reset Acura MDX 2004 Owner's Manual

Between 6,000 miles (9,600 km) and
7,500 miles (12,000 km), it will light
f or 2 seconds when you f irst turn the
ignition switch to ON (II), and then
f lash f or 10 seconds.
If you exceed 7,500 miles (12,000
km) without having the scheduled
maintenance perf ormed, this
indicator will remain on as a constant
reminder.
Your dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
done by someone other than your
Acura dealer, reset the indicator as
f ollows.
This indicator reminds you that it is
time to take your vehicle in for
scheduled maintenance.
Ref er to the Maintenance Schedules
f or Normal and Severe Driving
Conditions on pages and .
For the f irst 6,000 miles (9,600 km)
af ter the Maintenance Required
Indicator is reset, it will come on f or
2 seconds when you turn the ignition
switch to ON (II).
Turn of f the engine.
Press and hold the Select and
Reset buttons on the instrument
panel, then turn the ignition switch
to ON (II).
Hold the buttons for
approximately 10 seconds until the
indicator goes of f .
1.
2.
3.
199 200
Inst rument s and Cont rols
Instrument Panel Indicators
Maintenance Required
Indicator
65
RESET BUTTON
SELECT BUTTON

This shows the total distance your
vehicle has been driven. It measures
miles in U.S. models and kilometers
in the Canadian models.
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated.
This shows how much f uel you have.
It may show slightly more or less
than the actual amount. The needle
returns to the bottom after you turn
of f the ignition.
Gauges
Inst rument s and Cont rols
Odometer
Fuel Gauge
66
NOTICE:
TACHOMETERTEMPERATURE
GAUGE
FUEL GAUGE
SPEEDOMETER
TRIP METER RESET
BUTTON
TRIP METER
ODOMETER TRIP METER
SELECT
BUTTON
Avoid driving with an
extremely low f uel level. Running out
of f uel could cause the engine to
misf ire, damaging the catalytic
converter.

This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise to
about the middle of the gauge. In
severe driving conditions, the pointer
mayrisetotheupperwhitemark.If
it reaches the red (Hot) mark, pull
safely to the side of the road. Turn to
page f or instructions and
precautions on checking the engine’s
cooling system.
To reset a trip meter, display it, and
then press and hold the Reset button
until the number resets to ‘‘0.0’’.
Both trip meters will reset if the
vehicle’s battery goes dead or is
disconnected. There are two trip meters: Trip A
and Trip B. Switch between these
displays by pressing the Select
button repeatedly. Each trip meter
works independently, so you can
keep track of two dif f erent distances.
When you turn the ignition switch
ON (II), what you last selected is
displayed.
240
Gauges
Inst rument s and Cont rols
Trip Meter Temperature Gauge
67
SELECT BUTTON
RESET BUTTON

µ
µ
Turn the ignition switch to ON (II)
toraiseorloweranywindow.To
open the window, push the switch
downandholdit.Releasetheswitch
when you want the window to stop.
Pull back on the switch and hold it to
close the window. If the MAIN switch is OFF, the
passenger windows cannot be raised
or lowered. Keep the MAIN switch
off whenyouhavechildreninthe
vehicle so they do not injure
themselves by operating the
windows unintentionally. If the driver’s
window runs into any obstacle while
it is closing automatically, it will
reverse direction and then stop. To
close the window, remove the
obstacle, then use the window switch
again.
If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window f use is removed, the
AUTO f unction will be disabled. The
power window system needs to be
reset af ter reconnecting the battery
or installing the f use.
Start the engine. Push down and
hold the driver’s window switch
until the window is f ully open.
Pull and hold the driver’s window
switch to close the window
completely, then hold the switch
f or a second or two more.
If the power windows do not operate
properly af ter resetting, have your
vehicle checked by an Acura dealer.
The windows will operate f or up to
10 minutes af ter you turn of f the
ignition switch. Opening either f ront
door cancels this f unction. To open/close the driver’s
window, push the window switch
f irmly down or up to the second
detent, and release it. The window
will automatically go up or down all
the way. To stop the window, pull/
push on the window switch brief ly. 1.
2.
Power Windows
Inst rument s and Cont rols
AUTO REVERSE
AUTO
90
DRIVER’S WINDOW
SWITCH MAIN SWITCH
Closing a power window on
someone’s hands or fingers can
cause serious injury.
Make sure your passengers are
away from the windows before
closing them.

Playing the Radio
Comf ort and Convenience Feat ures110
SCAN BUTTON PRESET BUTTONS
PWR/VOL
KNOB
PWR/VOL
KNOBPRESET BUTTONS TUNE KNOB
TUNE KNOB
SEEK BUTTONS
PWR/VOL KNOB
SCAN BUTTONSCAN
INDICATOR
STEREO INDICATOR
AM/FM
BUTTON SEEK BAR
AM
BUTTON
STEREO
INDICATOR
FM
BUTTON
(Touring Package)
(Premium Package) (Touring Package with RES)
AM
BUTTON FM
BUTTONSEEK BUTTONS
SCAN
BUTTON PRESET BUTTONS
TUNE KNOB

µµ
´µ
µ µ
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
PWR/VOL knob. Adjust the volume
by turning the same knob.
The band and f requency that the
radio was last turned to is displayed.
To change bands, press the AM or
FM button. On the FM band, ST will
be displayed if the station is
broadcasting in stereo. Stereo
reproduction in AM is not available.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency. The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or SEEK button, then
release it.
The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station for about 5 seconds.
If you do nothing, the system will
then scan f or the next strong station
andplayitfor5seconds.Whenit
plays a station that you want to listen
to, press the SCAN button again. Each preset button can
store one f requency on AM, and two
f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Pick a preset button, and hold it
until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
stations on FM.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed.
You can use any of f ive methods to
f ind radio stations on the selected
band:
the
preset buttons, and . 1.
2.
3.
4.
CONT INUED
To Play the Radio
TUNESEEK
SCAN
Preset
To Select a Station TUNE,SEEK,SCAN, AUTO SELECT
Playing the Radio
Comf ort and Convenience Feat ures111

µµµ
µ
µ
If you are
traveling far from home and can no
longer receive your preset stations,
you can use the Auto Select f eature
to find stations in the local area.
Press the A. SEL Button. ‘‘A.SEL’’
f lashes in the display, and the system
goes into scan mode f or several
seconds. It stores the f requencies of
six AM, and twelve FM stations in
the preset buttons.
You will see a ‘‘0’’ displayed if Auto
Select cannot f ind a strong station
f or every preset button.
If you do not like the stations Auto
Select has stored, you can store
other f requencies on the preset
buttons. Use the TUNE, SEEK, or
SCAN f unction to f ind stations, then
store them in the preset buttons as
described previously. press the
A. SEL button. This restores the
presets you originally set.
Adjust the Balance, or side-
to-side strength of the sound.
Adjust the Fader, or the
f ront-to-back strength of the sound.
AdjusttheTrebleinthe
sound.
Adjust the Bass in the sound.
Push the control knob to get it to pop
out. Turn the appropriate knob to
adjust the Bass or Treble level. Pull
the knob out f arther to adjust the
FaderorBalance.Pushtheknob
back in when you are f inished. Press the TUNE knob repeatedly to
display Bass (BAS). Treble (TRE),
Balance (BAL), and Fader (FAD),
setting. Turn the TUNE knob to
adjust the setting. The indicators on
the display will show you the
adjustable range. The system will
return to the audio display in about 5
seconds.To turn of f Auto Select,
Without Touring Package With Touring Package
Playing the Radio
Comf ort and Convenience Feat ures
AUTO SELECT
Adjusting the Sound
BAL
FAD
TRE
BAS
112

µµ
´
CONT INUED
To select the CD changer, press the
CD button. The disc and track
numbers will be displayed. To select
a dif f erent disc, use the appropriate
preset buttons (1 6). On the model
with Rear Entertainment System,
use the preset 5 (DISC ) button to
select previous disc, or the preset 6
(DISC ) button to select the next
disc in sequence.
If you select an empty slot in the
magazine, the changer will, af ter
f inding that slot empty, try to load
the CD in the next slot. This
continues until it f inds a CD to load
and play. When you see LOAd in the display,
insert the disc into the CD slot.
Insert it only abut half way, the
drive will pull it in the rest of the
way. You will again see the dashes
in the display as the CD is loaded.
When LOAd appears again in the
display, insert the next disc into
the CD slot. Do not try to insert a
disc until LOAd appears. You
could damage the audio unit.
Repeat this until all six positions
are loaded. The system will then
begin playing the last CD loaded.
If you are not loading CDs into all six
positions, press the Load button
again after the last CD has loaded.
The system will begin playing the
last CD loaded.
On the lef t side of the display, the
CD Loaded indicator f or an empty
position will begin blinking. To load only one CD, press and
release the Load button. Press and hold the Load button
until you hear a beep and see
‘‘----’’inthedisplay,thenrelease
the button.
You cannot load and play 3-inch (8-
cm) discs in this system. The audio system on Touring model
has an in-dash CD changer that
holdsuptosixdiscs.
To load CDs or operate CD changer,
the ignition switch must be in the
ACCESSORY (I) or ON (II) position.
1.
2. 3.
4.
5.
On Touring Model
Comf ort and Convenience Feat ures
Operating the In-Dash CD
Changer
L oading CDs in the Changer
CD Changer
117

If you do not remove the disc f rom
the slot, the system will reload the
disc af ter 10 seconds and begin
playing it.
To remove a dif f erent CD f rom the
changer,firstselectitwiththe
appropriate preset button. When that
CD begins playing, press the eject
button.If you press the Eject button while
listening to the radio or tape, or with
the audio system turned of f , the disc
that was last selected is ejected.
Af ter that disc is ejected, pressing
the Eject button again will eject the
next disc in the numerical order. By
doing this six times, you can remove
all the CDs f rom the changer.
In any mode, if you press the eject
button and hold it until you hear a
beep, the system will eject all of the
discs in the changer.
You can also eject discs when the
ignition switch is of f . The disc that
was last selected is ejected f irst. You
can eject up to six discs, one at a
time.
To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJECT’’ in the display. The
system automatically begins the
Load sequence so you can load
another CD in that position. If you do
not load another CD, af ter 10
seconds the system begins playing
the next disc in the changer. If the
changer is empty, the system selects
the previous mode (AM, FM, or
Tape).
If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded. If you stop loading CDs bef ore all six
positions are f illed, and you do not
press the Load button, the system
will wait f or 10 seconds, then stop
the load operation and begin playing
the last CD loaded.
You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate preset
button. Select an empty position (the
CD Loaded indicator is of f ), and
press the preset button f or that
position (1 to 6). The system will
stop playing the current CD and start
the loading sequence. It will then
play the CD just loaded. Removing CDs f rom the Changer
Comf ort and Convenience Feat ures
CD Changer
118

ÛÝ
The middle button adjusts the
volume up ( ) or down ( ). Press
the top or bottom of the button and
hold it until the desired volume is
reached, then release it.
The CH button has three functions,
depending on whether you are
listening to the radio, or playing a
tape or CD.
Three controls f or the audio system
are mounted in the steering wheel
hub. These let you control basic
f unctions without removing your
hand f rom the wheel.
The MODE button changes the
audio mode between FM1, FM2, AM,
CD, and DVD/AUX (if a disc is
inserted). use the
CH button to change stations. Each
time you press this button, the
system advances to the next preset
station on the band you are listening
to. You will see the number of the
selected preset button in the display.
To change bands, or to change f rom
FM1 to FM2, press the AM/FM
button. use the CH
button to advance to the next
selection. You will see ‘‘FF’’ blinking
in the display when you press the CH
button. The system fast forwards
until it senses a silent period, then
resume playing.
the system
skips to the beginning of the next
track each time you push the CH
button. You will see the disc and
track number in the display.
If you are listening to the radio, If you are playing a tape,
If you are playing a CD,
Steering Wheel Controls
Comf ort and Convenience Feat ures128
CH BUTTON
VOLUME
BUTTON AM/FM
BUTTON