ECU Acura RL 2002 3.5 Owner's Guide

The HomeLink Universal
Transceiver built into your car can
be programmed to operate remotely-
controlled devices around your home,
such as garage doors, lighting, or
home security systems. It can
replaceuptothreeremote
transmitters.
If you have problems with training
the HomeLink Universal Transceiver,
or would like inf ormation on home
products that can be operated by the
transmitter, call (800) 355-3515. On
the Internet, go to www.homelink.
com.Always ref er to the operating
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with the HomeLink
Universal Transceiver. If you do not
have this inf ormation, you should
contact the manuf acturer of the
equipment.
While training or using HomeLink,
make sure you have a clear view of
the garage door or gate, and that no
one will be injured by its movement.
If you are training HomeLink to
operate a garage door or gate, it is
recommended that you unplug the
motor f or that device during
training. Repeatedly pressing the
remote control button could burn
out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your car’s battery goes dead or is
disconnected.
If your garage door opener was
manuf actured bef ore April 1982, you
may not be able to program
HomeLink to operate it. Garage door
openers manuf actured bef ore that
date do not have a safety feature that
causes them to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury. If you
have questions, call (800) 355-3515.
Customer Assistance
Important Saf ety Precautions General Inf ormation
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures162
01/09/28 19:50:57 31SZ3660_165

For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Inf ormation f rom
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so they send and
receive the correct codes.
The remote control you are training
from may stop transmitting after two
seconds. This is not long enough f or
HomeLink to learn the code. Release
and press the button on the remote
control every two seconds until
HomeLink has learned the code.
The red light in HomeLink should
begin f lashing. It will f lash slowly
at first, then rapidly.
When the red light f lashes rapidly,
release both buttons. HomeLink
should have learned the code from
the remote control.
Plug in the garage door opener
motor, then test the HomeLink
transceiver button by pushing it. It
should operate the garage door.
If the button does not work, repeat
this procedure to train it again. If it
still does not work, you may have a variable or rolling code garage
door opener. Test this by pressing
and holding the HomeLink
transceiver button you just trained.
If the red light blinks f or two
seconds,thenstayson,youhavea
rolling code garage door opener.
You may be able to verify this with
the manufacturer’s documentation.
Go to ‘‘Training With a Rolling
Code System.’’
Repeat these steps to train the
other two HomeLink buttons to
operate any other remotely-
controlled devices around your
home (lighting, automatic gate,
security system, etc.).
5.
6.
7.
8.
Canadian Owners:T raining With a Rolling Code
System
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures164
01/09/28 19:51:19 31SZ3660_167

The OnStarsystem in your vehicle
gives you immediate access to a wide
range of services and inf ormation
with the touch of a button. An
OnStar advisor is available 24 hours
a day, 7 days a week.
The basic Saf ety & Security Plan
provides: Press this button to contact an
OnStar advisor. You will hear a
chime, f ollowed by the
announcement, ‘‘Connecting to
OnStar.’’ The connection should take
20 to 30 seconds. The advisor will
assist you with any of the services
included in your plan.
Depending on what service you
request, you may need to give your
Personal Identification Number
(PIN) to the advisor. Your PIN is a
number you make up and provide
when you establish your OnStar
service.
If cellular telephone service is not
available in the area you are driving
in, you will hear a f ast busy signal.
The system will retry the connection
several times bef ore returning to the
ready mode.
Roadside Assistance.
Emergency Services.
Automatic Notif ication of Airbag
Deployment.
Accident Assist.
Remote Door Locking/Unlocking.
Stolen Vehicle Tracking.
Misplaced Vehicle Assistance.
The Premium Service Plan provides
these additional f eatures: Route Support.
Ride Assist.
Inf ormation and Convenience
Services.
Concierge Services. The OnStar control buttons and
indicator are located in the base of
the rear view mirror.
CONT INUED
Comf ort and Convenience Feat ures
OnStar System
OnStar Services Button
OnStar Control Panel
167
O On nS
St taar r B
BU UT TT
TO
ON N S
SY
YSSTTE
EM
M
S
ST TA
A T
TU
US S L
LIIGGH HT
T
E
E M
M E
ER
RG GE EN
NC CYY
B
BU UT TT
TO
ON N
C
CA
A L
LLL
A
A N
NS SWWE ER
R/ /E
E N
ND D
B
BU UT TT
TO
ON N
01/09/28 19:52:02 31SZ3660_170

µ
µ µ
µ
µ µ
µ
The OnStar system uses the Global
Positioning System (GPS) to locate
your vehicle whenever you place a
call. This allows the advisor to
quickly contact the nearest services
without requiring you to provide
detailed directions.
Contact
the OnStar advisor if you need
assistance with a problem (f lat tire,
out of f uel, etc.) while traveling. The
advisor will contact an appropriate
agency to come and assist you.
Contact an
OnStar advisor if you have an
emergency situation. The advisor
will contact the nearest emergency
services provider (ambulance, f ire
department, etc.) and advise them of
your situation. If you are ever in an
accident that causes the airbags to
deploy, the OnStar system
automatically places a call (provided
the OnStar system and your vehicle’s
electrical system are still intact). The
advisor will attempt to speak to you
to evaluate the situation, and contact
the nearest emergency services
provider.
The OnStar
advisor can help you if you are ever
in a minor accident by giving you a
list of inf ormation you should collect
at the accident scene.Complete,
detailed inf ormation will make it
easier to complete accident reports
and insurance claims.
By sending a signal to your
vehicle, the advisor can lock or
unlock your vehicle’s doors. This is
helpfulif youareawayfromyour vehicle and realize you f orgot to lock
the doors, or if you have locked the
keys in your vehicle. To get OnStar’s
assistance, call (888) 4-ONSTAR
(466-7827).
Using
GPS, OnStar can locate your vehicle
almost anywhere. If your vehicle is
ever stolen, contact OnStar at (888)
4-ONSTAR. The advisor will put you
in contact with the proper authorities,
and assist them with locating your
vehicle.
If you are unable to locate your
vehicleinalargeparkinglotor
parking structure, contact OnStar at
(888) 4-ONSTAR. The advisor will
remotely activate the exterior lights
and the horn, allowing you to locate
your vehicle.
Comf ort and Convenience Feat ures
OnStar System
Saf ety and Security Plan Features
Roadside Assistance
Emergency Services A utomatic Notif ication of A irbag
Deployment
A ccident A ssist
Remote Door L ocking/Unlocking
Stolen Vehicle T racking
Misplaced Vehicle Assistance
169
01/09/28 19:52:28 31SZ3660_172

»¼
»¼µ
»¼
Say the nametag f or the number
you want to delete.
OnStar will respond with ‘‘Delete
nametag , Yes or No.’’
Say ‘‘Yes.’’
OnStar will respond with ‘‘Deleting nametag .’’
To redial
the last telephone number you
called:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Redial.’’
OnStar will respond with
‘‘Redialing,’’ then place the
telephone call.
By giving the system a security code
that you make up, you can lock out
the Personal Calling and Virtual
Advisor capabilities of the system so
unauthorized people cannot make
telephone calls. To turn security on or of f :
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Security.’’
OnStar will respond with ‘‘Enter
f our-digit security code.’’
Say the f irst digit of the code.
OnStar will repeat that digit.
OnStar will repeat that digit. Say the second digit of the code.
Say the third digit of the code.
OnStar will repeat that digit.
Say the f ourth digit of the code.
OnStar will respond with ‘‘Security
code number is now ON/OFF.’’ You must prepurchase units
(minutes) of cellular air time. The
OnStar system tracks how many
units you have remaining.
To f ind out how many units you have
remaining:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Units.’’
If you f orget the security code
entered, or someone else enters a
security code unknown to you, you
must contact an OnStar advisor to
reset the code. Press the OnStar
button, or call (888) 4-ONSTAR.
CONT INUED
Comf ort and Convenience Feat ures
OnStar System
Redialing a Number
Security Code K eeping T rack of Units
173
01/09/28 19:53:49 31SZ3660_176

»¼µ
OnStar will respond with ‘‘Verif y
or add.’’
Say ‘‘Verif y.’’
OnStar will respond with ‘‘You
have number units remaining.’’
To purchase more
units of cellular air time:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Units.’’
OnStar will respond with ‘‘Verif y
or add.’’
Say ‘‘Add.’’
OnStar will connect you to an
advisor to handle your purchase. For an additional fee, you can also
enjoy the benef its of Virtual Advisor.
This feature lets you hear
inf ormation in your vehicle about
weather, sports, news, and stocks. It
is even possible to have your e-mail
read to you.
Although Virtual Advisor can
provide inf ormation on many
subjects, you can set up a
customized prof ile with OnStar that
makes it easier to get inf ormation
about areas that are of specific
interest to you. To do this, you must
go to the OnStar web site, www.
onstar.com. This is a secure site; you
will need your account number and
PIN to access your account
inf ormation and to design your
customized prof ile. If you do not have Internet access, a
default profile can be set up for you.
To use the Virtual Advisor f rom your
vehicle:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Virtual Advisor.’’
The system will connect you to the
Virtual Advisor. The Virtual Advisor
will prompt you f or the inf ormation
you desire.
If you would like to hear a list of
voice commands that are available,
say ‘‘Help.’’ OnStar is continually
upgrading the system, and new
commands become available.
You can also call OnStar at (888) 4-
ONSTAR, or get inf ormation about
your account at the OnStar web site,
www.onstar.com. A dding Units OnStar Virtual A dvisor
OnStar System
Comf ort and Convenience Feat ures174
01/09/28 19:54:08 31SZ3660_177

You make up and provide your
Personal Identification Number
(PIN) when you establish your
account with OnStar. You should
write down your PIN and keep it
with you at all times.
You can change your PIN at any time.
Contact the OnStar advisor by
pressing the OnStar button, or by
calling (888) 4-ONSTAR.
If you f orget your PIN, contact the
OnStar advisor. For security reasons,
your PIN will be mailed to you.OnStar uses the Global Positioning
System (GPS) to locate your vehicle
f or f unctions such as route guidance
and roadside assistance. GPS is
af f ected by structures that can
obstruct the signal, such as tunnels,
parking structures, and tall buildings.
It may not be possible f or OnStar to
pinpoint your location if you are in or
near such structures.
OnStar uses cellular technology to
communicate with your vehicle.
Cellular coverage varies by location,
which may af f ect the ability to
establish a connection, or the quality
of the connection.When you turn of f your vehicle’s
ignition, the OnStar system goes into
low-power mode. Af ter 48 hours, it
switches to sleep mode to conserve
your vehicle’s battery power.
Features such as remote door
unlocking and misplaced vehicle
assistance will not work af ter your
vehicle has been parked f or more
that 48 hours.
Comf ort and Convenience Feat ures
OnStar System
Personal Identif ication Number System Limitations
175
01/09/28 19:54:19 31SZ3660_178

CONT INUED
Wipe the dipstick with a clean
cloth or paper towel.
Check the engine oil level every time
you f ill the vehicle with f uel. Wait a
f ew minutes af ter turning the engine
of f bef ore you check the oil.
Remove the dipstick (orange
handle).
If you can open the hood without
sliding the hood latch handle, or the
hood latch handle moves stif f ly or
does not spring back as bef ore, the
mechanism should be cleaned and
lubricated (see page ).
Lif t the hood up most of the way.
The hydraulic supports will lif t it
uptherestof thewayandholdit
up.
To close the hood, lower it to about a
f oot (30 cm) above the f ender, then
press down f irmly with your hands.
Afterclosingthehood,makesureit
is securely latched. 2.
1.
3.
241
Service Station Procedures
Bef ore Driving
Oil Check
181
D D
I
IPP S
ST TI
ICCK K
01/09/28 19:55:12 31SZ3660_184

Store or secure all items that could
be thrown around and hurt
someone during a crash.
Besureitemsplacedonthefloor
behind the f ront seats cannot roll
under the seats and interf ere with
the driver’s ability to operate the
pedals, or with the proper
operation of the seats.
Keep the glove box closed while
driving. If the lid is open, a
passenger could injure their knees
during a crash or sudden stop.
The maximum load for your car is
850 lbs (395 kg).
Do not put any items on top of the
rear shelf . They can block your
viewandbethrownaroundthecar
during a crash.
The f inal number is the total weight
of cargo you can carry. Subtract the total f rom 850 lbs
(395 kg). If you are towing a trailer, add the
tongue weight to the number
above. Add up the weight of all occupants.
To f igure out how much cargo you
can carry: This f igure includes the total weight
of all occupants, cargo, accessories,
and the tongue weight if you are
towing a trailer. Carrying Items in the Passenger
Compartment
Load Limit
Carrying Cargo
Bef ore Driving187
Overloading or improper
loading can affect handling and
stability and cause a crash in
which you can be hurt or killed.
Follow all load limits and other
loading guidelines in this
manual.
01/09/28 19:56:15 31SZ3660_190

Make sure all windows, mirrors,
and outside lights are clean and
unobstructed. Remove f rost, snow,
or ice.
Check that the hood and trunk are
f ully closed.Check the adjustment of the
inside and outside mirrors (see
page ).
Check the adjustment of the
steering wheel (see page ).
Make sure the doors are securely
closed and locked.
Fasten your seat belt. Check that
your passengers have f astened
their seat belts (see page ).Turn the ignition switch ON (II).
Check the indicator lights in the
instrument panel.
Start the engine (see page ).
Check the gauges and indicator
lights in the instrument panel (see
page ).
Visually check the tires. If a tire
looks low, use a gauge to check its
pressure.
Check that any items you may be
carrying with you inside are stored
properly or f astened down
securely.
Youshoulddothefollowingchecks
and adjustments every day bef ore
you drive your car.
Check the adjustment of the seat
(see page ).
1.
2.
3.
4. 5.
6.
7.
8.
9.
10.
11. 12. 53
15
86
91 191
71
Preparing to Drive
Driving190
01/09/28 19:56:40 31SZ3660_193