Acura TL 2003 3.2 Owners Manual

µ
Pull up or push down on the f ront of
the switch to move the seat bottom’s
f ront edge up or down. Pull up or
push down on the rear of the switch
to move the rear of the seat bottom
up or down.
Push the horizontal switch forward
or backward to move the seat
forward or backward.
You can adjust the seat with the
ignition switch in any position. Make
all adjustments bef ore you start
driving. The two power seat adjustment
switches are on the outside edge of
the seat bottom. The horizontal
switch adjusts the seat bottom in
several directions. The short vertical
switch adjusts the seat-back angle.
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs. 1413
Driver’s Seat Full Power
Adjustments
Seat A djustments
Inst rument s and Cont rols88

Pull the center of the horizontal
switch up to raise the seat. Push it
down to lower the seat.Adjust the seat-back angle by
pushing the rear switch in the
direction you want to move.The driver’s seat includes a memory
f eature. Two seat positions can be
stored in separate memories. You
canthenselectamemorizedposition
by pushing the appropriate memory
button or using the remote
transmitter. Refer to page for
how to memorize and select seat
positions.
96
Seat A djustments
Inst rument s and Cont rols89

µ
The seat adjustment switches are on
the outside edge of the seat bottom.
Push the long horizontal switch
forward or backward to move the
seat bottom in that direction.
Adjust the seat-back angle by
pushing the vertical switch in the
direction you want to move.
Vary the lumbar support by moving
the lever on the right side of the
seat-back. Move the lever forward or
backward to adjust the lumbar
support through its f ull range. Make all seat adjustments bef ore
you start driving.
You can adjust the seat with the
ignition switch in any position.
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs. 13 14
Driver’s L umbar Support
Front Passenger’s Seat
Adjustments
Inst rument s and Cont rols
Seat A djustments
90

To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button
and pull the restraint out of the seat-
back.
The f ront head restraints help
protect you and your passenger f rom
whiplash and other injuries. They are
most ef f ective when you adjust them
so the back of the occupant’s head
rests against the center of the
restraint. A taller person should
adjust the restraint as high as
possible. The head restraints adjust f or height.
On Premium models, it adjusts f or
tilt. You need both hands to adjust
the restraint. Do not attempt to
adjust it while driving. To raise it,
pull upward. To lower the restraint,
push the release button sideways
and push the restraint down. To
adjust the tilt, pivot the head
restraint to the desired position.
See page f or important saf ety
inf ormation and a warning about how toproperly position the head restraints. 15
Seat A djustments
Inst rument s and Cont rols
Head Restraints
91
R RE
EL
LEE A
A S
SEE B
BUUT TT
TO
ON N

The rear seat armrest is located in
the center of the rear seat. Pivot it
down to use it.
Make sure the passenger’s hands or
fingersareawayfromthearmrest
bef ore moving it.
The lid of the console compartment
canbeusedasanarmrestbymoving
it f orward and backward. Make sure
the armrest is securely latched.
Inst rument s and Cont rols
Armrest
92

The pass-through cover can be
opened f rom either side; it f olds
f orward onto the center armrest.
Open the cover by sliding the knob
downward and pushing or pulling on
the cover. To close the cover, swing
it up and push f irmly on the top.
Make sure it latches properly.Make sure all items in the trunk and
those extending through the pass-
through are secured.
For security, this cover can be
locked and unlocked only with the
master key. To lock the cover, insert
thekeyandturnitclockwise.
Never drive with this cover open and
the trunk lid open.
See
on
page . 53
Inst rument s and Cont rols
T runk Pass-through Cover
Carbon Monoxide Hazard
Armrest
93
K KNNO OBB
C
CO OV VE
ER
R

Adjust the outside mirrors with the
adjustment switch on the driver’s
door armrest:Turn the ignition switch ON (II).
Move the selector switch to L
(driver’s side) or R (passenger’s
side).
Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this sensing.1.
2.
Inst rument s and Cont rols
Mirrors
Adjusting the Power Mirrors
94
S SE
EL
LEE C
CT TO
OR R S
SWWI ITT C
CH H
S
SE
EN
NS SOOR R
I
IN ND DI
ICCA A T
TO
OR R
A
AU
UT TO
O B
BUUT TT
TO
ON N
I
IN
ND DI
ICCA A T
TO
OR R
W
Wi
itth h O
OnnS
St taar r
W
Wi itth h o
ou
ut
t O
On nS
St taar r A
A
U
UT TO
O B
BUUT TT
TO
ON N
S
SE EN
NS SOOR R

Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.When you f inish, move the
selector switch to the center (off)
position. This turns of f the
adjustment switch so you can’t
move a mirror out of position by
accidentally bumping the switch.
With the selector switch in the
center (of f ) position, the passenger’s
side mirror will pivot downward
slightly when you shif t the
transmission into reverse. This will
give you a better view of that side of
the vehicle while parallel parking.
The mirror returns to its original
position when you take the
transmission out of reverse.
Outside mirror positions can be
stored in the driving position
memory system (see page ). The outside mirrors are heated to re-
move fog and frost. With the ignition
switchON(II),turnontheheaters
by pressing the button. The light in
the button comes on as a reminder.
Press the button again to turn the
heaters of f .
3. 4.
96
Mirrors
Inst rument s and Cont rols95
A AD
DJ
JUUS STTM
M E
EN
NT T S
SWWI ITT C
CH H H
H
E
EA
A T
TE
ED
D M
MI
IRRR ROOR R B
BUUT TT
TO
ON N

Turn the ignition switch ON (II).
You cannot add a new driving
position in the memory unless the
ignition switch is ON (II). You can
recall a memorized position with
the ignition switch in any position.
Store a driving position as explained
in this section only when the car is
parked.
Your Acura has a memory f eature
f or the driver’s seat and outside
mirror positions.
Two seat and outside mirror
positions, f or dif f erent drivers or
drivingconditions,canbestoredin
separate memories. You select a
memorized position by pushing the
appropriate button or using the
appropriate remote transmitter
(Memory1orMemory2).
Adjust the seat to a comfortable
position (see page ).
Adjust the outside mirrors f or best
visibility (see page ).Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator light in the
memory button will come on. The
current positions of the driver’s
seat and outside mirrors are now
stored.
3.
1.
2.
88
94
St oring a Driving Posit ion in Memory
Driving Posit ion Memory Syst em
Inst rument s and Cont rols96
M M E
EM
M O
O B
BUUT TT
TO
ON N

Not pressing a memory button
within 5 seconds.You can select memorized positions
as f ollows.Make sure the parking brake is set
and the shif t lever is in Park.
Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.
Readjusting the seat position.
Readjusting the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button.
All stored driving positions will be
lost if your car’s battery goes dead or
is disconnected. Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.The system will move the seat and
outside mirrors to the memorized
positions. The indicator light in the
selected memory button will f lash
during movement. When the
adjustments are complete, you will
hear two beeps and the indicator
light will remain on.
1.
2.
CONT INUED
Select ing a Memorized Posit ion
Driving Posit ion Memory Syst em
Inst rument s and Cont rols97
M M E
EM
M O
ORRYY B
BUUT TT
TO
ON NSS