wheel ACURA RL 2011 Owner's Manual

This switch is at the right side of the
left vent. Press it to turn the AFS on
and off. When AFS is off, the AFS
indicator comes on as a reminder
whenyouturnontheheadlights.Here are some operating
characteristics of the AFS:
The system requires an
initialization period. It does not
begin to operate until you have
driven the vehicle a short distance.
At a stop, the right headlight turns
right when you turn the steering
wheel to the right. But the left
headlight does not turn lef t when
you turn the steering wheel to the
left.Thispreventstheleft
headlight f rom pointing at
oncoming traf f ic.
AFS is turned of f when the shif t
lever is in the R position. The AFS works with the automatic
headlight adjusting system to sense
changes in vehicle height due to
driving and loading conditions of
passengers and luggage, and adjusts
the vertical aim of the low beam
headlights automatically to
compensate f or load.
If the headlights do not seem to be
properly aimed, have the automatic
headlight adjusting system inspected
by your dealer.
When you turn the ignition switch to
the ON (II) position, the AFS is
turned on if it was on previously. AFS Of f Switch Automatic Headlight Adjusting System
A daptive Front L ighting System (A FS)
Inst rument s and Cont rols
145
AFS OFF SWITCH
10/08/04 19:05:40 31SJA660_150
ProCarManuals.com

Make any steering wheel adjustment
bef ore you start driving.Move the steering wheel in, out, up,
or down by pushing and holding the
adjustment switch in that direction.Release the switch when the
steering wheel reaches the desired
position. Make sure the steering
wheel points towards your chest, not
toward your f ace, and that you can
see the instrument panel gauges and
indicators.
Steering Wheel A djustments
148
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.
10/08/04 19:06:05 31SJA660_153
ProCarManuals.com

When you turn the ignition switch to
the LOCK (0) position and release it,
or remove the built-in key f rom the
ignition switch, the steering wheel
automatically moves f ully in and up.
Steering wheel movement is also
controlled by the driving position
memory system (see page ).
To change the ‘‘AUTO TILT &
TELESCOPIC’’ setting, see page. If your vehicle’s battery is
disconnected or goes dead, or the
f use f or the power tilt and telescopic
steering wheel is removed, the
power tilt and telescopic steering
wheel system needs to be reset
when you reconnect the battery or
install the f use.
The steering wheel returns to its
original position when you push the
ignition switch or insert the built-in
key back in the ignition switch. Push the ignition switch f or more
than 1 second and release it, or
insert the built-in key into the
ignition switch, and remove it. The
steering wheel automatically moves
f ully in and up to let you know the
system is reset.
106 164
Steering Wheel A djustments
Inst rument s and Cont rols
149
10/08/04 19:06:14 31SJA660_154
ProCarManuals.com

µµ µ
µ
You can insert or
remove the built-in key only in this
position. To turn the ignition switch
to the LOCK (0) position, the shift
lever must be in Park, and you must
push the knob or built-in key in
slightly.
If the f ront wheels are turned, the
anti-theft lock may make it difficult
to turn the ignition switch. Firmly
turn the steering wheel to the left or
right as you turn the ignition switch.
You can
operate the audio system and the
accessory power sockets in this
position. When you turn the ignition switch to
the ACCESSORY (I) position, an
‘‘ACCESSORY (I) POSITION’’
message is shown on the multi-
inf ormation display.
This is the normal
ignition switch position when driving.
Several of the indicators on the
instrument panel come on as a test
when you turn the ignition switch
f rom the ACCESSORY (I) to the ON
(II) position.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the ignition switch. If you open the driver’s door and
leave the ignition switch in the
ACCESSORY (I) or LOCK (0)
position, you will hear a reminder
beeper, and a message appears on
the multi-information display
according to the ignition switch
position. When the ignition switch is
in the ACCESSORY (I) position, a
‘‘RETURNIGNITIONSWITCHTO
LOCK (0) POSITION’’ message is
shown on the multi-inf ormation
display. When the ignition switch is
in the LOCK (0) position, a
‘‘REMOVE KEY’’ message is shown
on the multi-information display.
TheshiftlevermustbeinPark
bef ore you turn the ignition switch
knob to the LOCK (0) position or
remove the built-in key from the
ignition switch.
Ignition Switch
LOCK (0)
A CCESSORY (I)
ON (II)
ST A RT (III)
152
10/08/04 19:06:49 31SJA660_157
ProCarManuals.com

Your vehicle has a memory feature
f or the steering wheel, driver’s seat,
and outside mirror positions.
Two seat, steering wheel, and
outside mirror positions can be
stored in separate memories. You
select a memorized position by
pushing the appropriate button.
You can also select the memorized
positions by unlocking the doors
with the remote. Each remote has a
driver’s ID (see page ). The
driver’s ID (Driver 1) corresponds to
the memorized positions stored with
the memory button (1). The driver’s
ID (Driver 2) corresponds to the
memorized positions stored with the
memory button (2).Store a driving position only when
the vehicle is parked.
Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Adjust the seat to a comfortable
position (see page ).
Adjust the steering wheel to a
comf ortable position (see page ).
Adjust the outside mirrors f or best
visibility (see page ). Press the MEMO button on the
driver’s door. You will hear a beep.
The indicator in the memory
buttons (1 and 2) will blink.
Immediatelypressoneof the
memory buttons (1 or 2) until you
hear two beeps. The indicator in
the memory button will stay on.
The current positions of the
driver’s seat, steering wheel, and
outside mirrors are now stored.
1.
2.
148
174 3.
156
161
Driving Position Memory System
Storing a Driving Position in
Memory
164
MEMORY
BUTTONS MEMO BUTTON
10/08/04 19:09:10 31SJA660_169
ProCarManuals.com

Fail to press a memory button
within 5 seconds.
Readjust the seat or steering
position.
Readjust the outside mirror
position.
Turn the ignition switch out from
the ON (II) position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory.
All stored driving positions will be
lost if your vehicle’s battery goes
dead or is disconnected. To select a memorized position, do
this:
Make sure the shif t lever is in
Park.
Press the desired memory button
(1 or 2) until you hear a beep. The system will move the seat,
steering wheel, and outside mirrors
to the memorized positions. The
indicator in the selected memory
button will flash during movement.
When the adjustments are complete,
you will hear two beeps, and the
indicator will remain on.
To change the ‘‘MEMORY
POSITION LINK’’ setting, see page
.
To cancel the storing procedure
af ter pressing the MEMO button, do
any of the f ollowing:
1.
2. 104
CONT INUED
Selecting a Memorized Position
Driving Position Memory System
Inst rument s and Cont rols
165
MEMORY BUTTONS
10/09/10 19:26:46 31SJA660_170
ProCarManuals.com

To stop the system’s automatic
adjustment, do any of the f ollowing:Press any button on the control
panel: MEMO, 1, or 2.
Push any of the adjustment
switches f or the seat or steering
wheel.
Shif t out of Park.
Adjust the outside mirrors.
If you select a memorized position
without pushing the ignition switch
knob or inserting the built-in key in
the ignition switch, only the seat and
outside mirrors will adjust. To get
the system to also adjust the steering
wheel, push and turn the ignition
switch or insert the built-in key in
the ignition switch. You will hear two
beeps when it is complete. You can use the adjustment switches
to change the positions of the seat,
steering wheel, or outside mirrors
af ter they are in their memorized
position. If you change the
memorized position, the indicator in
the memory button will go out. To
keep this driving position f or later
use, you must store it in the driving
position memory.
Driving Position Memory System
166
10/08/04 19:09:34 31SJA660_171
ProCarManuals.com

If the ignition switch cannot be
turned f rom the LOCK (0) position
to the ACCESSORY (I) position afterthe beep, the steering wheel is
locked. To unlock the steering wheel,
turn it right and lef t while turning
the ignition switch at the same time.
If theremoteandthevehicledonot
recognize each other, turn the
ignition switch to the LOCK (0)
position, remove the ignition switch
cover, insert the built-in key, and
turn the switch (see pages and
).
When you push the ignition switch,
theremoteandthevehiclerecognize
each other. Af ter the recognition,
the remote indicator f lashes, and a
beeper sounds once. Af ter the beep,
turn the ignition switch.
When the remote is out of the
operating range, the ignition switch
is locked. 151
178
CONT INUED
Ignition Switch
K eyless A ccess System
Inst rument s and Cont rols
177
Make sure you know where the remote
is when you are inside the vehicle.
Remember that you can start the engine
without using the built-in key when the
remote is inside the vehicle.
Make sure you always carry the remote
with you.
10/08/04 19:12:02 31SJA660_182
ProCarManuals.com

Air conditioning, as it cools, removes
moisture from the air. When used in
combination with the heater, it
makes the interior warm and dry.Switch the f an on.
Turn on the air conditioning.
Select and fresh air mode.
Adjust the temperature to your
pref erence.
This setting is suitable f or all driving
conditions whenever the outside
temperature is above 32°F (0°C). To remove f og f rom the inside of the
windows:
Set the f an to the desired speed, or
high f or f aster def rosting.
Select . The system
automatically switches to f resh air
mode and turns on the A/C.
Adjust the temperature so the
airflow feels warm.
Select to help clear the
rear window.
To increase airf low to the
windshield, close the corner vents.
When you switch to another mode
from , the A/C setting
returns to the previous setting (on or
of f ). Select A/C, then press ENTER
on the interface selector to turn the
A/C of f if it is on. Select . The system
automatically switches to fresh air
mode and turns on the A/C.
Select .
Set the f an and temperature
controls to maximum level.
To clear the windshield f aster, you
can close the dashboard corner vents
by rotating the wheel next to it. This
sends more warm air to the
windshield def roster vents. Once the
windshield is clear, select the f resh
air mode to avoid fogging the
windows.
For your saf ety, make sure you have
a clear view through all the windows
bef ore driving.
1.
2.
3.
4.
1.
2.
3.
4.
5.1.
2.
3.
Climate Control System
Dehumidif y the Interior
T o Def og and Def rostT o Remove Exterior Frost or Ice
From the Windows
210
10/08/04 19:17:44 31SJA660_215
ProCarManuals.com

Î
Î
To pause a disc, press the
corresponding number of the
current disc on the preset buttons.
To play the disc again, press the
preset button again.
If you turn the system of f while a
disc is playing, either with the
power/volume knob or by turning
of f the ignition switch, the disc will
stay in the drive. When you turn the
system back on, the disc will begin
playing where it lef t of f . To take the system out of disc mode,
press the AM/FM button, the
DISC/AUX button, or the XM button
(If equipped). The system will switch
to the function associated with the
button you pressed. If you pressed
the DISC/AUX button, any auxiliary
input device attached to the system
will be selected. To return to disc
mode, press the DISC/AUX button
again and play will continue at the
same point it lef t of f .
The changer plays MP3/WMA discs
in recorded order. Maximum
playable file layers are 8, and total
playable tracks are 255. If your disc
has a complex structure, the changer
takessometimetoreadthedisc
bef ore beginning play. You can play a DVD-A disc in the
disc changer. The disc controls are
same as previously described.
You can also press the MODE
buttononthesteeringwheelto
change modes. To play an MP3/WMA disc, use the
disc controls previously described,
along with the f ollowing inf ormation.
: AMorFMbuttononHawaiian
models.
CONT INUED
To Pause a Disc
To Stop Playing a Disc Playing an MP3/WMA Disc Playing a DVD-A Disc
Audio System
Features
243
10/08/04 19:23:33 31SJA660_248
ProCarManuals.com