gearbox Alfa Romeo GT 2010 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
109
To release the hand brake:
– slightly lift the lever (A) and press the
release button (B);
– keeping the button pressed lower the
lever, the warning light
xon the instru-
ment cluster will go out.
To prevent the car from moving acciden-
tally, keep the brake pedal pressed when
engaging the hand brake.
IMPORTANTThe hand brake lever (A)
is fitted with a safety device which prevents
the brake from being released when, with
the lever pulled, button (B) is pressed.
Therefore, to release the brake, in addition
to pressing button (B), it is also necessary
to pull lever (A) further upwards to release
the safety device, then lower the lever com-
pletely.
IMPORTANTOn certain versions a
buzzer sounds to alert the driver if the car
is moved with the hand brake engaged.
GEARSHIFT LEVER (fig. 116)
The position of the single gears is shown
by the pictogram on the gearshift lever knob.
When shifting gear, always fully depress
the clutch pedal. Before engaging reverse
gear (R) wait for the car to be stationary.
Certain versions are equipped with 6-speed
gearbox. For the versions with 6 gears, to
engage reverse (R) lift (with the fingers
of the same hand holding the lever) the ring
(A-fig. 116) positioned under the lever.
After engaging the reverse, release the ring.
To change from reverse to another gear, it
is not necessary to lift the ring on the lever.
IMPORTANTReverse gear may only be
engaged with the car completely at a stand-
still. With the engine running, before en-
gaging reverse gear it is necessary to wait
for at least 3 seconds with the clutch pedal
fully depressed to prevent clashing and the
possibility of damaging the gears. To change gear smoothly,
the clutch pedal must be
fully depressed. Therefore,
there should be no obstacles on the
floor under the pedal unit: make
sure that any mats are well laid and
do not interfere with the pedals.
fig. 116
A0A0684b

GETTING TO KNOW YOUR CAR
110fig. 119
A0A9017i
The gearbox can work according to two op-
erating modes:
– the first is semi-automatic (hereinafter
calledMANUAL), in which the driver shifts
gear directly using the lever on the central
console or the levers on the steering wheel
spokes;
– the second is automatic, called CITY
(when selecting CITYwith button B-fig.
117, the word CITYwill be displayed fig.
119). In this mode the system decides di-
rectly when to shift gear. SELESPEED
TRANSMISSION
(on request for versions/markets
where applicable)
IMPORTANTTo be able to use the Se-
lespeed correctly, this chapter should be read
in full to understand the correct, permissible
operations to be carried out right from the
start.
This device comprises a conventional me-
chanical transmission, to which an elec-
tronically-controlled electrohydraulic device
has been added, which automatically con-
trols the clutch and gear engagement.
The clutch pedal has been eliminated and
the car moves off using only the accelerator
pedal.Gearshifting takes place through a floating
control lever (A-fig. 117) with “only one
stable central position”. Using this lever it is
possible to request increase/decrease of the
ratio of the gear engaged and/or engage-
ment of reverse gear (R) or neutral (N).
There are also two levers on the steering
wheel spokes (fig. 118) through which,
only with the car on the move (with speed
above 0,5 km/h), it is possible to in-
crease/decrease the gear engaged.
fig. 117
A0A0697b
fig. 118
A0A0669b

GETTING TO KNOW YOUR CAR
111
SYSTEM ACTIVATION
IMPORTANTOpening the driver’s door,
the Selespeed starts the hydraulic part of
the system to prepare it for the engine to be
started.
Turning the ignition key to MAR, all the
segments of the display (fig. 119), the
gearbox warning light (fig. 120) and the
wordCITYturn on. After about one second,
the display indicates the gear engaged (N,
1,2,3,4,5,R).
IMPORTANTIf after 10 seconds the dis-
play segment do not display the gear en-
gaged or the warning light stays on, turn the
ignition key to STOPand wait for the dis-
play to go off, then repeat the system acti-
vation procedure. If the fault persists, con-
tact Alfa Romeo Authorized Services. With gearshift to CITYgears can be shift-
ed manually using both the gearshift lever
or the steering wheel controls. Gearshift
stays in CITY.
The gear selected (fig. 119) is always
displayed regardless of the mode being se-
lected selected .
N= neutral;
1= first gear;
2= second gear;
3= third gear;
4= fourth gear;
5= fifth gear;
R= reverse. InCITYorSPORT, the selected mode is
also displayed.
IMPORTANT SPORTmode can only
be activated after deactivating the CITY
mode.
A warning light, a message (fig. 120)
and a buzzer draw the attention of the dri-
ver in the event of a fault at Selespeed trans-
mission.
The Selespeed considerably simplifies use
of the car, reducing the fatigue of city dri-
ving or when frequent gearshifting is re-
quired, at the same time offering brilliant
performance.
fig. 120
A0A9081g

GETTING TO KNOW YOUR CAR
113
Never remove the ignition
key when the car is mov-
ing. In addition to the fact
that the Selespeed system would
not work properly up to stopping
the car, the steering wheel would
lock automatically the first time it
is turned.
STARTING THE ENGINE
The engine can be started with the gear
engaged or in neutral (N), provided that the
brake pedal is pressed down.
IMPORTANTKeep the pedal fully de-
pressed during starting. Since the brake ped-
al becomes hard if it is pressed repeatedly
with the engine off, in this situation it is nec-
essary to increase the pressure on the ped-
al itself to start the engine.
After starting, the gearbox sets to neutral
automatically, the display shows the letter
(N) and the system selects the operating
mode memorised before switching off.
If the engine fails to start
with the gear engaged, the
driver is alerted of the po-
tentially dangerous situation due
to the fact that the gearbox has
automatically set to neutral by the
buzzer and the display.
SWITCHING OFF THE ENGINE
AND SYSTEM DEACTIVATION
Turning the ignition key to STOPthe en-
gine switches off: the gear selected before
turning the engine off remains engaged.
If the engine stops with the gearbox in
neutral (N), the buzzer and the blinking
of (N) draw the attention of the driver so
that the car can be put in safety conditions
engaging the first gear (1) or reverse (R).
In this case, it is necessary to turn the igni-
tion key to MARand with the brake ped-
al pressed, engage first gear (1) or reverse
(R).
NEVER leave the car with
the gears in neutral (N).
It is absolutely necessary
to turn off the engine con-
sequently deactivating the
Selespeed system keeping the brake
pedal pressed: release the pedal
ONLY when the display goes off.

GETTING TO KNOW YOUR CAR
115
Though strongly inadvisable, if due to un-
foreseen circumstances when driving down-
hill the car is allowed to travel with the gear-
box in neutral (N), when the engagement
of a gear is requested, the system auto-
matically engages the best gear to allow
transmission of the torque to the wheels in
relation to the speed of the car.
When travelling downhill with a gear en-
gaged and the accelerator released (if the
car is moving), beyond a pre-established
speed, the system engages the clutch au-
tomatically to give the car adequate engine
braking.
For safety reasons the Selespeed system
activates the buzzer when: clutch over-
heating occurs during car starting; in this
case, it is necessary to “force” moving off
avoiding hesitations or to release the accel-
erator and use the brake pedal to park the
car if the car is on a slope.Still due to safety reasons, with the car sta-
tionary, the engine running and gear (1),
(2) or (R) engaged, the system activates
the buzzer and automatically shifts to neu-
tral (N) when:
– no action is made on the accelerator
and/or brake pedals for at least 3 minutes;
– the brake is pressed for over 10 min-
utes;
– the driver’s door is opened and the ac-
celerator and brake pedal are not pressed
for at least 1.5 seconds. IMPORTANT NOTES
– With the car stopped and a gear en-
gaged always keep the brake pedal pressed
until deciding to move off;
– during prolonged halts with the engine
running it is advisable to keep the gearbox
in neutral;
– when the car is parked facing uphill, do
not use the moving off manoeuvre to keep
the car still; use the brake pedal and press
the accelerator pedal only when deciding to
move off;
– use second gear only when more con-
trol is needed for moving off manoeuvres at
low speed;
– if, with reverse gear engaged, you need
to engage first gear or vice versa, shift gear
only when the car is completely stationary
and with the brake pedal pressed.

GETTING TO KNOW YOUR CAR
116
STOPPING THE CAR
To stop the car, simply release the accel-
erator pedal and, if necessary, press the
brake pedal.
Regardless of the gear engaged and the
operating mode activated (MANUALor
CITY) the system automatically disengages
the clutch and shifts to a lower gear.
If deciding to move off again without hav-
ing stopped the car completely, the most
suitable ratio will be available for accelera-
tor again.
Stopping the car the system automatical-
ly engages first gear (1).
OPERATION
The gearbox can work according to two op-
erating modes:
– the first one is semi-automatic (MAN-
UAL): the decision to change gear is left to
the driver who decides the most appropriate
moment; this mode features the two fol-
lowing logics:
1) normal: for comfort driving;
2) sport: (to be activated by button B-
fig. 124): for sporty driving.
Sport operating mode is selected by press-
ing button SPORT(B-fig. 124) set on
the gearshift lever; when selecting this
mode, the display will show SPORT.– the second one is fully automatic
(CITY), in which the system decides di-
rectly when to shift gear according to driving
conditions.
To select the CITYmode, press button
CITYset on the gearshift lever; when se-
lecting this mode, the display will show
CITY.

GETTING TO KNOW YOUR CAR
119
In the event of whatever
transmission fault, contact
Alfa Romeo Authorized Ser-
vices as soon as possible to have
the system checked. In the event of a fault to the gearshift lever,
the system automatically activates the au-
tomaticCITYmode to allow the car to
reach the nearest Alfa Romeo Authorized
Services to have the fault detected elimi-
nated.
In the event of a fault to the other gear-
box components, the system only allows the
engagement of certain gears: first gear (1),
second gear (2) and reverse (R).
FAILURE INDICATIONS
Failures to the Selespeed gearbox are in-
dicated on the display by warning light
t
(fig. 127), dedicated message and
buzzer. If the warning light
t
and the message are dis-
played, contact Alfa Romeo
Authorized Services as soon as
possible to have the fault elimi-
nated.
fig. 127
A0A9081g

GETTING TO KNOW YOUR CAR
120
PARKING THE CAR
To park the car safely it is absolutely nec-
essary to engage first gear (1) or reverse
(R) and also the handbrake if the road is
on a slope.
Turning the engine off with the car facing
uphill and a gear engaged, it is absolutely
necessary to wait for the gear display to go
off before releasing the brake pedal, so that
the clutch is fully disengaged.
If the gearbox is in neutral (N) and want-
ing to engage a parking gear, the system
should be activated and with the foot on the
brake pedal it is necessary to engage (1)
or (R).
TOWING THE CAR
IMPORTANTFor towing the car, adhere
to local regulations. Make sure that the gear-
box is in neutral (N) (checking that the car
moves when pushed) and proceed as for
towing a normal car with mechanical gear-
box following the instructions given in sec-
tion “In an emergency”.
If setting to neutral is not possible, do not
tow the car and contact Alfa Romeo Autho-
rized Services.
While towing the car do
not start the engine.
BUZZER WARNINGS
The buzzer is activated when:
– reverse gear is engaged (R);
– the car is parked with the gearbox in
neutral (N); signal that can be noted turn-
ing the ignition key to STOP;
– clutch overheating occurs when moving
off;
– the system has shifted automatically
to neutral (N) when:
there is no action on the accelerator
and/or brake pedal for at least 3 minutes;
or the brake is pressed for over 10 min-
utes;
or the driver’s door is opened and no ac-
tion is made on the accelerator and brake
for at least 1.5 seconds;
or detection of a gearbox fault;
– gearbox fault.

IN AN EMERGENCY
180
STARTING
WITH AN AUXILIARY BATTERY
If the battery is flat (for battery with op-
tical hydrometer: dark colour without green
area in the centre), it is possible to start the
engine using an auxiliary battery with the
same capacity or a little higher than the flat
one.
Proceed as follows (fig. 1):
1) Remove the protective cover on the pos-
itive battery post pressing on the opening
catches (front), then connect the positive
terminals (+sign next to the terminal) of
the two batteries using a special cable.
2) Connect the end of the second jump
lead to the negative terminal (–) of the aux-
iliary battery with an earth point
Eon the
engine or gearbox of the car to be started.IMPORTANTDo not directly connect the
negative terminals of the two batteries: any
sparks may ignite the detonating gas which
could come out of the battery. If the auxil-
iary battery is installed on another car, avoid
metal parts touching accidentally between
this car and the one with the flat battery.
3) Start the engine.
4) When the engine has started, remove
the cables, reversing the sequence followed
for connection.
If after a few attempts the engine does not
start, do not insist but contact the nearest
Alfa Romeo Authorised Service.
fig. 1
A0A0149b
This starting procedure
must be carried out by
qualified personnel because
incorrect operations may cause
electrical discharge of considerable
intensity. The liquid contained in
the battery is poisonous and cor-
rosive. Avoid contact with the skin
and the eyes. Keep naked flames
and lighted cigarettes away from
the battery and do not cause
sparks.
Never use a battery
charger to start the engine
as this could damage the
electronic systems of your car, par-
ticularly the ignition and fuel sup-
ply control units.

CAR MAINTENANCE
219
ADDITIONAL
OPERATIONS
Every 1000 kmor before long journeys,
check and if necessary top up:
– engine coolant fluid level
– brake/hydraulic clutch control fluid level
– power steering fluid level
– windscreen washer and headlamp wash-
er fluid level
– tyre pressure and conditions.
Every 3000 kmcheck and if necessary
top up the engine oil level.
The use of FL Seleniaproducts is rec-
ommended which have been designed and
made expressly for Alfa Romeo cars (see
“Refuelling” in the “Technical Specifica-
tions” chapter).
ANNUAL INSPECTION
PROGRAMME
For cars with an annual mileage
of below 20,000 km (for example
about 10,000 km) the following
yearly inspection programme is ad-
vised:
– Check tyre conditions/wear and if nec-
essary adjust the pressure (including spare
wheel)
– Check operation of lighting system
(headlights, direction indicators, hazard
warning lights, boot, passenger compart-
ment, glovebox lights, warning lights, etc.)
– Check operation of windscreen wiper
system, spray jet adjustment
– Check windscreen blade position/wear
– Check front disk brake pad conditions
and wear
– Check cleanness of bonnet and boot
locks, and lever cleanness and lubrication.– Sight check for conditions of: engine,
gearbox, transmission, pipes (exhaust - fu-
el supply - brakes), rubber parts (boots -
sleeves - bushes etc..), brake and fuel sup-
ply system hoses
– Check battery charge
– Sight check for conditions of various dri-
ve belts
– Check and if necessary top up fluid lev-
els (engine coolant, brakes, windscreen
washer, battery etc. )
– Change engine oil and oil filter
– Change pollen filter.