Acura RSX 2005 Owner's Manual
Page 101 of 243
µ
µµ
´
Press the RPT button
to continuously play a song or
passage. You will see RPT displayed.
The track will repeat until you press
the RPT button again.
The SKIP and REPEAT
f unctions use silent periods on the
tape to find the end of a song or
passage. These f eatures may not
work if there is almost no gap
between selections, a high noise
level, or a silent period in the middle
of a selection. Thetapeplayerpicksupdirtand
oxides f rom the tape. This
contamination build up over time and
causes the sound quality to degrade.
To prevent this, you should clean the
player af ter every 30 hours of use.
Use 100-minute or shorter tapes.
Tapes longer than that may break or
jam the drive.
If the tape is loose, tighten it by
turning the hub with a pencil or your
f inger. If the label is peeling of f ,
remove it or it could cause the tape
to jam in the player. Never try to
insert a warped or damaged tape in
the player.Store tapes in their cases to protect
them f rom dust and moisture. Never
placetapeswheretheywillbe
exposed to direct sunlight, high heat,
or high humidity. If a tape is exposed
to extreme heat or cold, let it reach a
moderate temperature bef ore
inserting it into the player.
If you see the error indication
‘‘ ’’ on the display, press the
EJECT button to remove the tape
from the unit. Make sure the tape is
not damaged. If the tape will not
eject or the error indication stays on
after the tape ejects, take the vehicle
to your dealer. Never try to insert f oreign objects
into the tape player.
Press the / ( )
button to f ind the beginning of the
current song or passage. Press the /( )buttontofindthe
beginning of the next song or
passage. When the system reaches
the beginning of a song or passage, it
begins to play it. If you do not clean the tape player
regularly, it may eventually become
impossible to remove the
contamination with a normal
cleaning kit. Your dealer has a
cleaning kit available.
Type-S only
REPEATCaring f or the T ape and Player
SK IP
Playing a T ape
100
NOTE:
Page 102 of 243
Playing a CD
A ll models except T ype-ST ype-S
Features
101
CD/TAPE BUTTON
AM/FM BUTTON CD SLOTREPEAT INDICATOR
EJECT
BUTTON
RANDOM INDICATOR
SEEK/SKIP BAR
LOAD BUTTON CD SLOT
CD EJECT BUTTON
SKIP BUTTONS
REPEAT BUTTON REPEAT INDICATOR
RANDOM INDICATOR
CD BUTTON
FM BUTTON
AM BUTTON REPEAT BUTTON
RANDOM BUTTON
RANDOM BUTTON
POWER/VOLUME KNOB
POWER/VOLUME
KNOB
Page 103 of 243
´µ
´µ µ
µ
With the ignition in the
ACCESSORY (I) or ON (II) position,
insert a CD into the CD slot. The
drive will pull the CD in the rest of
the way and begin to play it. You
operate the CD player with the same
controls used f or the radio. The
number of the track playing is shown
in the display. The system will
continuously play a CD until you
change modes.
Each time you press and release
/ ( ) , the player skips
f orward to the beginning of the next
track. Press and release / ( )
to skip backward to the beginning of
the previous track. To move rapidly
within a track, press and hold the / ( ) or / ( ) . You will
see CUE or REW in the display. To continuously replay
a track, press and release the RPT
button. You will see RPT in the
display. Press the RPT button again
to turn it off.
Pressing either of the SKIP buttons
also turns of f the repeat f eature.
This f eature plays the
tracks in random order. To activate
Random Play, press and release the
RDM button. You will see RDM in
the display. This continues until you
press the RDM button again. Press the eject button ( ) to
remove the CD. If you eject the CD,
but do not remove it f rom the slot,
the system will automatically reload
the CD af ter 15 seconds and put it in
pause mode. To begin playing, press
the CD button.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the CD will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f . Press the AM/FM button to switch
to the radio while a CD is playing.
Press the CD button to play the CD.
Type-S only
CD Player
To Change Tracks (SKIP)
REPEAT
RANDOM
To Stop Playing a CD
Playing a CD
102
Page 104 of 243
To load multiple CDs in one
operation:Press and hold the Load button
until you see ‘‘LOAd’’ in the
display, then release the button.
Ontheupperleftsideof the
display, the CD number f or an
empty position will begin blinking
and the green CD Loaded
indicator will come on.
Insert the CD into the CD slot.
Insert it only about halfway; the
drive will pull it in the rest of the
way. You will see ‘‘BUSY’’ in the
display. The CD Loaded indicator
turns red and blinks as the CD is
loaded.
When LOAd appears again in the
display, insert the next CD into the
CD slot. Repeat this until all six positions
are loaded. The system will then
begin playing the last CD loaded.
If you are not loading CDs into all six
positions, press the Load button
again after the last CD has loaded.
The system will begin playing the
last CD loaded.
If you stop loading CDs bef ore all six
positions are f illed, and you do not
press the Load button, the system
will wait f or 10 seconds, then stop
the load operation and begin playing
the last CD loaded.
To load CDs or operate the CD
changer, the ignition switch must be
in the ACCESSORY (I) or ON (II)
position. Your vehicle’s audio system has an
in-dash CD changer that holds up to
six CDs, providing several hours of
continuous entertainment. You
operate this CD changer with the
same controls used f or the radio and
tape player.
Load and play only standard round
CDs. Odd-shaped CDs may jam in
the drive or cause other problems.
You cannot load and play 3-inch (8
cm) CDs in this system. 1.
2.
3.
4.5.
CONT INUED
Type-S
Operating the CD ChangerL oading CDs in t he Changer
CD Changer
Features
103
Avoid using discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.
Page 105 of 243
µ
To load a single CD:
Press and release the Load button.
When the CD number f or an
empty position starts to blink and
the green CD Loaded indicator
comeson,youwillseeLOAdin
the display. Insert the CD into the
CD slot. Insert it only about
half way, the drive will pull it in the
rest of the way.
The system will load the CD, and
begin playing it. If you press the Load button while a
CD is playing, the system will stop
playing that CD and start the loading
sequence. It will then play the CD
just loaded.
You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate preset
button. Select an empty position (the
CD Loaded indicator is of f ), and
press the preset button f or that
position (1 to 6). The system will
stop playing the current CD and start
the loading sequence. It will then
play the CD just loaded. Select the CD changer by pressing
the CD button. You will see ‘‘Cd’’ in
the display. The system will begin
playing the last selected CD in the
CD changer. You will see the CD and
track numbers displayed.
When that CD ends, the next CD in
the CD changer is loaded and played.
Af ter the last CD f inishes, the
system returns to CD 1.
To select a dif f erent CD, press the
appropriate Preset button (1 6). If
youselectanemptypositioninthe
CD changer, the system will go into
the loading sequence (see page ).
You can use the SKIP buttons while
a CD is playing to select passages
and change tracks.
1.
2.
3.
103
Operat ion
CD Changer
104
Page 106 of 243
Ó
ÓÓÓ µ
µ´
µ ´µ
To move rapidly within a track, press
and hold the appropriate SKIP
button. You will hear a beep and the
system will continue to move. Press
the button to move forward, or
the button to move backward.
Release the button when the system
reaches the point you want.
Each time you press the button
and release it, the system skips
f orward to the beginning of the next
track. Press and release the
buttontoskipbackwardtothe
beginning of the current track. Press
and release it again to skip to the
beginning of the previous track. To activate the Repeat
f eature, press and release the RPT
button. You will see RPT in the
display as a reminder. The system
continuously replays the current
track. Press the RPT button again to
turn it off. Pressing either of the
SKIP buttons also turns off the
repeat feature.
This feature,
when activated, plays the tracks
within a CD in random order, rather
than in the order they are recorded
on the CD. To activate Random Play,
press the RDM button. You will see
RDM in the display. The system will
then select and play tracks randomly.
This continues until you deactivate
RandomPlaybypressingtheRDM
button again, or you select a
dif f erent CD with a preset button. To take the system out of CD mode,
press the AM or FM button, or insert
a tape in the player. If a tape is
already in the tape player, press the
TAPE button. When you return to
CD mode by pressing the CD button,
play will continue at the same point
that it lef t of f .
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or the ignition switch, play will
continue at the same point when you
turn it back on.
CONT INUED
REPEAT
RANDOM PLAY
CD Changer
Features
105
Page 107 of 243
To remove the CD that is currently
playing, press the eject button. You
will see ‘‘EJEC’’ in the display. When
you remove the CD f rom the slot,
the system automatically begins the
Load sequence so you can load
another CD in that position. If you do
not load another CD, af ter 10
seconds the system begins playing
the next CD in the changer. If the
changer is empty, the system selects
the previous mode (AM, FM, or
Tape).
If you do not remove the CD f rom
the slot, the system will reload the
CD af ter 15 seconds and put the CD
changer in pause mode. To begin
playing the CD, press the CD button.
To remove a different CD from the
changer,firstselectitwiththe
appropriate preset button. When that
CD begins playing, press the eject
button.If you press the Eject button while
listening to the radio or tape, or with
the audio system turned of f , the CD
that was last selected is ejected.
After that CD is ejected, pressing the
Eject button again will eject the next
CD in the numerical order. By doing
this six times, you can remove all the
CDs f rom the changer.
In any mode, if you press the eject
button and hold it until you hear a
beep, the system will eject all of the
CDs in the changer.
You can also eject CDs when the
ignition switch is of f . The CD that
was last selected is ejected f irst. You
can eject up to six CDs, one at a time.
Removing CDs f rom t he Changer
CD Changer
106
Page 108 of 243
µ´
To select the CD changer, press the
CD button. The CD and track
numbers will be displayed. To select
a dif f erent CD, use the preset 5
(DISC ) or preset 6 (DISC )
button. If you select an empty slot in
the magazine, the changer will, af ter
f inding that slot empty, try to load
the CD in the next slot.
Load the desired CDs in the
magazine, and load the magazine in
the changer according to the
instructions that came with the unit. A CD changer is available f or your
vehicle. It holds up to six CDs. You
operate the CD changer with the
same controls used f or the in-dash
CD player.
Optional on all models except Type-S
Operating the Optional CD
Changer
CD Changer
Features
107
Page 109 of 243
When using CD-R discs, use only
high quality CDs labeled f or audio
use.
When recording a CD-R, the
recording must be closed f or it to
be used by the CD player or
changer.
CD-RW discs will not work in this
unit.
Play only standard round CDs.
Odd-shaped CDs may jam in the
driveorcauseotherproblems.When a CD is not being played, store
it in its case to protect it f rom dust
and other contamination. To prevent
warpage, keep CDs out of direct
sunlight and extreme heat.
To clean a CD, use a clean sof t cloth.
Wipe across the CD f rom the center
to the outside edge.
AnewCDmayberoughonthe
inner and outer edges. The small
plastic pieces causing this roughness
can f lake of f and f all on the re-
cording surf ace of the CD, causing
skipping or other problems. Remove
these pieces by rubbing the inner
and outer edges with the side of a
pencil or pen.
Never try to insert f oreign objects in
the CD player or the magazine.
Handle a CD by its edges; never
touch either surf ace. Do not place
stabilizer rings or labels on the CD.
These, along with contamination
f rom f ingerprints, liquids, and f elt-tip
pens, can cause the CD to not play
properly, or possibly jam in the drive.
Handle your CDs properly to
prevent damage and skipping.
Protecting Your CDs
General Inf ormation
Protecting CDs
108
Page 110 of 243
Message Cause
If you see an error message in the
display while playing a CD, f ind the
cause in the chart to the right. If you
cannot clear the error message, take
your vehicle to your dealer. Solution
FOCUS error.
Mechanical error.
High temperature.Press the EJECT button and pull out the CD.
Check if it is inserted correctly in the CD player.
Make sure the CD is not scratched or damaged.
Press the EJECT button and pull out the CD.
Check the CD for damage or deformation.
If the CD cannot be pulled out or the error
message does not disappear after the CD is
ejected, consult your dealer.
Will disappear when the temperature returns to
normal.
All models except Type-S
CD Player Error Messages
Features
109