. Therefore the car
should be washed in areas
equipped for collecting and purify-
ing the liquid used in the washing
process.Where possible, do not park under trees;
the resinous substances many species re-
lease give the paint a dull appearance and
increase the possibility of triggering the rust
processes.
IMPORTANTBird droppings must be
washed off immediately and thoroughly as
the acid they contain is particularly aggressive.
To correctly wash the car:
1) Remove the aerial from the roof to pre-
vent damage to it if the car is washed in
an automatic system.
2) Spray the car with a low pressure jet of
water.
3) Pass a sponge moistened with a light
detergent solution, rinsing the sponge fre-
quently.
4) Rinse well with water and dry with a
jet of air or chamois leather.
When drying, take particular care with the
less visible parts like door surrounds, bon-
net and around the headlights where wa-
ter may stagnate. The car should not be tak-
en to a closed area immediately, but left in
the open so that residual water can evapo-
rate.
Do not wash the car after it has been left
in the sun or with the bonnet hot: this may
alter the shine of the paintwork.
Exterior plastic parts must be cleaned in
the same way as the rest of the car.ADVICE FOR PRESERVING
THE BODYWORK
Paint
The paintwork does not only serve an
aestethic purpose but also protects the un-
derlying sheet metal.
In the case of deep scrapes or scores, you
are advised to have the necessary touch-
ing up carried out immediately to avoid the
formation of rust.
Only original products should be used for
touching up paint (see “Body paint identi-
fication plate” in the “Technical Specifica-
tions” chapter).
Normal paint maintenance consists in
washing at intervals depending on the con-
ditions and environment of use. For exam-
ple, in highly polluted areas, or if the roads
are sprayed with salt, it is wise to wash the
car more frequently.

CAR MAINTENANCE
238
Engine compartment
At the end of the winter the engine com-
partment should be carefully washed, with-
out directing the jet against electronic con-
trol units. Contact a specialised workshop to
have this done.
Detergents cause water
pollution. Therefore the en-
gine compartment should
be washed in areas equipped for
collecting and purifying the liquid
used in the washing process.
IMPORTANTThe car should be washed
with the engine cold and the ignition key at
STOP. After washing make sure that the
various protections (e.g. rubber caps and
various covers) have not been damaged or
removed. Windows
Use specific products to clean the windows.
Use clean cloths to avoid scratching or al-
tering the transparency of the glass.
IMPORTANTThe inside of the
rearscreen should be wiped gently with a
cloth in the direction of the filaments to
avoid damaging the heating device.
Front headlights
IMPORTANTDo not use aromatic sub-
stances (e.g. petroleum) or ketones (e.g.
acetone) to clean the front headlight plas-
tic transparents.
Never use inflammable
products like fuel oil ether
or rectified petrol for clean-
ing inside the car. The electrostat-
ic charges generated when rubbing
to clean may cause fire.
INTERIOR FITTINGS
Periodically check that water is not trapped
under the mats (due to water dripping off
shoes, umbrellas, etc.) which could cause
oxidisation on the sheet metal.
CLEANING SEATS AND FABRIC
AND VELVET PARTS
– Use a soft brush or a vacuum cleaner to
remove dust. Velvet is cleaned better if the
brush is moistened.
– Rub the seat with a sponge moistened
with a solution of water and neutral deter-
gent.

CAR MAINTENANCE
239
Do not keep aerosol cans
in the car. There is the risk
they might explode. Aerosol
cans must never be exposed to a
temperature above 50°C. The tem-
perature inside the car might go well
beyond that figure when exposed
to the sun’s rays.
INTERIOR PLASTIC PARTS
For routine cleaning of interior plastic parts
use a soft cloth moistened with water and
neutral soap. Remove grease or persisting
stains using appropriate solvent-free prod-
ucts designed to preserve appearance and
colour of plastic components.
IMPORTANTNever use spirit or petro-
leum to clean the glass of the instrument
panel or other plastic components.
STEERING WHEEL/GEAR LEVER
KNOB WITH GENUINE LEATHER
COVERING
These components shall only be cleaned
with water and neutral soap. Never use spir-
it or alcohol-based products.
Before using special products for cleaning
interiors, read carefully label instructions and
indications to make sure they are free from
spirit and/or alcohol-based substances. If
when cleaning the windscreen with special
glass products, some drops fall on the
leather covering of the steering wheel/gear
lever knob remove them immediately and
then clean with water and neutral soap.
IMPORTANTTake the utmost care
when engaging the steering lock to prevent
scratching the leather covering.
CLEANING LEATHER SEATS
– Remove dried on dirt with a lightly
moistened chamois leather or cloth with-
out pressing too hard.
– Remove liquid and grease stains with
a dry absorbent cloth without rubbing. Then
wipe with a soft cloth or chamois leather
with water and neutral soap. If the stain per-
sists, use specific products, carefully follow-
ing the instructions for use.
IMPORTANTNever use spirit or alco-
holbased products, even in small percentage.
Fabric upholstery of your
car is purpose-made to
withstand common wear
resulting from normal use of the
car. It is however absolutely nec-
essary to prevent hard and/or pro-
longed scratching/scraping caused
by clothing accessories like metal-
lic buckles, studs, “Velcro” fixings,
etc. that stressing locally the fabric
could break yarns and damage the
upholstery as a consequence.

DIMENSIONS
fig. 5
ABCDEFGH
1.8 T. SPARK - 2.0 JTS4489 967 2596 926 1362 1763 1524 1510
3.2V64489 967 2596 926 1355 1763 1524 1510
JTD16V4489 967 2596 926 1366 1763 1524 1510
The sizes are
in mm and
refer to the car fitted with
standard tyres.
Slight changes with
optional tyres.
Height with
unladen vehicle.
LUGGAGE COMPARTMENT
VOLUME
Capacity .................................. 320 dm3
Capacity with rear seat back
rest folded ................................ 905 dm3
A0A0653b
TECHNICAL SPECIFICATIONS
250

RIGHT HAND DRIVE VERSION
257
DASHBOARD
fig. 1
A0A0724b
1.Adjustable side air vents - 2.Fixed side window air vents -3.Front passenger’s air bag - 4.Tailgate release button - 5.Cards holder (for versions/mar-
kets where applicable) - 6. Sound system (for versions/markets where applicable) -7.Adjustable central air vents - 8.Upper fixed vent - 9.Glass/can
holder (for versions/markets where applicable) - 10.Front fog light button - 11.Hazard light switch - 12.Rear fog light button - 13.External lights con-
trol lever - 14.Instrument panel - 15.Windscreen wiper stalk - 16. Bonnet opening lever - 17.Set of controls - 18.Ignition key and ignition switch - 19.
Horn - 20.Steering wheel locking/release lever - 21.Driver’s air bag - 22.Door locking button - 23.Heating/ventilation/climate controls - 24.Cigar
lighter/ashtray housing lid - 25.Temperature sensor - 26.Glovebox.

RIGHT HAND DRIVE VERSION
258
INSTRUMENT
PANEL
A.Fuel level gauge with reserve warning
light - B.Engine coolant fluid temperature
gauge with maximum temperature warning
light - C.Speedometer - D.Odometer dis-
play (mileage recorder, trip recorder with
headlamp position display - E.Reconfig-
urable multifunction display - F.Rev counter
NOTEOn JTDM versions the scale bot-
tom is at 6000 revs.
A.Fuel level gauge with reserve warning
light - B.Engine coolant fluid temperature
gauge with maximum temperature warning
light - C.Speedometer - D.Odometer dis-
play (mileage recorder, trip recorder with
headlamp position display - E.Reconfig-
urable multifunction display - F.Rev counter
NOTEOn JTDM versions the scale bot-
tom is at 6000 revs.
A0A0762b
A0A0754b
fig. 2 - Petrol versions
fig. 3 - Black Line versions