ignition Acura TSX 2006 Workshop Manual

If you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
rpm below the red zone.
Bef ore downshif ting, make sure the
engine will not go into the
tachometer’s red zone.The 6-speed manual transmission
has an electric lockout so you cannot
accidentally shif t f rom f if th to
reverse instead of sixth while the
vehicle is moving. If you cannot shif t
to reverse when the vehicle is
stopped:
Apply the parking brake, and turn
the ignition key to the
ACCESSORY (I) or the LOCK (0)
position.
Press the clutch pedal, and shif t to
reverse.
With the clutch pedal still pressed,
start the engine.
If you need to use this procedure to
shif t to reverse, your vehicle may be
developing a problem. Have the
vehicle checked by your dealer. 1.
2.
3.
Manual T ransmission
Engine Speed L imiter Reverse L ockout
Driving
243
——y
y
(yy

The ‘‘D’’ indicator comes on f or a
f ew seconds when you turn the
ignition switch to the ON (II)
position. If it f lashes while driving (in
any shif t position), it indicates a
possible problem in the transmission.If the malf unction indicator lamp
comes on along with the ‘‘D’’
indicator, there is a problem in the
automatic transmission control
system. Avoid rapid acceleration, and
have the transmission checked by
your dealer as soon as possible.
These indicators in the tachometer
show which position the shif t lever is
in. When the ‘‘D’’ indicator warns of a
possible problem with the
transmission, you will see a ‘‘CHECK
TRANSMISSION’’ message in the
multi-inf ormation display (see page
). To shif t f rom any position, move the
shiftlever.Youcannotshiftoutof
Park when the ignition switch is in
the LOCK (0) or the ACCESSORY
(I) position.
82
Automatic Transmission
Shif t L ever Position Indicators
Shif ting
244
SHIFT LEVER
——yy
(yy

µµ
µ
µ
CONT INUED
Use this position f or
your normal driving. The
transmission automatically selects a
suitable gear for the vehicle speed
and acceleration. You may notice the
transmission shif ting up at higher
speeds when the engine is cold. This
helps the engine warm up f aster. Use neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to the Park
position if you need to leave your
vehicle and apply the parking brake.
Press on the brake pedal when you
are moving the shif t lever f rom
neutral to another gear.
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. The shif t lever must be in
Park bef ore you can remove the key
from the ignition switch.
Press the brake
pedal, and move the shif t lever f rom
Park to reverse. To shif t f rom
reverse to neutral, come to a
completestop,andthenshift.
This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal.
If you have done all of the above and
still cannot move the lever out of
Park, see on
page . 249
To shift from:
PtoR
RtoP
NtoR
DtoD DtoN
DtoD NtoDRtoN Do this:
Press the brake pedal
and move the lever.
Move the lever.
3
3
Automatic Transmission
Drive (D) Neutral (N)
Reverse (R)
Park (P)
Shif t L ock ReleaseDriving
245
——y
y
(yy

CONT INUED
This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal and pressing the release
button does not work.Set the parking brake.
Remove the key from the ignition
switch.
If you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
rpm below the red zone.
Putaclothonthenotchof the
shif t lock release slot cover. Using
a small f lat-tipped screwdriver or a
metal f ingernail f ile, caref ully pry
on the notch of the cover to
remove it.
1.
2.
3.
Automatic Transmission
Shif t L ock Release
Engine Speed L imiter
Driving
249
COVER
——yy
(yy

Insert the key in the shift lock
release slot.
Push down on the key while you
move the shift lever out of Park to
neutral.Remove the key from the Shift
Lock Release slot, then reinstall
thecover.Makesurethenotchon
the cover is on the lef t side.
Return the key to the ignition
switch, depress the brake pedal
and restart the engine.
If you need to use the shif t lock
release, it means your vehicle is
developing a problem. Have the
vehicle checked by your dealer. 6.
5. 4.
Automatic Transmission
250
SHIFT LOCK RELEASE SLOT
——yy
(yy

The vehicle stability assist (VSA)
system helps to stabilize the vehicle
during cornering if the vehicle turns
more or less than desired. It also
assists you in maintaining traction
while accelerating on loose or
slippery road surf aces. It does this
by regulating the engine’s output,
and by selectively applying the
brakes.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety. When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times.When VSA activates, you will see the
VSA activation indicator blink.
If this indicator comes on while
driving, pull to the side of the road
when it is saf e, and turn of f the
engine. Reset the system by
restarting the engine. If the VSA
system indicator stays on, or comes
back on while driving, have the VSA
system inspected by your dealer.If the indicator does not come on
when the ignition switch is turned to
the ON (II) position, there may be a
problem with the VSA system. Have
your dealer inspect your vehicle as
soon as possible.
When the VSA system indicator
comes on, you will also see a
‘‘CHECK VSA SYSTEM’’ message in
the multi-information display.
Without VSA, your vehicle will have
normal braking and cornering ability,
but it will not have VSA traction and
stability enhancement.
CONT INUED
Vehicle Stability Assist (VSA) System
VSA A ctivation Indicator
VSA System Indicator
Driving
255
——yy
(yy

µ
µ
µ
µ
µ
µ
µ
µ
µ
µµ
µ
One of the most convenient and
important f eatures of the multi-
inf ormation display on your vehicle
is the maintenance minder.
Based on engine operating
conditions and accumulated engine
revolutions, the onboard computer in
your vehicle calculates the remaining
engine oil lif e.
The system also displays the code
f or other scheduled maintenance
items needing service.
To see the current engine oil lif e
displayed on the lower segment of
the multi-information display, turn
the ignition switch to the ON (II)
position, and press the SEL/RESET
buttononthesteeringwheel
repeatedly until engine oil lif e is
displayed.The remaining engine oil lif e is
displayed on the engine oil lif e
display according to this table:
Calculated Engine Oil Lif e (%)
100% 91% 90% 81%
80% 71%
70% 61%
60% 51%
50% 41%
40% 31%
30% 21%
20% 16%
15% 11%10% 6% 5% 1% 0% Displayed
Engine Oil Lif e (%)
100% 90%
80%
70%
60%
50%
40%
30%
20%
15%
10% 5%
0%
Maintenance Minder
Engine Oil L if e Display
266
REMAINING ENGINE OIL LIFE
ENGINE OIL LIFE DISPLAY
——y
y
(yy

To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.
The message appears in the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position. Af ter canceling the
message, the engine oil lif e display
will appear in the lower segment.
This continues until you have the
indicated maintenance done by your
dealer.When the remaining oil lif e is 5 to 1%,
the multi-information display shows
a ‘‘SERVICE DUE NOW’’ message.
The display also shows the same
maintenance items that were
previously shown with ‘‘SERVICE
DUE SOON.’’ Make sure you have
the indicated maintenance
perf ormed as soon as possible.To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than5seconds,
and then press the INFO button. After have the service is performed,
make sure to reset the display as
described on page .
269
Maintenance Minder
268
——yy
(y
y

CONT INUED
If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows:Turn the ignition switch to the ON
(II) position.
To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display. Press and hold the SEL/RESET
button on the steering wheel f or
more than 10 seconds. The
remaining engine oil lif e reset
modewillbeshownonthemulti-
inf ormation display.
To reset the engine oil lif e, press
the INFO button on the steering
wheel to select ‘‘RESET’’ on the
display, and press the SEL/
RESET button.
After the message in the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
percentage of the remaining engine
oil lif e and the maintenance item
code(s) displayed. Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100 %’’ in the lower
segment of the multi-inf ormation
display and the maintenance item
code(s) erased the next time you
turn the ignition switch to the ON
(II) position.
If the engine oil lif e display is not
displayed, press the SEL/RESET
buttononthesteeringwheel
repeatedly until it comes back.
1.
2.
3.
Maintenance Minder
Maint enance
269
‘‘SERVICE’’ MESSAGE
——yy
(yy

CONT INUED
Park the vehicle on f irm, level and
non-slippery ground. Put the
transmission in Park (automatic)
or reverse (manual). Apply the
parking brake.
If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area that is
far away from the traffic lanes.
Turn on the hazard warning lights,
and turn the ignition switch to the
LOCK (0) position. Have all
passengers get out of the vehicle
while you change the tire.
2.
1.
Changing a Flat Tire
T aking Care of t he Unexpect ed
313
TRUNK FLOOR
JACK TOOL TRAY TOOLS
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.
——yy
(y
y