ECU Acura CL 2003 Owner's Guide

CONT INUED
Panic mode will not activate if the
ignition switch is in the ON (II)
position. Panic mode allows you to remotely
activate your car’s security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will f lash, f or about 30 seconds.
To activate panic mode, press and
hold the PANIC button for about two
seconds. To turn it back on, repeat this
procedure. The LED will come on
f or one second to indicate the
f eature has been turned on.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).When the remote transmitter’s
battery begins to get weak, it may
take several pushes on the button to
lock or unlock the doors, and the
LED will not light. Replace the
battery as soon as possible.
Battery type: CR2025
To replace the battery, place a cloth
on the edge of the transmitter and
remove the upper half by carefully
prying on the edge with a small f lat-
tip screwdriver.
Replacing the Battery
Panic Mode
Keys and Locks
Inst rument s and Cont rols85

The lid of the console compartment
canbeusedasanarmrestbymoving
it f orward and backward. Make sure
the armrest is securely latched.The rear seat armrest is located at
the center of the rear seat. Pivot it
down to use it.
Make sure the passenger’s hands or
fingersareawayfromthearmrest
bef ore moving it.
Armrest
Inst rument s and Cont rols96

The pass-through cover can be
opened f rom either side; it f olds
f orward onto the center armrest.
Open the cover by sliding the knob
downward and pushing or pulling on
the cover. To close the cover, swing
it up and push f irmly on the top.
Make sure it latches properly.Make sure all items in the trunk and
those extending through the pass-
through are secured.
For security, this cover can be
locked and unlocked only with the
master key. To lock the cover, insert
thekeyandturnitclockwise.
Never drive with this cover open and
the trunk lid open.
See
on
page . 52
T runk Pass-through Cover
Carbon Monoxide Hazard
Armrest
Inst rument s and Cont rols97
K KNNO OBB
C
CO OV VE
ER
R

...............
Climate Control System . 122
.......
Fully-automatic Operation . 124
.......
Semi-automatic Operation . 125
.......
Fully-automatic Operation . 129
.......
Semi-automatic Operation . 130
Sunlight Sensor/ ............
Temperature Sensor . 134................................
Audio System .135
.................
Operating the Radio . 136
.................
Adjusting the Sound . 139
............
Audio System Lighting . 140
....................
Radio Frequencies . 140
........................
Radio Reception .140
Operating the Cassette .....................................
Player .142
............
Tape Search Functions . 143
Caring f or the Cassette .....................................
Player .146
.....
Operating the CD Changer . 147
..
Loading CDs in the Changer . 148
...................................
Operation .150
Removing CDs from the .................................
Changer .152
.......
Protecting Compact Discs . 154
CD Changer Error .............................
Indications .155
...........
Remote Audio Controls . 156
.......................
Thef t Protection .157
............................
Security System .158
...............................
Cruise Control .159
HomeLink Universal ................................
Transceiver .163
............................................
OnStar .168
3.2 CL without Navigation System
3.2 CL with Navigation System
Comf ort and Convenience Features
Comf ort and Convenience Feat ures121

The security system helps to protect
your car and valuables f rom thef t.
The horn sounds and a combination
of headlights, parking lights, side
marker lights and taillights f lashes if
someone attempts to break into your
carorremovetheradio.Thisalarm
continues f or two minutes, then the
system resets. To reset an alarming
system bef ore the two minutes have
elapsed, unlock either door with the
key or the remote transmitter.
The security system sets auto-
matically fifteen seconds after you
lock the doors, hood, and trunk. For
the system to activate, you must lock
the doors f rom the outside with the
key, lock tab, door lock switch, or
remote transmitter. The security
system light on the driver’s door
starts blinking immediately to show
you the system is setting itself .Once the security system is set,
opening either door (without using
the key or the remote transmitter),
or the hood, will cause it to alarm. It
also alarms if the radio is removed
f rom the dashboard or the wiring is
cut.With the system set, you can still
open the trunk with the remote
transmitter without triggering the
alarm. The alarm will sound if the
trunk lock is f orced, or the trunk is
opened with the trunk release button
on the driver’s door, the trunk
release handle behind the trunk
pass-through cover, or the
emergency trunk opener.
The security system will not set if
the hood, trunk, or either door is not
f ully closed. If the system will not set,
check the Door and Trunk Open
Monitor on the instrument panel
(see page ), to see if the doors
and trunk are f ully closed. Since it is
notpartofthemonitordisplay,
manually check the hood.
Do not attempt to alter this system
or add other devices to it.
63
Security System
Comf ort and Convenience Feat ures158
S SE
EC
CU UR RIITT Y
Y S
SYYSSTTE
EM
M L
LIIGGH HT
T

The HomeLink Universal
Transceiver built into your car can
be programmed to operate remotely-
controlled devices around your home,
such as garage doors, lighting, or
home security systems. It can
replaceuptothreeremote
transmitters.
If you have problems with training
the HomeLink Universal Transceiver,
or would like inf ormation on home
products that can be operated by the
transmitter, call (800) 355-3515. On
the Internet, go to www.homelink.
com.Always ref er to the operating
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with the HomeLink
Universal Transceiver. If you do not
have this inf ormation, you should
contact the manuf acturer of the
equipment.
While training or using HomeLink,
make sure you have a clear view of
the garage door or gate, and that no
one will be injured by its movement.
If you are training HomeLink to
operate a garage door or gate, it is
recommended that you unplug the
motor f or that device during training.
Repeatedly pressing the remote
control button could burn out the
motor.HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your car’s battery goes dead or is
disconnected.
If your garage door opener was
manuf actured bef ore April 1982, you
may not be able to program
HomeLink to operate it. Garage door
openers manuf actured bef ore that
date do not have a safety feature that
causes them to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury. If you
have questions, call (800) 355-3515.
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures
Customer Assistance
Important Saf ety Precautions
General Inf ormation
163

CONT INUED
Canadian Owners:
The remote control you are training
from may stop transmitting after two
seconds. This is not long enough f or
HomeLink to learn the code. Release
and press the button on the remote
control every two seconds until
HomeLink has learned the code.For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Inf ormation f rom
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so they send and
receive the correct codes.
The red light in HomeLink should
begin f lashing. It will f lash slowly
at first, then rapidly.
When the red light f lashes rapidly,
release both buttons. HomeLink
should have learned the code from
the remote control.
Plug in the garage door opener
motor, then test the HomeLink
transceiver button by pushing it. It
should operate the garage door.
If the button does not work, repeat
this procedure to train it again. If it
still does not work, you may have a variable or rolling code garage
door opener. Test this by pressing
and holding the HomeLink
transceiver button you just trained.
If the red light blinks f or two
seconds,thenstayson,youhavea
rolling code garage door opener.
You may be able to verify this with
the manufacturer’s documentation.
Go to ‘‘Training With a Rolling
Code System.’’
Repeat these steps to train the
other two HomeLink buttons to
operate any other remotely-
controlled devices around your
home (lighting, automatic gate,
security system, etc.).
5.
6.
8.
7. T raining With a Rolling Code
System
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures165

»¼
»¼µ
»¼ »¼
Say the nametag f or the number
you want to delete.
OnStar will respond with ‘‘Delete
nametag , Yes or No.’’
Say ‘‘Yes.’’
OnStar will respond with ‘‘Deleting nametag .’’
To redial
the last telephone number you
called:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Redial.’’
OnStar will respond with
‘‘Redialing,’’ then place the
telephone call.
By giving the system a security code
that you make up, you can lock out
the Personal Calling and Virtual
Advisor capabilities of the system so
unauthorized people cannot make
telephone calls. To turn security on or of f :
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Security.’’
OnStar will respond with ‘‘Enter
f our-digit security code.’’
Say the f irst digit of the code.
OnStar will repeat that digit.
OnStar will repeat that digit. Say the second digit of the code.
Say the third digit of the code.
OnStar will repeat that digit.
Say the f ourth digit of the code.
OnStar will respond with ‘‘Security
code number is now ON/OFF.’’ You must prepurchase units
(minutes) of cellular air time. The
OnStar system tracks how many
units you have remaining.
To f ind out how many units you have
remaining:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Units.’’
If you f orget the security code
entered, or someone else enters a
security code unknown to you, you
must contact an OnStar advisor to
reset the code. Press the OnStar
button, or call (888) 4-ONSTAR. OnStar will respond with ‘‘Verif y
or add.’’
Say ‘‘Verif y.’’
OnStar will respond with ‘‘You
have number units remaining.’’
Redialing a Number
Security Code K eeping T rack of Units
OnSt ar
Comf ort and Convenience Feat ures174

µAlthough Virtual Advisor can
provide inf ormation on many
subjects, you can set up a
customized prof ile with OnStar that
makes it easier to get inf ormation
about areas that are of specific
interest to you. To do this, you must
go to the OnStar web site, www.
onstar.com. This is a secure site; you
will need your account number and
PIN to access your account
inf ormation and to design your
customized prof ile. If you do not have Internet access, a
def ault prof ile can be set up f or you.
To use the Virtual Advisor f rom your
vehicle:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Virtual Advisor.’’
The system will connect you to the
Virtual Advisor. The Virtual Advisor
will prompt you f or the inf ormation
you desire.
If you would like to hear a list of
voice commands that are available,
say ‘‘Help.’’ OnStar is continually
upgrading the system, and new
commands become available.
To purchase more
units of cellular air time:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Units.’’
OnStar will respond with ‘‘Verif y
or add.’’
Say ‘‘Add.’’
OnStar will connect you to an
advisor to handle your purchase.
You can also call OnStar at (888) 4-
ONSTAR, or get inf ormation about
your account at the OnStar web site,
www.onstar.com. When you subscribe to Personal
Calling, you can also enjoy the
benef its of Virtual Advisor. This
feature lets you hear information in
your vehicle about weather, sports,
news, and stocks. It is even possible
to have your e-mail read to you. OnStar Virtual A dvisor
A dding Units
OnSt ar
Comf ort and Convenience Feat ures175

You make up and provide your
Personal Identification Number
(PIN) when you establish your
account with OnStar. You should
write down your PIN and keep it
with you at all times.
You can change your PIN at any time.
Contact the OnStar advisor by
pressing the OnStar button, or by
calling (888) 4-ONSTAR.
If you f orget your PIN, contact the
OnStar advisor. For security reasons,
your PIN will be mailed to you.OnStar uses the Global Positioning
System (GPS) to locate your vehicle
f or f unctions such as route guidance
and roadside assistance. GPS is
af f ected by structures that can
obstruct the signal, such as tunnels,
parking structures, and tall buildings.
It may not be possible f or OnStar to
pinpoint your location if you are in or
near such structures.
OnStar uses cellular technology to
communicate with your vehicle.
Cellular coverage varies by location,
which may af f ect the ability to
establish a connection, or the quality
of the connection.When you turn of f your vehicle’s
ignition, the OnStar system goes into
low-power mode. Af ter 48 hours, it
switches to sleep mode to conserve
your vehicle’s battery power.
Features such as remote door
unlocking and misplaced vehicle
assistance will not work af ter your
vehicle has been parked f or more
that 48 hours.
Personal Identif ication Number System Limitations
OnSt ar
Comf ort and Convenience Feat ures176