lights Acura TL 2003 3.2 Service Manual

Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Push the electrical connector onto
the new bulb. Turn on the f ront
f og lights to test the new bulb.
Put the light assembly into the
bumper. Tighten the mounting
bolt.
Remove the light assembly f rom
the bumper. Use a wrench to loosen the light
assembly’s mounting bolt.
Your car uses halogen f og light
bulbs. See page f or inf ormation
on replacing a halogen bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise. Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.5.
6.
7.
1.
2. 3.
4.
269
Lights
Maint enance
ReplacingaFogLightBulb
272
M M
O
OUUNNTTI
INNG G B
BOOL LTT B
BU
UL LBB C
COON NNNEEC
CT TO
OR R

Determine which of the f our bulbs
is burned out: stop/taillights, turn
signal light, or back-up light.
Remove the socket by turning it
one-quarter turn counterclockwise.
Open the trunk.
Remove the f astener on the edge
of the trunk opening by turning it
counterclockwise with a coin.
Unscrew the cargo net mounting
button. Pull the lining back.
Screw the cargo net mounting
button back into the hole. Put the f astener in the hole on the
side of the trunk lining and push
on the center until it locks (the
center is f lush with the head). Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal. Testthelightstomakesurethe
new bulb is working. Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
To remove the turn signal bulb
push it in slightly and turn it
counterclockwise. To remove the
stop/taillight or back-up light, pull
the bulb straight out of its socket. Install the new bulb into the
socket.
3. 2.
4. 5.
6.
7.
8.
9.
1.
10.
Lights
Maint enance
Replacing Rear Bulbs
273
F FAA S
STTE
EN
NE ER
R
C
CA
A R
RGGO O N
NEET
T M
M O
OUUNNTTI
INNG G
B
BU UT TT
TO
ON N

Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb and reinstall
the socket. Make sure the new
bulb is working.Use a small Phillips-head
screwdriver to remove the two
screws. Remove the lens f rom the
license plate assembly.
Remove the bulb by pulling it
straight out. Push the new bulb
into the socket.Put the lens back in place and
tighten the two screws securely.
1. 2.
3. 1.
2.3.
Replacing a High-mount Brake
Light Bulb Replacing a Rear License Plate
Bulb
Lights
Maint enance274

CONT INUED
The ceiling light, door light and
vanity mirror light come apart the
same way, but they do not use the
same type of bulb.Remove the bulb by pulling it
straight out of its metal tabs.
Push the new bulb into the metal
tabs. Snap the lens back in place.
Removethelensbycarefully
prying on the edge of the lens with
a f ingernail f ile or a small f lat-tip
screwdriver. Do not pry on the
edge of the housing around the
lens.
Door light:Pry on the top middle of the lens.
Ceiling light: Pry on the f ront edge of the lens
near both sides.
Spotlights: Pry on the front edge in front of
both spotlights.
1.
2.
3.
Maint enance
Lights
Replacing Bulbs in the Interior
Lights
275
C CEEI
ILLI INNG G L
LIIGGH HT
T S
SPPO
OT TL
LIIGGH HT
TS
S

Open the trunk. Pull down the
trunk light cover.
Remove the bulb by pulling it
straight out of its metal tabs.
Push the new bulb into the metal
tabs.
Push the cover back in place.
1.
2.
3.
4.
Lights
Maint enance
Replacing the T runk L ight Bulb
276
D D
O
OO ORR L
LIIGGH HT
T
T
TR
RU UN NKK L
LIIGGH HT
T
V
V
A
AN
NI ITT Y
Y M
M I
IRRR ROOR R L
LIIGGH HT
T

If you have a f lat tire while driving,
stop in a saf e place to change it.
Stopping in traf f ic or on the shoulder
of a busy road is dangerous. Drive
slowly along the shoulder until you
gettoanexitoranareatostopthat
is far away from the traffic lanes.Open the trunk. Raise the trunk
f loor by lif ting up on the back edge.
To keep the trunk f loor out of the
way, attach the hook into the slot
in the trunk lid.
The tools are in the tool box on
the right side of the trunk. Take
the tools out of the tool box. Unscrew the wing bolt and take
the spare tire out of its well.
Park the car on f irm, level, and
non-slippery ground away f rom
traffic. Put the transmission in
Park. Apply the parking brake.
If you are towing a trailer, unhitch
the trailer.
Turn on the hazard warning lights
and turn the ignition switch to
LOCK (0). Have all the
passengers get out of the car while
you change the tire. 5. 4. 3.
2. 1.
CONT INUED
Changing a Flat T ire
T aking Care of t he Unexpect ed289
T T
O
OO OLL B
BOOX X
H
H
O
OO OKK T
T
R
RU UN NKK F
FLLOOO ORR
S
SP PA
A R
REE T
TI
IRRE E J
JA
A C
CKK
The car can easily roll off the
jack, seriously injuring anyone
underneath.
Follow the directions for
changing a tire exactly, and
never get under the car when it
is supported only by the jack.

When you turn the ignition switch to
START (III), you do not hear the
normal noise of the engine trying to
start. You may hear a clicking sound
or series of clicks, or nothing at all.
Check these things:
Diagnosing why your engine won’t
start f alls into two areas, depending
on what you hear when you turn the
key to START (III):
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
f aster than normal, but the engine
does not start up and run. Check the transmission interlock.
The transmission must be in Park
orNeutralorthestarterwillnot
operate.
Turn the ignition switch to ON (II).
Turn on the headlights and check
their brightness. If the headlights
are very dim or don’t light at all,
the battery is discharged. See
on page . Turn the ignition switch to START
(III). If the headlights do not dim,
check the condition of the f uses. If
the f uses are OK, there is proba-
bly something wrong with the
electrical circuit f or the ignition
switch or starter motor. You will
need a qualif ied technician to
determine the problem. (See
on page .)
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is dis-
charged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page ). You can
then try jump starting the car from
a booster battery (see page ).
296 312
253 296
If Your Engine Won’t Start
T aking Care of t he Unexpect ed
Nothing Happens or the Starter
Motor Operates Very Slowly
Jump Starting Emergency T owing
295

µ
´ ´
CONT INUED
Connect the second jumper cable
to the negative ( ) terminal on
the booster battery. Connect the
other end to the grounding strap
as shown. Do not connect this
jumper cable to any other part of
the engine.
Remove the battery cover.
To jump start your car, f ollow these
directions closely:
Open the hood and check the
physical condition of the battery
(see page ). In very cold
weather, check the condition of
the electrolyte. If it seems slushy
or like ice, do not try jump starting
until it thaws.
Turn of f all the electrical acces-
sories: climate control, stereo
system, lights, etc.
Put the transmission in Neutral or
Park, and set the parking brake. Connect one jumper cable to the
positive ( ) terminal on your
Acura’s battery. Connect the other
end to the positive ( ) terminal
on the booster battery.
4.
5.
3.
1.
2. 253
Jump Starting
T aking Care of t he Unexpect ed297
P P
r
reem m i
iuu m
m m
mo
od
de
ell
If a battery sits in extreme cold, the
electrolyte inside can f reeze.
Attempting to jump start with a f rozen
battery can cause it to rupture.

Turn the ignition switch to LOCK
(0). Make sure the headlights and
all other accessories are off.
Remove the cover f rom the f use
box.Check each of the large f uses in
the under-hood f use box by
looking through the top at the wire
inside. Removing these f uses
requires a Phillips-head screw-
driver.
Check the smaller f uses in the
under-hood f use box and all the
fuses in the interior fuse boxes by
pulling out each f use with the f use
puller provided in the under-hood
fuse box.
If something electrical in your car
stops working, the f irst thing you
should check f or is a blown f use.
Determine f rom the chart on pages
and , or the diagram on the
fuse box lid, which fuse or fuses
control that component. Check those
f uses f irst, but check all the f uses
bef ore deciding that a blown f use is
not the cause. Replace any blown
f uses and check the component’s
operation. 3.
1.
2. 4.
310 311
Checking and Replacing Fuses
Fuses
T aking Care of t he Unexpect ed308
F FU
US SEE P
PU
UL LLLEE R
R
B
BL LOOW WN N
F
FU
US SEE

Î
Î
Î
á
á
à
à
Î
Î
Amps.
No. Circuits Protected
Amps.
No.
Circuits Protected
15 A
10 A
7.5 A
7.5 A
7.5 A 15 A
7.5 A
7.5 A
7.5 A
7.5 A 15 A
30 A
7.5 A
1
2
3
4
5
6
7
8
9
10
11
12
13
On Canadian modelsDriver’s Power Window
Heated Seat
Driver’s Power Seat Slide
Front Passenger’s Power
Seat Slide
Front Passenger’s Power
Seat Reclining
Rear Lef t Power Window
Front Passenger’s Power
Window
ACC (Radio)
Navigation System, OnStar,
Daytime Running Lights
Power Door Locks
Clock, Back up
A/C Mg Clutch
Moonroof
Rear Right Power Window
20 A
20 A
20 A
20 A
20 A
20 A
20 A
20 A
20 A
10 A
7.5 A 20 A
7.5 A
7.5 A 30 A
20 A
1
2
3
4
5
6
7
8
9
10
11
12
13
14 15
16
Fuel Pump
SRS
Heater Control, A/C Clutch
Relay, Cooling Fan Relay
R/C Mirror
Daytime Running Lights
ECU (ECM/PCM), Cruise
Control
SRS
ACC Relay, Navigation
Instrument Panel, Back-up
Lights, Memory Seat
Turn Signals
IG Coil
Wiper, Washer
Starter Signal
Type S only
1:
2:
Driver’s Power Seat Reclining
Interior Light, Courtesy Lights
1
2
1
Fuses
T aking Care of t he Unexpect ed311
INTERIOR FUSE BOXES
Driver’s Side
Passenger’s Side
F Fr roo n
nt
t F
Frroo n
nt
t