ESP Acura RL 2004 3.5 User Guide

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Toerasethecodesstoredinallthree
buttons, press and hold the two
outside buttons until the red light
begins to f lash, then release the
buttons.
Totrainanalreadyprogrammed
HomeLink button to operate a new
device:
Select the HomeLink button you
want to train.
Press and hold the HomeLink
button until the red light begins to
f lash slowly (approximately 20
seconds).
While continuing to hold the
HomeLink button, place the
remotecontrolforthedevice2to
5inchesfromHomeLink.
Press and hold the button on the
remote control. Hold both buttons
until the red light begins to f lash
rapidly. Release both buttons. HomeLink
should now be trained to operate
the device.
Youshoulderaseallthreecodes
bef ore selling the vehicle.
1.
3. 2.
4. 5.
Erasing Codes
Retraining a Button
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures191

µOnStar will respond with ‘‘Dialing’’
andthenrepeatthecomplete
telephone number. It will then
place the telephone call.
You
must use voice commands to give
the OnStar system your calling
inf ormation. To make a phone call:
Press the Call Answer/End
(DOT) Button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Dial.’’
OnStar will respond with ‘‘Number
Please.’’
Say the f irst digit of the number.
OnStar will repeat that digit.
Always wait f or OnStar to conf irm
the digit bef ore going to the next
digit.
Say the second digit of the number.
OnStar will repeat that digit.
Continue this until you have given
OnStar the complete telephone
number. Then say ‘‘Dial.’’ When you have f inished your
conversation, press the DOT
button again to hang up.
If you make a mistake speaking a
digit of the phone number, or the
system responds with the wrong
digit, say ‘‘Clear.’’ This will cause the
system to erase the last digit.
If you need to cancel the phone call
attempt bef ore entering the
complete phone number, say ‘‘Cancel.’’
The system will cancel the operation
and return to Ready.
If the system has difficulty
understanding a voice command, it
canrespondwith:
The OnStar Personal Calling plan is
an extra-cost option that gives you
the ability to use your car’s OnStar
system as a hands-f ree cellular
telephone.
To sign up f or Personal Calling,
press the OnStar button in your car,
and notify the advisor that you’d like
to sign up. The advisor will get all
the information needed to set up
your account, and provide you with
your new cellular telephone number.
You will need to provide a credit card
number, and prepurchase ‘‘units’’ or
minutes of air time (one unit equals
one minute). Personal Calling
Placing a Telephone Call
OnSt ar
Comf ort and Convenience Feat ures196

µ
µ
µ
µ µ
To store a
telephone number and its nametag in
the system:
Press the DOT button.
Say ‘‘Store.’’ OnStar will respond with ‘‘Ready.’’
OnStar will respond with ‘‘Number
Please.’’
Say the f irst digit of the number.
OnStar will repeat that digit.
Say the second digit of the number.
OnStar will repeat that digit.
Continue this until you have given
OnStar the complete telephone
number. Then say ‘‘Store’’ again.
OnStar will respond with
‘‘Nametag Please.’’
Say the name that you want
assigned to that telephone number.
Repeat the nametag. OnStar will respond with ‘‘Again.’’
OnStar will respond with ‘‘Once
more.’’
‘‘Pardon’’ The system could not
match your voice command to one it
knows. Repeat the command
distinctly.
‘‘Slower please’’ The system
missed the command because it was
not yet ready f or it, or there was too
much background noise. Repeat the
command after a short pause.
With
voice f eedback of f , the system will
respond with a tone rather than
‘‘Ready,’’ or repeating each number
you say. Other responses will still be
by voice. To turn voice f eedback on
or of f : When someone places a telephone
call to you, the audio system will
mute and you will hear the ring.
Press the DOT button to answer the
call. When you have completed the
call, press the DOT button again to
hang up.
The OnStar system can store up to
twenty 32-digit telephone numbers in
its memory. When you store these
numbers in its memory, you give
each one a nametag. When you want
to place a telephone call, you can
recall the number by giving the
system the nametag.
OnStar will respond with ‘‘Ready.’’ Press the DOT button.
Say ‘‘Voice Feedback.’’
OnStar will respond with ‘‘Voice
feedback On/Off.’’
CONT INUED
Storing a Nametag
Voice Feedback On/Of f Incoming T elephone Calls
Using Nametags
OnSt ar
Comf ort and Convenience Feat ures197

µ
»¼ µ
»¼ µ
»¼
»¼ To redial
the last telephone number you
called:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Redial.’’
OnStar will respond with
‘‘Redialing,’’ then place the
telephone call.
By giving the system a security code
that you make up, you can lock out
the Personal Calling and Virtual
Advisor capabilities of the system so
unauthorized people cannot make
telephone calls. To turn security on
or of f :
Repeat the nametag.
OnStar will respond with ‘‘Storing
nametag .’’
To
place a telephone call using a
nametag:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Call.’’
OnStar will respond with
‘‘Nametag Please.’’
Say the nametag f or the number
you want to call.
OnStar will respond with ‘‘Callingnametag ,’’ then place the
telephone call.
If you have forgotten what nametags
you have stored, the system will read
them to you. Press the DOT button.
When the system responds with
‘‘Ready,’’ say ‘‘Directory.’’ To delete a
nametag and telephone number f rom
memory:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Delete.’’
OnStar will respond with
‘‘Nametag Please.’’
Say the nametag f or the number
you want to delete.
OnStar will respond with ‘‘Deletenametag , Yes or No.’’
Say ‘‘Yes.’’
OnStar will respond with ‘‘Deleting nametag .’’ Redialing a Number
Security Code
Placing a Telephone Call
Deleting a Nametag
OnSt ar
Comf ort and Convenience Feat ures198

µ
»¼ »¼ To purchase more
units of cellular air time:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Units.’’
OnStar will respond with ‘‘Verif y
or add.’’
Say ‘‘Add.’’
OnStar will connect you to an
advisor to handle your purchase.
You can also call OnStar at (888) 4-
ONSTAR, or get inf ormation about
your account at the OnStar web site,
www.onstar.com.
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Security.’’
OnStar will respond with ‘‘Enter
f our-digit security code.’’
Say the f irst digit of the code.
OnStar will repeat that digit.
Say the second digit of the code.
OnStar will repeat that digit.
Say the third digit of the code.
Say the f ourth digit of the code. OnStar will repeat that digit.
OnStar will respond with ‘‘Security
code number is now ON/OFF.’’
If you f orget the security code
entered, or someone else enters a
security code unknown to you, you
must contact an OnStar advisor to
reset the code. Press the OnStar
button, or call (888) 4-ONSTAR. You must prepurchase units
(minutes) of cellular air time. The
OnStar system tracks how many
units you have remaining.
To f ind out how many units you have
remaining:
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Units.’’
OnStar will respond with ‘‘Verif y
or add.’’
Say ‘‘Verif y.’’
OnStar will respond with ‘‘You
have number units remaining.’’ A dding Units
K eeping T rack of Units
OnSt ar
Comf ort and Convenience Feat ures199

You make up and provide your
Personal Identification Number
(PIN) when you establish your
account with OnStar. You should
write down your PIN and keep it
with you at all times.
You can change your PIN at any time.
Contact the OnStar advisor by
pressing the OnStar button, or by
calling (888) 4-ONSTAR.
If you f orget your PIN, contact the
OnStar advisor. For security reasons,
your PIN will be mailed to you.
Although Virtual Advisor can
provide inf ormation on many
subjects, you can set up a
customized prof ile with OnStar that
makes it easier to get inf ormation
about areas that are of specific
interest to you. To do this, you must
go to the OnStar web site, www.
onstar.com. This is a secure site; you
will need your account number and
PIN to access your account
inf ormation and to design your
customized prof ile. If you do not have Internet access, a
def ault prof ile can be set up f or you.
The system will connect you to the
Virtual Advisor. The Virtual Advisor
will prompt you f or the inf ormation
you desire.
If you would like to hear a list of
voice commands that are available,
say ‘‘Help.’’ OnStar is continually
upgrading the system, and new
commands become available.
Press the DOT button.
OnStar will respond with ‘‘Ready.’’
Say ‘‘Virtual Advisor.’’
When you subscribe to Personal
Calling, you can also enjoy the
benef its of Virtual Advisor. This
feature lets you hear information in
your car about weather, sports, news,
and stocks. It is even possible to
have your e-mail read to you.
To use the Virtual Advisor f rom your
car:Personal Identif ication Number
OnStar Virtual A dvisor
OnSt ar
Comf ort and Convenience Feat ures200

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
OnStar uses the Global Positioning
System (GPS) to locate your car f or
f unctions such as route guidance and
roadside assistance. GPS is af f ected
by structures that can obstruct the
signal, such as tunnels, parking
structures, and tall buildings. It may
not be possible f or OnStar to
pinpoint your location if you are in or
near such structures.
OnStar uses cellular technology to
communicate with your car. Cellular
coverage varies by location, which
may af f ect the ability to establish a
connection, or the quality of the
connection. When you turn of f your car’s ignition,
the OnStar system goes into low-
power mode. Af ter 48 hours, it
switches to sleep mode to conserve
your car’s battery power. Features
such as remote door unlocking and
misplaced vehicle assistance will not
work af ter your car has been parked
formorethat48hours.
OnStar
is a registered trademark of
the OnStar Corporation.
System Limitations
OnSt ar
Comf ort and Convenience Feat ures201

CONT INUED
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times. You will also see
the VSA Activation Indicator blink.When VSA activates, you will see the
VSA Activation indicator blink.
The Vehicle Stability Assist system
helps to stabilize the vehicle during
cornering if the vehicle turns more
or less than desired. It also assists
you in maintaining traction while
accelerating on loose or slippery
road surf aces. It does this by
regulating the engine’s output, and
by selectively applying braking.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
car’s entire braking system. It is still
your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety.
Driving
Vehicle Stability Assist (VSA) System
VSA A ct ivat ion Indicat or
227
VSA ACTIVATION INDICATOR

µExercise extra caution when driving
in rain af ter a long dry spell. Af ter
months of dry weather, the f irst
rains bring oil to the surf ace of the
roadway, making it slippery.
Rain, f og, and snow conditions
require a dif f erent driving technique
because of reduced traction and
visibility. Keep your car well-
maintained and exercise greater
caution when you need to drive in
bad weather. The cruise control
should not be used in these
conditions. Always drive
slower than you would in dry
weather. It takes your car longer to
react, even in conditions that may
seem just barely damp. Apply
smooth, even pressure to all the
controls. Abrupt steering wheel
movements or sudden, hard appli-
cation of the brakes can cause loss of
control in wet weather. Be extra
cautious f or the f irst f ew miles
(kilometers) of driving while you
adjust to the change in driving
conditions. This is especially true in
snow. A person can f orget some
snow-driving techniques during the
summer months. Practice is needed
to relearn those skills. Driving T echnique
Driving
Driving in Bad Weather
230

When you have washed and rinsed
the whole exterior, dry it with a
chamois or sof t towel. Letting it
air-dry will cause dulling and water
spots.
Only use the solvents and cleaners
recommendedinthisOwner’s
Manual. Frequent washing helps preserve
your car’s beauty. Dirt and grit can
scratch the paint, while tree sap and
bird droppings can permanently ruin
the f inish.
Wash your car in a shady area, not in
direct sunlight. If the vehicle is
parked in the sun, move it into the
shade and let the exterior cool down
bef ore you start. Rinse the vehicle thoroughly with
cool water to remove loose dirt.
As you dry the vehicle, inspect it f or
chips and scratches that could allow
corrosion to start. Repair them with
touch-up paint (see page ).
Check the body f or road tar, tree
sap, etc. Remove these stains with
tar remover or turpentine. Rinse it
of f immediately so it does not
harm the f inish. Remember to re-
wax these areas, even if the rest of
the vehicle does not need waxing. Wash the vehicle using the water
and detergent solution and a sof t-
bristle brush, sponge, or sof t cloth.
Start at the top and work your way
down. Rinse f requently. Fill a bucket with cool water. Mix
in a mild detergent, such as
dishwashing liquid or a product
made especially f or vehicle
washing. 301
Exterior Care
Appearance Care
Washing
300
Chemical solvents and strong cleaners
can damage the paint, metal, and
plastic on your car.