display Acura RL 2007 Manual PDF

ÛÝ
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. To exit DOOR LOCK MODE
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, and then press the
SEL/RESET button. The screen
goes back to CUSTOMIZE MENU.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the door
lock mode setup.
Multi-Inf ormation Display
128
——
y
y
(y
y

ÛÝÛÝ
When you press the LOCK button
on the remote to lock the doors and
the trunk, and then press the button
again within 5 seconds, a beeper
sounds once and the exterior lights
blink once to verif y that the doors
arelockedandthesecuritysystemis
set.
When you press the UNLOCK
button on the remote to unlock the
doors, and then press the button
again within 5 seconds, a beeper
sounds twice and the exterior lights
blink twice to verify that the doors
are unlocked and the security
system is turned of f .
To turn this feature on or off, follow
these instructions.
While the multi-information display
is in the DOOR/WINDOW SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
CONT INUED
K eyless L ock A cknowledgment
Multi-Inf ormation Display
Inst rument s and Cont rols
129
——
y
y
(y
y

ÛÝ
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
keyless lock acknowledgment setup.To exit KEYLESS LOCK
ACKNOWLEDGMENT without
changing the current setting, select
EXIT by pressing the INFO ( / )
button, then press the SEL/RESET
button. The screen goes back to
CUSTOMIZE MENU.
Multi-Inf ormation Display
130
——
y
y
(y
y

ÛÝÛÝ
When you unlock the doors by
pressing the UNLOCK button on the
remote or by grabbing the driver’s
door handle while carrying the
remote, but do not open any door the
doors relock and the security system
sets within 30 seconds. To change
the relock time, f ollow these
instructions:
While the multi-information display
is in the DOOR/WINDOW SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.Press the SEL/RESET button. The
screen changes as shown above.
Select the relock time you want (90,
60, or 30 seconds) by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
CONT INUED
Securit y Relock T imer
Multi-Inf ormation Display
Inst rument s and Cont rols
131
——
y


y
(y
y

ÛÝ
To exit SECURITY RELOCK
TIMER without changing the
current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
security relock timer setup.
Multi-Inf ormation Display
132
——
y

y
(y
y

ÛÝÛ
Ý
ÛÝ
ÛÝ
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select WIPER SETUP by
pressing the INFO ( / ) button,
th en press the SEL/RESET button.
The
changeable setting under
WIPER SETUP is called WIPER
ACTION. To get into WIPER
ACTION, do this:
Each time you press the INFO ( /
) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
WIPER ACTION, then press the
SEL/RESET button to enter your
selection.
CONTINUED
Wiper Setup
Multi-Information Display
Instru m ent sand Cont ro ls
133
Press the or button.
Press the SEL/RESET button. seepage134
——
y
y
(y
y

Û
Ý
µ
µ
You can select from these two
settings when the wiper switch is in
the INT (intermittent) position:
While the multi-information display
is in the WIPER SETUP screen of
the CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select INTERMITTENT or WITH
VEH SPD by pressing the INFO ( /
) button, then press the SEL/
RESET button to enter your
selection.
INTERMITTENT The
intermittent operation varies
according to the selection you make
on the wiper lever’s intermittent
control ring.
WITH VEH SPD The intermittent
operation varies according to vehicle
speed.
Wiper Action
Multi-Inf ormation Display
134
——
y

y
(y
y

ÛÝ
To exit WIPER ACTION without
changing the current setting, select
EXIT by pressing the INFO ( / )
button, then press the SEL/RESET
button. The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
wiper action setup.
Multi-Inf ormation Display
Inst rument s and Cont rols
135
——
y
y
(y
y

ÎÎ
Î
ÎÎ
Î
Î
Î
Î
Î
ÎTo
use the horn, press the center pad of the steering wheel.
On models with navigation system, refer to the navigation system manual.
If equipped.
Canadian
models only
1:
2:
3:
4:
Controls
Near the Steering Wheel
136
MIRROR CONTROLS PASSENGER
AIRBAG
OFF INDICATOR
HANDSFREELINK
BUTTONS
VEHICLE
STABILITY ASSIST (VSA)
SYSTEM OFF SWITCH
PADDLE
SHIFTERS
REAR WINDOW
DEFOGGER BUTTON
HEATED MIRROR
BUTTON HAZARD WARNING
BUTTON
DISTANCE BUTTON CRUISE
CONTROL
BUTTONS
SEAT HEATER SWITCHES
STEERING WHEEL
AUDIO CONTROLS
STEERING
WHEEL
ADJUSTMENTS (P.35)
INSTRUMENT
PANEL
BRIGHTNESS WINDSHIELD
WIPER/WASHER
HEADLIGHT WASHER
SWITCH
COLLISION
MITIGATION
BRAKE SYSTEM (CMBS)
OFF SWITCH
ADAPTIVE FRONT LIGHTING
SYSTEM (AFS) OFF SWITCH
VOICE CONTROL
BUTTONS HORN ADAPTIVE
CRUISE
CONTROL (ACC)
BUTTONS
SEAT HEATER AND
SEAT VENTILATION BUTTONS
(P.138)
(P.158)
(P.147) (P.237)(P.287)
(P.263) (P.178)/
(P.179)
(P.145)
(P.137) (P.145)
(P.146)/
(P.159)
(P.277)/
(P.358)
(P.307) (P.278,
283)
MULTI INFORMATION
DISPLAY BUTTONS (P.71)
(P.372)
(P.144)
(P.345)
HEADLIGHTS/
TURN
SIGNAL/FOG
LIGHTS (P.140, 142)TM
2 4
4
31
4
4
——
y
y
(y

y

Turn the fog lights on and off by
turning the switch next to the
headlight switch.
You can use the fog lights only when
the headlights are on low beam.
The headlights revert to normal
operation when you turn them on
with the switch.
Wi
th the light switch in the AUTO
position, you can also use the fog
lights when the headlights turn on
automati cally. They will go off when
the headlights turn off.
With the headlight switch off, the
high beam headlights come on with
reduced brightness when you turn
the ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch off, even if you
set the parking brake. This
feature turns off the headlights,
all other exterior lights, and the
instrument panel lights within 15
seconds after you turn the ignition
switch to the LOCK (0) position and
close the driver’s door.
To change the ‘‘HEADLIGHT AUTO
OFF TIMER’’ setting, see page . If you see a ‘‘CHECK DRL
SYSTEM’’ message on the multi-
inf ormation display, there is a
problem with the daytime running
light system. Take your vehicle to a
dealer to have it checked.
When the multi-information display
shows a ‘‘DRL OFF’’ message, the
daytime running lights are of f .
Follow the procedure in the lef t
column to turn them on. The automatic lighting of f f eature
activates if you leave the headlight
switch in the ‘‘ ’’ or ‘‘ ’’
position or if the lights are turned on
by setting the switch in the ‘‘AUTO’’
position, turn the ignition switch to
the LOCK (0) position, then open
and close the driver’s door.
If you turn the ignition switch to the
LOCK (0) position with the
headlight switch on, but do not open
the door and get out, the lights turn
of f af ter 10 minutes (3 minutes, if
the switch is in the ‘‘AUTO’’
position).
If you unlock the door, but do not
open it within 15 seconds, the lights
go of f . With the driver’s door open,
you will hear a lights-on reminder
chime. The lights turn on again when you
unlock or open the driver’s door.
118
Fog Lights
Daytime Running Lights
Automatic Lighting Of f Feature
Turn Signals and Headlights
142
——
y
y
(y
y