key ACURA RL 2012 Workshop Manual

The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights, parking/side marker
lights, and taillights f lash if someone
attempts to break into your vehicle
or remove the audio unit. This alarm
continues f or 2 minutes, then the
system resets. To deactivate the
system bef ore the 2 minutes have
elapsed, unlock either f ront door
with the remote or the built-in key.
The security system automatically
sets 15 seconds after you lock the
doors, close the hood, and close the
trunk. For the system to activate,
you must lock the doors f rom the
outside with the remote, built-in key,
lock tab, or master door lock switch.
The security system indicator on the
instrument panel starts blinking
immediately to show you the system
is setting itself .Once the security system sets,
opening any door, the trunk, or hood
without using the built-in key or the
keyless access remote, will cause the
alarm to activate. It also activates if
the ignition switch is turned to the
ON (II) position, the audio unit is
removed f rom the dashboard, or the
wiring is cut.
With the system set, you can still
open the trunk with the remote
without triggering the alarm. Thealarm will sound if the trunk lock is
f orced, or the trunk is opened with
the trunk release button on the
driver’s door or the emergency trunk
opener.
The security system does not set if
any door, the trunk, or hood is not
f ully closed. Bef ore you leave the
vehicle, make sure the doors, trunk
and hood are securely closed.
To see if the system sets af ter you
exit the vehicle, press the LOCK
button on the keyless access remote
within f ive seconds. If the system is
set, the horn will beep once.
Do not attempt to alter this system
or add other devices to it.
Security System
Features
315
SECURITY SYSTEM INDICATOR
11/07/20 18:40:46 31SJA670_320
ProCarManuals.com

Î
Î
CONT INUED
BluetoothHandsFreeL ink
Features
359
‘‘Change Language’’
‘‘Hands Free Help’’ ‘‘System
Set up’’
‘‘Tutorial’’‘‘Clear’’‘‘Auto Transfer’’ ‘‘Call Notification’’‘‘Security’’
‘‘Change Passcode’’
Press HFL
Talk button
Press and release the HFL Talk button each time you give a command.
: Canadian models(See page 374)
(See page 374)
(See page 374) Apply a security passcode to the system that must be input at each key
cycle to access the system
Change your security passcode
Set how you would like to be notified of an incoming call
Clear the system of all paired phones, phonebook entries and security
passcodeSet calls to automatically transfer from your phone to HFL when you
enter the vehicle
Change language from English to French
Hear a tutorial for general rules on using the system
Hear a list of available commands and additional information describing each command(See page 375)
(See page 376)
(See page 355)
(See page 355)(See page 375)
11/07/20 18:46:37 31SJA670_364
ProCarManuals.com

Press and release the HFL Talk
button bef ore a command.
Say ‘‘ .’’
If you want HFL to create a
random code each time you pair a
phone, say ‘‘ .’’ If you want
to choose your own 4-digit code to
be used each time, say ‘‘ ’’
and f ollow the HFL prompts.You can make calls using any phone
number or a name in the HFL
phonebook. You can also redial the
last number called.
Bluetooth is the wireless technology
that links your phone to HFL. HFL
uses a Class 2 Bluetooth, which
means the maximum range between
yourphoneandvehicleis30feet(10
meters).
During a call, HFL allows you to talk
up to 30 minutes af ter you remove
the key from the ignition switch.
However, this may weaken the
vehicle’s battery.Press and release the HFL Talk
button bef ore a command.
Say ‘‘ ’’ af ter the
prompts.Say ‘‘ ’’ or ‘‘ .’’
Follow the HFL prompts and say
thenamestoredintheHFL
phonebook that you want to call.
Follow the HFL prompts to
conf irm the name and make the
call. 1.
2.
3.1.
2.
3.
BluetoothHandsFreeL ink
T o change t he pairing code set t ing: T o make a call using a name in t he
HFL phonebook:
Phone setup
Random
FixedMaking a Call
Set pairing codeCall Dial
362
11/07/20 18:47:16 31SJA670_367
ProCarManuals.com

Select the name. All the phone
numbers stored f or that name will
be listed. To search f or a specif ic name in the
phonebook, enter the keyword f or
either the f irst or last name.
To display all names in the
phonebook, select the ‘‘ ’’ option.If you choose ‘‘
,’’ the phone
number will be stored in HFL, so
that you can call it using HFL’s name
tag by voice.
Select the phone number and push
the interf ace selector, HFL begins
dialing. 4.
5.
ListStore in
HandsFreeL ink
BluetoothHandsFreeL ink
364
Push up the interface selector
to show a list.
11/07/20 18:47:35 31SJA670_369
ProCarManuals.com

Select a person f rom the list. Up to
threecategoryiconsaredisplayedin
the lef t side of the list:
These indicate how many numbers
are stored for the name. If a name
has more than three category icons,
‘‘…’’ is displayed.
Select the person’s number you want
to call, and press the HFL Talk
button.You can delete any imported
phonebook.
Select ‘‘
,’’ and a list of imported
phonebooks will be displayed.
Select a phonebook you want to
delete. If the phonebook is PIN-
protected, you will need to enter the
4-digit PIN number.
To search f or a specif ic name in the
phonebook, enter the keyword f or
either the f irst or last name.
To display all names in the
phonebook, select the ‘‘ ’’ option.
CONT INUED
BluetoothHandsFreeL ink
Delet e Import ed Phonebook:
Delete Imported
Phonebook
List
Features
371
Preference
Home
Mobile
Work
PagerFax
Car
Voice
Other Push up the interface selector
to show a list.
11/07/20 18:48:55 31SJA670_376
ProCarManuals.com

Apply the parking brake.
In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery.
Make sure the shif t lever is in
Park. Press on the brake pedal. Your vehicle’s starting system has an
auto control mode. When you turn
the ignition switch to the START
(III) position, this f eature keeps the
engine’s starter motor running until
the engine starts. Follow these
instructions to start the engine:Without touching the accelerator
pedal, turn the ignition switch to
the START (III) position, then
release the ignition switch. You do
not need to hold the ignition
switch in the START (III) position
to start the engine. Depending on
the outside temperature, the
starter motor runs f or about 6 to 9
seconds until the engine starts.
If you hold the ignition switch in
the START (III) position f or more
than 7 seconds, the starter motor,
depending on the outside
temperature, runs f or about 10 to
25 seconds until the engine starts.
If the engine does not start, wait at
least 10 seconds bef ore trying
again. 1.
2.
3.4.
Starting the Engine
Driving
401
T he immobilizer system protects your
vehicle f rom thef t. If an improperly
coded key (or other device) is used, the
engine’s f uel system is disabled. For
more inf ormation, see page .
The engine is harder to start in cold
weather. Also, the thinner air f ound at
altitudes above 8,000 f eet (2,400
meters) adds to this problem.150
11/07/20 18:53:01 31SJA670_406
ProCarManuals.com

µ µIf you have done all of the above and
still cannot move the lever out of
Park, see on
page .
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. You must also press the
release button to shift into Park. The
shif t lever must be in Park bef ore
you can turn the ignition switch to
the LOCK (0) position, or remove
the built-in key f rom the ignition
switch.
Press the brake
pedal and press the release button to
shif t f rom Park to reverse. To shif t
f rom reverse to neutral, come to a
completestopandthenshift.Press
the release button bef ore shif ting
into reverse f rom neutral. To shif t f rom Park to any position,
pressfirmlyonthebrakepedal,and
press the release button on the top
of the shift lever, then move the
lever. You cannot shift out of Park
when the ignition switch is in the
LOCK (0) or ACCESSORY (I)
position.This position
mechanically locks the transmission.
Use Park whenever you are turning
of f or starting the engine. To shif t
outofPark,youmustpressonthe
brake pedal and have your foot off
the accelerator pedal. Press the
release button on the top of the shift
lever to move it.405
To shift from:
PtoR
RtoP
NtoR
DtoS
StoD
DtoN
NtoD
RtoNDo this:
Press the brake pedal, and
press the shift lever release
button.
Press the shift lever release
button.
Move the shift lever.
Automatic Transmission
Shif t L ock Release
Reverse (R) Shif ting
Park (P)
404
RELEASE BUTTON
11/07/20 18:53:22 31SJA670_409
ProCarManuals.com

µ
µ µ
CONT INUED
Use neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to the Park
position if you need to leave your
vehicle for any reason. Press on the
brake pedal when you are moving
the shift lever from neutral to
another gear.
If you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
rpm below the red zone. With the shift lever in D or S, you
canalsousethepaddleshiftersto
shif t the transmission up or down.
With the paddle shifters, you can
operate the transmission much like a
manual transmission without a
clutch pedal. For more inf ormation
on driving with the paddle shif ters,
see page .
To shift into the S
position, press the release button on
the top of the shif t lever, and move
the lever to S. This position is similar
to D, except only gears f rom f irst to
fifth are selected. (When shifting up
automatically, the vehicle speed is
higher than when in the D position.)
The S position keeps thetransmission f rom cycling between
fourth, fifth and sixth gears in stop-
and-go driving.
Use this position f or
your normal driving. The
transmission automatically selects a
suitable gear (1 through 6 gear) to
keep the engine at the best speed f or
the driving conditions.This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal and pressing the release
button does not work.
Make sure the ignition switch is in
the LOCK (0) position. Set the parking brake.
Remove the built-in key from the
keyless access remote (see page
). 1.
2.
407
181 Shif t L ock Release Neutral (N)
Engine Speed L imiter
S Position (S) Drive (D)
Automatic Transmission
Driving
405
11/07/20 18:53:32 31SJA670_410
ProCarManuals.com

If you need to use the shif t lock
release, it means your vehicle is
developing a problem. Have the
vehicle checked by a dealer.
Push down on the built-in key
while you press the release button
and move the shif t lever out of
Park to neutral.Remove the built-in key from the
shif t lock release slot, then
reinstall the cover. Make sure the
notchonthecoverisonthedriver’s
side. Press the brake pedal, and
restart the engine.
Insert the built-in key into the shift
lock release slot. Put a cloth on the edge of the shif t
lock release slot cover to prevent
scratches. Use a small f lat-tip
screwdriver or metal f ingernail f ile
to caref ully pry up the edge of the
cover and remove it from the slot. 3. 4.
5.6.
Automatic Transmission
406
COVERSHIFT LOCK RELEASE SLOT
11/07/20 18:53:39 31SJA670_411
ProCarManuals.com

Your vehicle is equipped with an
automatic headlight adjusting
system that adjusts the vertical angle
of the headlights automatically.
Refer to page for more
inf ormation.
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustments
should be done by your dealer or
another qualif ied technician.The low beam headlight bulbs are
high voltage discharge tube bulbs.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced.Your vehicle has halogen high beam
headlight bulbs which are also used
f or the daytime running light.
Handle it by its base and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth. 145
Lights
Headlight Aiming L ow Beam Headlight Bulb
ReplacementReplacing a High Beam
Headlight/Daytime Running
Light Bulb
468
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
11/07/20 19:01:37 31SJA670_473
ProCarManuals.com