lock Acura CL 2003 Repair Manual

µ
µ
Î
ÎÌ
ÌÎ
Î
ÌÌ
Follow the Severe Conditions
Maintenance Schedule if you
drive your car under
one or more of the f ollowing
conditions: Driving less than 5 miles (8
km) per trip or, in f reezing
temperatures, driving less
than 10 miles (16 km) per trip.
Driving in extremely hot
[over 90°F (32°C)] conditions.
Extensive idling or long
periods of stop-and-go driving.
Trailer towing, driving with a
roof rack, or driving in
mountainous conditions.
Driving on muddy, dusty, or
de-iced roads.
Follow the Maintenance
Schedule f or Severe Conditions.
MAINLY
Maint enance
U.S. Owners
Canadian Owners
232
Visually inspect the following items: Replace every 3,750 miles (6,000 km) or 6 months
Check oil and coolant at each fuel stop
Service at the indicated
distance or time whichever
comes first.
miles x 1,000
km x 1,000
months
See dust and pollen filter on page for replacement information under special driving conditions. See timing belt on page for replacement information under special driving conditions. 120,000 miles (192,000 km) or 10 years, then every 60,000 miles
(96,000 km) or 5 years
Replace engine oil and oil filter
Check engine oil and coolant
Clean ( ) or replace ( ) air
cleaner element
Use normal schedule except in
dusty conditions
Inspect valve clearance
Replace spark plugs Replace timing belt , and inspect water pump
Inspect and adjust drive belts
Inspect idle speed
Replace engine coolant
Replace transmission fluid
Inspect front and rear brakes
Replace brake fluid
Check parking brake adjustment
Replace dust and pollen filter
Lubricate all hinges, locks, and latches
Rotate tires (Check tire inflation and condition
at least once per month)
Every 7,500 miles (12,000 km) or 6 months
Tie rod ends, steering gear box, and boots
Suspension components, Driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and condition of fluids
Cooling system hoses and connections
Exhaust system, Fuel lines and connections
Lights and controls, Vehicle underbody Rotate tires every 7,500 miles (12,000 km)
15
24
12
30
48
2445
72
3660
96
4875
120 60 90
144 72 105
168
84 120
192
96
Every 3 years (independent of mileage)
Every 7,500 miles (12,000 km) or 6 months Every 60,000 miles (96,000 km) or 3 years
See information on maintenance and
emissions warranty, last column, page.
Adjust only if noisy
Type-S
Premium model
1:
2: :
266 265 229
M/T
A/T
1
2
60,000 miles (96,000 km) or 3 years, then every 30,000 miles (48,000 km) or 2 years
Maintenance Schedule for Severe Conditions

µµ
Ø
Ø
Ø
Ø
Ø
Ø Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Î
Î
ÌÎ
Î Ì
Ì
Î
Î
Î
Î Ì
CONT INUED
Maint enance233
U.S. Owners
Canadian Owners
A, B, C, D
A
B
C
D
Refer to page to determine which schedule to use.
Use the Maintenance Schedule for Severe Conditions.
3,750 mi/6,000 km
7,500 mi/12,000 km
11,250 mi/18,000 km
15,000 mi/24,000 km/1 yr
18,750 mi/30,000 km
22,500 mi/36,000 km
26,250 mi/42,000 km
30,000 mi/48,000 km/2 yrs
33,750 mi/54,000 km
37,500 mi/60,000 km
41,250 mi/66,000 km
3yrs
45,000 mi/72,000 km/3 yrs
48,750 mi/78,000 km
52,500 mi/84,000 km
56,250 mi/90,000 km
60,000 mi/96,000 km/4 yrs
60,000 mi/96,000 km/3 yrs
63,750 mi/102,000 km
67,500 mi/108,000 km
71,250 mi/114,000 km
75,000 mi/120,000 km/5 yrs
78,750 mi/126,000 km
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time interval.
Do items in A.
Do items in A, B.
Do items in A.Clean air cleaner element.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C,D.
Do items in A.
Do items in A, B.
Do items in A. Replace brake fluid (independent of mileage).
Clean air cleaner element.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A. Replace timing belt , and inspect water pump.
DoitemsinA,B,C,D. Replace transmission fluid.
Do items in A.
Do items in A, B.
Do items in A. Clean air cleaner element.
DoitemsinA,B,C.
Do items in A. Replace engine oil and filter.
Inspect front and rear brakes.
Rotate tires (follow pattern on page
269).
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Replace air cleaner element. (Type-S)
Check parking brake adjustment.
Lubricate all hinges, locks and latches with
multipurpose grease.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect cooling system hoses and connections. Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Replace air cleaner element. (Premium model)
Inspect and adjust drive belts.
Replace dust and pollen filter .
232
See dust and pollen filter on page for replacement information under special driving
conditions. See timing belt on page for replacement information under special driving conditions.
See information on maintenance and emissions warranty, last
column, page .
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy.
NOTE:
Premium model only
1:
2:
3: :
229
266 265
1
1
2
1 3
Maintenance Schedule for Severe Conditions (listed by distance/time)

Put the radiator cap back on.
Tighten it f ully. The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Remove the radiator cap by
pushing down and turning
counterclockwise. Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system. Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents.
2.
3.
4.
5.
6.
Cooling Syst em
Maint enance244
R RE
ES
SE ER
RV V E
E T
TA
A N
NK K
R
RA A D
DI
IAA T
TO
OR R C
CAA P
P

Install a rubber hose on the drain
bolt at the rear of the engine
cylinder block. Loosen the drain
bolt.Bef ore removing the reserve tank,
remove the cruise control cable
f rom its clip, then remove the
ground cable f rom the clip on the
reserve tank. To remove the
cruise control cable, pivot the
upper part of the clip and push
down the lower part slightly.
Drain the coolant into an
appropriate container. Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant into an
appropriate container, then put the
tank back in its holder.
Af ter installing the tank back in
place, put the cables back in their
clips.
5.
4. 6.
Cooling Syst em
Maint enance246
H HO
OL LD
D E
ER
R
D
D R
RAA I
INN B
BOOL LT
T R
RU
UB BBBEER
R
H
H O
OS SEE
R
REES
SE ER
RV V E
E T
TA
A N
NK K C
CAA P
P
C
CR RUUI ISSE E C
COON NTTR
RO OL L C
CAA B
BLLE
E R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K

CONT INUED
Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Tighten the drain bolt at the rear
of the engine cylinder block
securely.
Tightening torque:
Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator up to the base of the
f iller neck. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.
The cooling system capacity is:
Start the engine and let it run f or
about 30 seconds. Then turn of f
the engine. Pour coolant into the
radiator up to the base of the f iller
neck.
7.
8.
9.10.
Cooling Syst em
Maint enance247
F FIILLL LEE R
R N
NEEC
CK K
F
F i
illll u
u p
p t
too h
he
erree R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K
7 lbf·ft (10 N·m , 1.0 kgf·m)
1.48 US gal (5.6
, 1.23 Imp gal)

Always use Honda Power Steering
Fluid. If it is not available, you may
use another power steering f luid as
an emergency replacement.
However, continued use can cause
increased wear and poor steering in
cold weather. Have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently and have
the system inspected as soon as
possible.
Check the level when the engine is
cold. Look at the side of the
reservoir. The f luid should be
between the UPPER LEVEL and
LOWER LEVEL. If it is below the
LOWER LEVEL, add power steering
f luid to the UPPER LEVEL.
The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If it is not, add
brake f luid to bring it up to that level.
Use the same fluid specified for the
brake system.
Low f luid level can indicate a leak in
the clutch system. Have this system
inspected as soon as possible. Power Steering
Clutch System
Maint enance
Brake and Clutch Fluid, Power Steering
253
U UP PP
PE
ER
R L
LEE V
V E
EL
L
L
LO OW WE ER
R L
LE
E V
V E
EL
L
M
M
A
AX
X
M
M I
INN
T urning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.

The spark plugs in your car are a
special platinum-tipped design f or
longer lif e. The spark plugs should
be replaced according to the time
and distance recommendations in
the maintenance schedule.Loosen the two holding clips by
turning the heads one-quarter turn
counterclockwise with a f lat-tipped
screwdriver. Remove the cover on
the f ront cylinder bank by pulling
it straight up.
Clean up any dirt and oil that have
collected around the ignition coils.Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
1.
2. 3.
Replacement
Spark Plugs
Maint enance256
H H
O
OL LDD I
INNG G C
CLLI
IPP I
IG
GN NIITT I
IOON N C
COOI ILL
C
CO
ON NNNEEC
CT TO
OR R
L
L O
OC CKK
T
T A
A B
B

´
µ´
µ
Install the ignition coil. Reinstall
the hexagon socket head cap bolt.
Push the wire connector onto the
ignition coil. Make sure it locks in
place.
Repeat this procedure f or the
other f ive spark plugs.
Reinstall the cover on the front
cylinder bank while putting its
mounting clip in the hole on the
passenger’s side. Secure the cover
by turning the heads of the two
holding clips one-quarter turn
clockwise with a f lat-tipped
screwdriver.
Spark Plug Gap:
Spark Plug Gap:
8.
9.
10.
11. NGK:
DENSO:
NGK:
DENSO: Specif ications:
Spark Plugs
Maint enance
Premium model
T ype-S
258
0.04 in (1.1 mm)
0.04 in (1.1 mm) PZFR5F-11
PKJ16CR-L11
PZFR6E-11
PKJ20CR-M11
0
0.1 mm0
0.1 mm
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.

µ
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or if they leave streaks
and unwiped areas when used.
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold it in while you
push the blade assembly toward
thebaseof thearm.
To replace the blade: Turn the ignition ON (II), switch
the wipers to INT or (low
position), then turn the ignition
OFF when the wiper arm is
approximately midway in its travel. Raise the wiper arm of f the
windshield.
1. 2.
3.
Wiper Blades
Maint enance262
W WIIPP E
ER
R A
AR
RMM S
S L
LO
OC CKK
T
T A
A B
B

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Turn the ignition switch ON (II)
andreturnthewindshieldwipers
to their park position. Lower the wiper arm down against
the windshield.
4. 5. 6.
7.
8.
9.
WiperBlades,AirConditioningSystem
Maint enance263
B BL
LAA D
DE
E B
BLLA
A D
DE
E
R
RE EI
INNF FOOR RCCEEM
M E
EN
NT T