engine Alfa Romeo MiTo 2010 Owner handbook (in English)

60GETTING TO KNOW YOUR CAR
REAR HEAD RESTRAINTS
Two height-adjustable head restraints are provided for the back
seats (to adjust the height see the previous paragraph). On some
versions a head restraint is also provided for the central seat.
To remove the head restraints:
❍raise the head restraint to its maximum height;
❍press button A fig. 25 and then remove the head restraint by
sliding it upwards.
STEERING WHEEL
The steering wheel can be adjusted axially and vertically.
To carry out the adjustment: release lever A-fig. 26 by pushing it
forward (position 1) and adjust the steering wheel. Then lock lever
A by pulling it towards the steering wheel (position 2).
fig. 25A0J0083mfig. 26A0J0034m
Any steering wheel position adjustment should on-
ly be carried out with the car stationary and the
engine turned off.
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 60

GETTING TO KNOW YOUR CAR65
1
PASSENGER COMPARTMENT VENTILATION
Proceed as follows to adjust the ventilation:
❍turn knob A to the blue section;
❍press button D to disable the air recirculation system (the LED
on the button should be off);
❍turn knob C to ¶;
❍turn knob B to the required speed.
CLIMATE CONTROL (cooling)
(only present on versions with manual
climate control)
Proceed as follows to cool the passenger compartment:
❍turn knob A to the blue section;
❍press button D to enable the air recirculation system (the LED
on the button should be on);
❍turn knob C to ¶;
❍press button E to switch on the climate control system and turn
knob B to at least 1 (1stspeed); to cool the passenger compart-
ment more quickly; turn knob B to 4
-(maximum fan speed).
Adjusting cooling
❍turn knob A to the right to increase the temperature;
❍press button D to disable the air recirculation system (the LED
on the button should be off);
❍turn knob B to reduce the fan speed.
WARMING THE PASSENGER COMPARTMENT
Proceed as follows:
❍turn knob A to the red section;
❍turn knob C to the desired symbol;
❍turn knob B to the required speed;
Rapid heating
Proceed as follows to rapidly heat the passenger compartment:
❍turn knob A to the red section;
❍press button D to enable the air recirculation system;
❍turn knob C to ©;
❍turn knob B to 4 -(maximum fan speed).
Then use the controls to maintain the required comfort conditions
and press button D to turn air recirculation off (button led off)
and to prevent misting up.
IMPORTANT When the engine is cold, it takes a few minutes to ob-
tain fast heating.
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 65

GETTING TO KNOW YOUR CAR73
1
CLIMATE CONTROL SYSTEM COMPRESSOR
Press button B to activate/deactivate the compressor. The deacti-
vation of the climate control compressor remains in the system
memory even when the engine has been stopped.
When the compressor is switched off the system deactivates air re-
circulation to prevent the windows from misting up. In this case,
although the system is capable of maintaining the required tem-
perature, the word FULL will disappear from the display. If, how-
ever, the system is unable to maintain the required temperature,
the temperature indication flashes and the word AUTO disappears.
IMPORTANT With the climate control compressor off, it is not pos-
sible to admit air into the passenger compartment with a temper-
ature below the outside temperature; moreover, under certain en-
vironmental conditions the windows could mist up very quickly since
the air cannot be dehumidified.
To restore automatic control for switching on the climate control
compressor, press button B again or press the AUTO button.
AIR RECIRCULATION
Air recirculation works according to the following operating logics:
❍automatic engagement: press one of the AUTO buttons. En-
gagement is indicated by the word AUTO appearing on the
display;
❍forced engagement (air recirculation always on): this is indi-
cated by the LED on button C lighting up and by the symbol
íappearing on the display;
❍forced disengagement (air recirculation always off, air drawn
from the outside): this is indicated by the LED on button C go-
ing out and by the symbol
êappearing on the display; Forced
engagement/disengagement can be selected by pressing but-
ton C.
IMPORTANT The air recirculation system makes it possible to reach
the required heating/cooling conditions faster.
It is, however, inadvisable to use it on rainy/cold days as it would
considerably increase the possibility of the windows misting up in-
side (especially if the climate control system is off).
When the outside temperature is low, recirculation is forced off (air
drawn from the outside) to prevent the windows misting up. In au-
tomatic operation, inside air recirculation is controlled automatically
by the system according to outside environmental conditions.
When manual recirculation is set, the word FULL disappears from
the display and AUTO disappears from the icon.
It is advisable not to use the air recirculation func-
tion when the outside temperature is low to pre-
vent the windows from rapidly misting up.
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 73

74GETTING TO KNOW YOUR CAR
IMPORTANT the MAX-DEF function remains on for approximately
3 minutes from the moment the engine coolant reaches a suitable
temperature.
When the function is engaged the words FULL AUTO disappear from
the display. With the function activated the only possible manual
adjustments are the regulation of the fan speed and the disen-
gagement of the heated rear windscreen.
Pressing buttons B, C, F or AUTO switches off the MAX-DEF func-
tion and restores the previous settings.
DEMISTING/DEFROSTING
OF HEATED REAR WINDSCREEN
Press button G to activate heated rear windscreen demist-
ing/defrosting. This function switches off automatically after about
20 minutes or when the engine is turned off. It is not switched
on automatically the next time the engine is started.
For versions/markets, where fitted, pressing the
(button also
activates the defrosting and defogging of the external rearview mir-
rors, the heated windscreen (where fitted) and the heated spray
nozzles (where fitted).
IMPORTANT Do not affix stickers to the inside of the rear window
over the heating filaments, to avoid damage that might cause them
to stop working properly. With climate control compressor off:
❍if the outside temperature is higher than the set one, the sys-
tem will not be able to satisfy the request. The temperature
value will then flash on the display for a few seconds and the
word AUTO will disappear;
❍the fan speed can be manually reset.
With the compressor on and the engine running, the fan speed can-
not be lower than one bar on the display.
RAPID WINDOW DEMISTING/DEFROSTING
(MAX-DEF function)
Press button F to activate rapid windscreen and side window demist-
ing/defrosting. The climate control system carries out the follow-
ing operations:
❍switches on the climate control compressor when climatic con-
ditions allow;
❍disables air recirculation;
❍sets maximum air temperature (HI) in both areas;
❍engages the fan at a speed based on the engine coolant tem-
perature;
❍directs air flow to the windscreen and front side window vents;
❍switches on the heated rear windscreen.
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 74

GETTING TO KNOW YOUR CAR75
1
ADDITIONAL HEATER
(only for diesel versions)
(for versions/markets, where provided)
This device speeds up passenger compartment warming when it is
very cold. The additional heater turns off automatically after reach-
ing the required comfort conditions.
Automatic two-zone climate control system
The additional heater is turned on automatically by turning the ig-
nition to MAR
Manual heater and manual climate
control system
The additional heater is activated automatically by turning knob
A to the end of the red section and setting the fan (knob B) to at
least the 1
stspeed.
IMPORTANT NOTES
The heater only works if the outside temperature and engine coolant
temperature are low.
The heater will not activate if the battery voltage is too low.
SWITCHING OFF THE CLIMATE
CONTROL SYSTEM
Press the OFF button. With the climate control system switched off:
❍air recirculation is on, thus isolating the passenger compartment
from the outside;
❍the compressor is off;
❍the fan is off.
❍the heated rear windscreen can be switched on or off.
IMPORTANT The climate control system control unit will store the
temperatures set before turning off and will restore them when any
button is pressed (except button G); if the function corresponding
to the button pressed is off it will be turned on; if on, it will be kept
active.
To restart the climate control system in fully automatic mode press
AUTO.
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 75

78GETTING TO KNOW YOUR CAR
EXTERIOR COURTESY LIGHTS
This function lights up the vehicle and the space around it when
the doors are unlocked.
Activation
When the vehicle is parked and the doors are unlocked by press-
ing the
Ëbutton on the remote control (or the luggage compart-
ment is unlocked by pressing
R), the dipped beam headlights,
side lights and number plate lights are activated.
The lights remain lit for approximately 25 seconds unless the doors
and luggage compartment are locked once again, the doors or lug-
gage compartment are opened and closed or the instrument pan-
el is activated. In this case they go out after 5 seconds.
The exterior courtesy lights can be enabled/disabled using the Set-
up Menu (see the paragraph on“Menu Items” in this chapter).
“FOLLOW ME HOME” DEVICE
This device allows you to illuminate the area in front of the car
for a certain amount of time.
Activation
With the ignition key on STOP or removed, pull lever A-fig. 33 to-
wards the steering wheel within 2 minutes of switching off the
engine.
The amount of time the lights remain on is extended by 30 sec-
onds at each movement of the lever, up to a maximum of 210 sec-
onds; after this the lights are switched off automatically.
The
3warning light on the instrument panel will light up (and
the corresponding message will appear on the display) as long as
the function is active.
The warning light comes on when the lever is operated and stays
on until the function is automatically deactivated. Each movement
of the lever increases the amount of time the lights stay on.
Deactivation
Keep the lever pulled towards the steering wheel for more than 2
seconds.
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 78

80GETTING TO KNOW YOUR CAR
If the vehicle is switched off with the lever in the automatic posi-
tion, when the vehicle is next started no wiping cycle will take place
even if it is raining. This is to prevent unwanted activation of the
rain sensor when the engine is started (i.e. when the windscreen
is being washed by hand or the wipers are stuck to the windscreen
by ice).
Carry out any of the following manoeuvres to restore automatic
operation:
❍move the left-hand lever from the automatic position to any
other position and then back to automatic;
❍adjust the sensitivity (by turning selector wheel A-fig. 34 to
increase or decrease).
When the rain sensor is reactivated using any of the manoeuvres
described above, reactivation is indicated by a single stroke of
the windscreen wipers, regardless of the condition of the wind-
screen. If the sensitivity of the rain sensor is adjusted whilst it is
in operation, a single stroke of the windscreen wiper takes place
to confirm the changed setting.
In the event of the malfunction of the rain sensor whilst it is ac-
tive, the windscreen wiper operates intermittently at a speed con-
sistent with the sensitivity setting of the rain sensor, regardless of
whether it is raining or not (the sensor failure is indicated on the
instrument panel display). The sensor continues to operate and it
is possible to set the windscreen wiper to continuous mode (1
stor
2ndspeed). The failure indication remains for as long as the sen-
sor is active.
RAIN SENSOR fig. 35
(for versions/markets, where provided)
This is an infra-red LED sensor fitted on the vehicle windscreen. It
is able to detect the presence of rain and consequently manage
windscreen wiping in accordance with the amount of water on
the windscreen.
Activation
The sensor is activated by turning selector wheel A-fig. 34 to the
automatic position (AUTO): in this way the windscreen wiper strokes
are regulated in accordance with the amount of water on the wind-
screen. The frequency can vary between no strokes (no rain - wind-
screen dry) and the 2
ndcontinuous speed (intense rain – wind-
screen wet).
The sensitivity of the rain sensor can be adjusted by operating se-
lector wheel A-fig. 34.
fig. 35A0J0189m
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 80

82GETTING TO KNOW YOUR CAR
INCREASING THE MEMORISED SPEED
Press the accelerator and store the new speed or move the lever
upwards (+). Each movement of the lever will correspond to a
slight reduction in speed (about 1 km/h), while keeping the lever
held downwards will reduce the speed continuously.
REDUCING THE MEMORISED SPEED
Deactivate the device and store the new speed or move the lever
downwards (–) until the new speed is reached. It will then auto-
matically be memorised. Each movement of the lever will corre-
spond to a slight reduction in speed (about 1 km/h), while keep-
ing the lever held downwards will correspond to a continuous speed
reduction.
DISENGAGING THE DEVICE
To disengage the device:
❍turn selector wheel A-fig. 36 to OFF;
❍switch off the engine;
❍press the brake pedal, the clutch or the accelerator; in this
last case the system is not effectively disengaged but the sys-
tem gives priority to the acceleration request. The device still
remains active, without the need to press the RES button to re-
turn to the previous condition once acceleration is concluded. When travelling downhill with the device engaged, the car may
slightly exceed the preset speed. When the device is activated
the
Üwarning light comes on, together with the relevant mes-
sage on the instrument panel (for versions/markets, where pro-
vided).
MEMORISING VEHICLE SPEED
Proceed as follows:
❍turn selector wheel A-fig. 36 to ON and press the accelerator
until the vehicle reaches the desired speed;
❍push the lever up (+) for at least one second and release it:
the car speed will be stored. The accelerator pedal may be re-
leased.
If needed (e.g. for overtaking), press the accelerator pedal to ac-
celerate: the car will return to the previously set speed when the
pedal is released.
RESTORING STORED SPEED
If the device has been disengaged - for example by pressing the
brake or clutch pedal - the memorised speed can be reset as fol-
lows:
❍accelerate gradually until reaching a speed approaching the one
memorised;
❍engage the gear selected at the time of speed memorising;
❍press button B-fig. 36 (RES).
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 82

84GETTING TO KNOW YOUR CAR
COURTESY LIGHT TIMING
On certain versions, two different timed switching-on modes have
been provided to facilitate getting in/out of the car at night or with
poor lighting.
Light timing when getting into the car
The courtesy lights will turn on as follows:
❍for about 10 seconds when the front doors are unlocked;
❍for about 3 minutes when one of the doors is opened;
❍for about 10 seconds when the doors are closed.
Timing is interrupted when the ignition key is turned to MAR.
Light timing when getting out of the car
After removing the key from the ignition switch, the courtesy lights
will turn on as follows:
❍within 2 minutes from turning the engine off for about 10 sec-
onds;
❍for about 3 minutes when one of the doors is opened;
❍when one of the doors is closed for about 10 seconds.
Timing will stop automatically when the doors are locked. Switch B works as a spotlight.
Switch B positions:
❍central position (position 1): lights C and D are always off;
❍pressed to the left (position 0): light C is on;
❍pressed to the right (position 2): light D is on.
IMPORTANT Before getting out of the car, make sure that both
switches are in the central position: lights off with doors closed in
order to avoid draining the battery.
In any case, if the switch is left inadvertently in the On position,
the lights will turn off automatically 15 minutes after turning the
engine off.
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 84

88GETTING TO KNOW YOUR CAR
FUEL CUT-OFF SYSTEM
This system intervenes in the event of a collision, activating:
❍switch off of fuel supply with resultant engine switch off;
❍automatic door lock release;
❍switch on of all lights inside the car.
The intervention of the system is indicated by a message shown
on the display.
Carefully check the car for fuel leaks, for instance in the engine
compartment, below the car or near the tank area.
After a collision, turn the ignition key to STOP to avoid draining the
battery.
If, after a collision, you smell fuel or notice leaks
from the fuel system, do not reset the system to
avoid fire risk.
To reset car operation, follow this procedure:
❍turn the ignition key to MAR;
❍activate the right-hand direction indicator;
❍deactivate the right-hand direction indicator;
❍activate the left-hand direction indicator;
❍deactivate the left-hand direction indicator;
❍activate the right-hand direction indicator;
❍deactivate the right-hand direction indicator;
❍activate the left-hand direction indicator;
❍deactivate the left-hand direction indicator;
❍turn the ignition key to STOP.
001-130 Alfa MiTo GB 2ed 23-12-2009 12:35 Pagina 88