ECO mode Acura TL 2004 User Guide

µ
´ ´
µ
Turn the f og lights on and of f by
turning the switch next to the
headlight switch.
Adjust the brightness of the
instrument panel by pressing the
or side of the adjustment button.
Press to increase the brightness
and to decrease it. You can adjust
the brightness with the headlight
switch on or of f .The level of brightness is shown on
the multi-information display while
you adjust it. It goes out 5 seconds
af ter you f inish adjusting.
To reduce glare at night, the
instrument panel illumination dims
when you turn the light switch to
or . Pressing the MAX
button will bring it to the maximum
level.
You can use the f og lights only when
the headlights are on low beam.
Fog L ights, Instrument Panel Brightness
Inst rument s and Cont rols
Fog Lights
(U.S. models only)
Instrument Panel Brightness
75
MAX BUTTON
ADJUSTMENT BUTTON

µµµ
µ
Press this button once to
lock all doors. Some exterior lights
will f lash. When you push LOCK
twice within 5 seconds, you will hear
a beep to verify that the doors are
locked and the security system has
set. You cannot lock the doors if any
door is not f ully closed or if the key
is in the ignition switch. Press this button once
to unlock the driver’s door or all the
doors (depending on the Keyless
Memory Setting). Press it twice to
unlock the other doors. Some
exterior lights will f lash twice each
time you press the button.
The ceiling light (if the ceiling light
switch is in the center position) will
come on when you press the
UNLOCK button. If you do not open
anydoorswithin30seconds(or
whatever setting the relock timer is
set to), the light f ades out. If you
relock the doors with the remote
transmitter before 30 seconds have
elapsed, the light will go of f
immediately. Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk with the
remote transmitter if the trunk main
button is turned of f .
Pressthisbuttonfor
about 2 seconds to attract attention:
thehornwillsoundandtheexterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter or turn the ignition
switch to ON (II).
If you unlock the doors with the
remote transmitter, but do not open
anydoorswithin30seconds,the
doors automatically relock and the
security system sets. To change this
setting, ref er to Keyless Memory
Settings on page . 66
Remote Transmitter
Inst rument s and Cont rols
LOCK UNL OCK
T RUNK
PA NIC
85
TRUNK
RELEASE
BUTTON
LOCK
BUTTON
UNLOCK
BUTTON PANIC
BUTTON
LED

Û
When you press a f an control button,
the fan is taken out of AUTO mode
and starts to run at its lowest speed.
Press the button to make
the f an run f aster.
You can manually select various
f unctions of the climate control
system when it is in f ully automatic
mode. All other f eature remain
automatically controlled. Making any
manual selection causes the word
AUTO in the display to go out.
Press the OFF button. However, a
lack of air f low can cause the
windows to fog up. It is
recommended that you keep the f an
on at all times so stale air and
moisture do not build up in the
interior and cause fogging.
When the AUTO button on the
driver’s side is pressed, the
temperature control buttons on the
passenger’s side are disabled, and
the interior temperature is regulated
to the temperature set on the driver’s
side.WhentheAUTObuttononthe
passenger’s side is pressed,
temperature can be set on the driver’s
side and passenger’s side separately.
The system automatically selects the
proper mix of conditioned and/or
heated air that will, as quickly as
possible, raise or lower the interior
temperature to your pref erence.
When you set the temperature to its
lower or its upper limit, the system
runs at f ull cooling or heating only. It
does not regulate the interior
temperature.
The automatic climate control
system adjusts the f an speed and
airflow levels to maintain the interior
temperature you select.
In the AUTO mode, the vehicle’s
interior temperature is
independently regulated f or the
driver and passenger. If the driver’s
side of the vehicle is getting too
much sun, the system will adjust to a
lower temperature.
Press the AUTO button.
Set the desired temperature with
the temperature control buttons.
You will see AUTO in the system’s
display.
1.
2.
On models with Navigation System
Comf ort and Convenience Feat ures
Climat e Cont rol
T o Cool or Heat A utomatically
Semi-automatic Operation
To Turn Everything Of f
Using A utomatic Climate Control
115

µ
µ ´µ µ
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
VOL/PWR knob or the AM/FM
button (AM or FM button on
Canadian model). Adjust the volume
by turning the same knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button (AM or FM button on
Canadian model). On the FM band,
ST will be displayed if the station is
broadcasting in stereo. Stereo
reproduction on AM is not available. You can use any of f ive methods to
f ind radio stations on the selected
band:
the
preset buttons, and .
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency.
The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or SEEK button, then
release it. If you do nothing, the system will
scan f or the next strong station and
play it f or 5 seconds. When it plays a
station you want to listen to, press
the SCAN button again.The SCAN function
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button, or
touch the SCAN icon (models with
navigation system), then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 5 seconds.
To Play the Radio
To Select a Station
TUNE,SEEK,SCAN, AUTO SELECT
TUNE
SEEK SCAN
Playing the Radio
Comf ort and Convenience Feat ures118

µµEach preset button or
preset icon (models with navigation
system) can store one f requency on
AM and two f requencies on FM.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
stations on FM. If you are
traveling far from home and can no
longer receive your preset stations,
you can use the Auto Select f eature
to find stations in the local area.
Press the A. SEL button or the
AUTO SELECT icon (models with
navigation system). ‘‘A.SEL’’ (AUTO
SEL) f lashes in the display, and the
system goes into scan mode f or
several seconds. It stores the
f requencies of six AM, and twelve
FM stations in the preset buttons.
You will see a ‘‘0’’ displayed or see no
station number on the preset icons
af ter pressing a preset button (icon)
if Auto Select cannot f ind a strong
station f or every preset button. If you do not like the stations Auto
Select has stored, you can store
other f requencies on the preset
buttons (icons). Use the TUNE,
SEEK, or SCAN f unctions to f ind
stations, then store them in the
preset buttons (icons) as previously
described.
press the
A.SEL button (AUTO SELECT icon).
This restores the presets you
originally set.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button (icon).
Pick a preset button (icon), and
hold it until you hear a beep.
1.
2.
3.
4.
To turn of f Auto Select,
CONT INUED
Playing the Radio
Comf ort and Convenience Feat ures
Preset A UT O SEL ECT
119

µµ µ
On models without Navigation System
Bass, Treble, Balance, and Fader are
each adjustable. In addition, you can
adjust the strength of the sound
coming from the center and the
subwoof er speakers.
Press the TUNE/SOUND knob
repeatedly to display the Bass
(BASS), Treble (TREB), Balance
(BAL), Fader (FADE), Center
(CNTR) and Subwoof er (SUBW)
setting.
Eachmodeisshowninthedisplayas
it changes. Turn the TUNE/SOUND
knob to adjust the setting to your
liking. When the level reaches the
center, you will see ‘‘C’’ in the display.
The system will automatically return
the display to the selected audio
mode about 5 seconds af ter you stop
adjusting a mode.
Use the TREB/
BASS modes to adjust the tone to
your liking.
These two
modes adjust the strength of the
sound coming f rom each speaker.
BAL adjust the side-to-side strength,
and FADE adjusts the f ront-to-back
strength. These two
modes adjust the strength of the
sound coming f rom the center
speaker and the subwoof er speaker.
If you turn the TUNE/SOUND knob
all the way to the lef t, you will see
‘‘OFF’’inthedisplay,andthecenter
speaker and/or subwoof er speaker
will be of f .
Playing the Radio
Comf ort and Convenience Feat ures
Adjusting the Sound
Treble/Bass
Balance/FaderCenter/Subwoof er
120
ADJUSTMENT LEVEL

µ
µ
µ
On models with Navigation System
Bass, Treble, Lef t/Right Balance,
and Front/Rear Fader are each
adjustable. In addition, you can
adjust the strength of the sound
coming from the center and the
subwoof er speakers.
To adjust them, enter the sound grid
by touching the SOUND icon on the
display or pressing the TUNE/
SOUND knob.
To adjust the
sound f rom the subwoof er or center
speaker, touch or icon on
each side of the Subwoof er or
Center adjustment bar. Then
continue pressing or , or turn the TUNE/SOUND knob. The
adjustment bar shows you the
current setting.
To adjust the treble
and bass, touch or on each
side of the Treble or Bass
adjustment bar. Then continue
pressing or , or turn the
TUNE/SOUND knob. The
adjustment bar shows you the
current setting. These modes adjust
the strength of the sound coming
f rom each speaker. Lef t/Right
balance adjust the side-to-side
strength, while Front/Rear f ader
adjust the f ront-to-back strength. To
adjust the left/right balance, touch
the lef t or right icon on the sound grid. When you touch an icon, the
yellow bars on the grid turn orange
and move toward the icon, changing
the balance left or right. At this point,
you can also use the TUNE/SOUND
knob to adjust the balance. To
equalize the balance, touch the lef t
or right icon until each side has an
orange bar at the center of the sound
grid.
To adjust the Front/Rear f ader,
touchthefrontorrearicononthe
sound grid. When you touch an icon,
the yellow bars on the grid turn
orange and move toward the icon,
changing the f ader to the f ront or
rear. At this point, you can also use
the TUNE/SOUND knob to adjust
the balance. To equalize the f ader,
touch the f ront or rear icon until
each side has an orange bar at the
center of the sound grid.
To see the audio screen when you
are f inished adjusting the sound,
touch the RETURN icon, or wait 5
seconds.
Playing the Radio
Comf ort and Convenience Feat ures
Subwoof er/Center Treble/Bass
L ef t/Right Balance, and Front/
Rear Fader
121
FADER ADJUST ICON
CENTER ADJUST ICON SUBWOOFER
ADJUST ICONBALANCE
ADJUST
ICON
TREBLE
ADJUST
ICON
BASS ADJUST
ICON

µµ
The SCAN f unction gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the stations within that
category are scanned. To activate
SCAN, press the SCAN button or
touch the SCAN icon on the audio
display (models with navigation
system). The system plays each
channel in numerical order f or a f ew
seconds, then selects the next
channel. When you hear a channel
you want to continue listening to,
press the button or touch the icon
again. To store a channel:
Youcanstoreupto12
preset channel using the six preset
buttons or preset icons (models with
navigation system). Each button
stores one channel f rom the XM1
band and one channel f rom the XM2
band.
To store a channel: Press the button. Either
XM1 or XM2 will show in the
display.
Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel.
In the category mode, only channels
within that category can be selected.
In the channel mode, all channels
can be selected. Pick the preset button (icon) you
want f or that channel. Press and
hold the button (icon) until you
hear a beep.
Repeat steps 2 and 3 to store the
f irst six channels.
Press the button again.
The other XM band will show.
Store the next six channels using
steps 2 and 3.
Once a channel is stored, simply
press and release the proper preset
button (icon) to tune to it.
The presets will be lost if your
vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed.
1.
2. 3.
4.
5.
Playing t he XMSatellite Radio (U.S. Models)
Comf ort and Convenience Feat ures
SCAN
Preset
126

µ´µ´
µ
Select the disc changer by pressing
the DISC/TAPE button (U.S.
models) or CD/DVD button
(Canadian models). The system will
begin playing the last selected disc in
the disc changer. You will see the
disc and track numbers displayed.
To select a dif f erent disc when all six
positions are loaded, use the preset 5
(DISC ) or preset 6 (DISC )
button. Otherwise, press the
corresponding number on the preset
buttons or icons. On models with
navigation system, you can also
touch the appropriate disc icon (1
6) to select a dif f erent disc. Each time you press and release the
SEEK button, the player skips
f orward to the beginning of the next
track. Press and release the SEEK
buttontoskipbackwardtothe
beginning of the current track.
When you press the SCAN button or
touchtheTRACKSCANicononthe
audio display (models with
navigation system), the f irst track of
the current disc plays f or about 10
seconds. You will see SCAN
(TRACK SCAN) highlighted in the
display. To hear the rest of the track,
press the SCAN button or touch
TRACK SCAN again within 10
seconds. If you don’t, the system
advances to the next track, plays
about 10 seconds of it, and continues
through the rest of the tracks the
same way.WhenyoupressandholdtheSCAN
button until you see D-Scan in the
display, or when you touch the DISC
SCAN icon on the audio display
(models with navigation system), the
f irst track of the current disc plays
f or about 10 seconds. You will see D-
Scan (DISC SCAN) in the display. To
hear the rest of the disc, press the
SCAN button or touch DISC SCAN
again, within 10 seconds. If you don’t,
the system advances to the next disc,
plays about 10 seconds of it, and
continues throughout the rest of the
discs the same way. When the
system reaches the last disc, DISC
SCAN is cancelled, and the disc you
originally had on plays normally.
CONT INUED
Playing Discs
Comf ort and Convenience Feat ures
To Play a Disc
To Change Tracks
Track Scan Disc Scan
131

To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJECT’’ in the display.
When you remove the disc f rom the
slot, the system automatically begins
the load sequence so you can load
another disc in that position. If you
do not load another disc, within 15
seconds, the system selects the
previous mode [AM, FM1, FM2,
tape, or Satellite Radio (U.S.
models)].
If you do not remove the disc f rom
the slot, the system will reload the
disc af ter 15 seconds and put the
disc changer in pause mode. To
begin playing the disc, press the disc
button.To remove a dif f erent disc f rom the
changer,firstselectitbypressing
the corresponding number on the
preset button (touching the
appropriate disc icon on models with
navigation system). When that disc
begins playing, press the eject button.
When you press the eject button
while listening to the radio, or with
the audio system turned of f , the disc
that was last selected is ejected.
Af ter that disc is ejected, pressing
the eject button again will eject the
next disc in numerical order. By
doing this six times, you can remove
all the discs f rom the changer.
You can also eject discs when the
ignition switch is of f :
To eject one disc, press and release
the eject button.
To eject all discs, press and hold the
eject button until the system beeps.
Playing Discs
Removing Discs f rom the
Changer
Comf ort and Convenience Feat ures133