ignition Acura TSX 2008 User Guide

This shows how much f uel you
have. It may show slightly more
or less than the actual amount.
The needle returns to the
bottom after you turn off the
ignition.
This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise to
about the middle of the gauge. In
severe driving conditions, such as
very hot weather or a long period of
uphill driving, the pointer may rise to
the upper zone. If it reaches the red (Hot) mark, pull saf ely to the side of
the road. See page f or
instructions and precautions on
checking the engine’s cooling
system.
333
Gauges
Temperature Gauge Fuel Gauge
68
TACHOMETER
SPEEDOMETER
TEMPERATURE
GAUGE
INFO KNOB SELECT/RESET KNOBFUEL GAUGE
U.S. model is shown.
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.
\f—\f—
y

y
(\fy\f\fy
2008 TSX

The multi-inf ormation display in the
instrument panel displays various
inf ormation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comf ortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs f or continued trouble-f ree
driving.When you turn the ignition switch to
the ACCESSORY (I) position, the
display shows ‘‘Goodbye.’’
There are three types of messages;
normal display messages, engine oil
lif e and maintenance messages, and
system messages.
You can also customize some vehicle
control settings to your liking with
the multi-inf ormation display and the
two buttons on the steering wheel
(see page ).
When you unlock and open the
driver’s door with the remote
transmitter, the display shows
‘‘Welcome Driver 1’’ or ‘‘Welcome
Driver 2’’ depending on which
remote transmitter you use. The
driver’s ‘‘ID’’ is detected by the
transmitter. For more information
about driver’s ‘‘ID’’, see page .If you use the key to unlock the
driver’s door, the display only shows
‘‘Welcome.’’ This means the system
cannot recognize either ‘‘Driver 1’’ or
‘‘Driver 2.’’ In this case, you cannot
use the customized settings on the
multi-inf ormation display (see page
).
86
13286
CONT INUED
Normal Display Messages
Multi-Inf ormation Display
Inst rument s and Cont rols
69
\f—\f—
y
y
(\fy\f\fy
2008 TSX

RANGE: The estimated distance
you can travel on the fuel
remaining in the tank. This
distance is estimated from the fuel
economy you received over the
last several miles, so it will vary
with changes in speed, traf f ic, etc.
ELAPSED TIME: The time
traveled since you last reset the
trip computer.
AVG. SPEED: The average speed
you are traveling.
TIRE PRESSURE MONITOR:
You can see the pressure of each
tire in this monitor. If the tire
pressure is low on one or more
tires, inf late them to the correct
pressure. For more inf ormation,
see page .
The primary display always shows its
def ault setting, ‘‘INST. MPG’’ (U.S.
models) or ‘‘INST. L/100 km’’
(Canadian models) even if you press
the INFO button. It only changes the
secondary display. You can
customize this setting to your liking
(see page ).
The upper segment is divided into
two displays; primary and secondary.
After you turn the ignition switch to
the ON (II) position, press the INFO
button on the steering wheel or the
INFO knob in the instrument panel.
What you last selected appears on
the secondary display of the trip
computer. Pressing the INFO
button/knob repeatedly changes the
display as shown in the example on
the previous page. Messages in the trip computer
include:
When you turn the ignition switch
to the ON (II) position, ELAPSED
TIME is reset.
INST.MPG(U.S.models)/
INST.L/100 km (Canadian
models): Your vehicle’s current
f uel mileage.
AVG. FUEL A/AVG. FUEL B:
Your vehicle’s average fuel
economy since you last reset the
Trip A or Trip B. When you select
Trip B in the lower segment by
pressing the SEL/RESET button
on the steering wheel or select/
reset knob in the instrument panel,
the AVG. FUEL B appears in the
secondary display. 102
264
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
71
INFO KNOBINFO BUTTON
——
y
y
(yy
2008 TSX

While a trip meter is displayed, you
can change the display between
‘‘Trip A’’ and ‘‘Trip B’’ by pressing
the SEL/RESET button on the
steering wheel, or the select/reset
knob in the instrument panel.
To reset a trip meter, display it, and
press and hold the SEL/RESET
button or select/reset knob until the
number resets to ‘‘0.0.’’ When you
reset ‘‘Trip B’’ , ‘‘AVG. FUEL B’’ is
also reset. If you reset ‘‘Trip A’’,
‘‘AVG. FUEL A’’ and ‘‘AVG. SPEED’’
willberesetatthesametime.
In the lower segment, each time you
press the SEL/RESET button on the
steering wheel, the display changes
f rom ‘‘Trip A/Odometer’’ to ‘‘Trip A/
Outside Temperature’’ to ‘‘Trip B/
Outside Temperature’’ to ‘‘Engine
OilLife,’’andthenbacktothe
‘‘Trip A/Odometer’’ as shown on
page . When you turn the ignition switch to
the ON (II) position, what you last
selected is displayed. You can also change the display by
pushing the select/reset knob in the
instrument panel.
70
Multi-Inf ormation Display
Trip Meter
72
SELECT/RESET
KNOB
SEL/RESET
BUTTON
LOWER SEGMENT
U.S.model is shown
——
y

y
(yy
2008 TSX

When the engine oil lif e reaches 15 %,
the display shows ‘‘SERVICE DUE
SOON’’ and the code f or the
maintenance items to be perf ormed.
When the engine oil lif e reaches 5 %,
the display shows ‘‘SERVICE DUE
NOW’’ along with the same
maintenance items.Have your dealer do the indicated
maintenance as soon as you see this
message, and have them reset the
display af ter completing the service.
If you do not perf orm the indicated
maintenance or do not reset the
display, the message changes to
‘‘SERVICE PAST DUE’’ when the
engine oil lif e becomes 0 %.These messages appear on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position.
For more inf ormation about
Maintenance Messages, see
‘‘
’’ on page
.
Also ref er to page f or important
maintenance saf ety precautions. 280
278
Multi-Inf ormation Display
Maintenance Messages
Maintenance Minder
74
U.S.model is shown
\f—\f—
y
y
(\fy\f\fy
2008 TSX

If you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
the driver’s door, you will see
‘‘REMOVE KEY’’ on the display and
hear a reminder beeper.If the brake f luid level is at or below
theMINmarkonthesideof the
brake f luid reservoir in the engine
compartment, you will see ‘‘BRAKE
FLUID LOW.’’ If you see this
message, have the brake system
checked by your dealer (see page
). If thefuelfillcapismissingornot
tightened properly, you will see
‘‘TIGHTEN FUEL CAP.’’ Make sure
the fuel cap is installed and tightened
at least one click.
300
CONT INUED
Multi-Inf ormation Display
Remove Key Brake Fluid LowTighten Fuel Cap
Inst rument s and Cont rols
79
U.S.Canada
\f—\f—
y
y
(\fy\f\fy
2008 TSX

You can customize some vehicle
control settings f or ‘‘DRIVER 1’’ and
‘‘DRIVER 2’’ separately.
To have the driver’s ID detected,
make sure you use your transmitter
to unlock the driver’s door.
If you use the key to unlock the
driver’s door, the system cannot
recognize either ‘‘DRIVER 1’’ or
‘‘DRIVER 2.’’ In this case, when you
try to enter the customizing mode,‘‘DRIVER UNKNOWN
CUSTOMIZE IMPOSSIBLE’’ will be
displayed, and you cannot customize
some of the settings.
Refertothetableonpagetosee
what settings you can customize.
If you use your remote transmitter to
unlock the driver’s door, and the
system f ails to recognize either
‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ see
page to link your transmitter to
your vehicle.
To use the system, your cell phone
and the HFL system must be linked.
Not all cell phones are compatible
with this system. Ref er to page
for instructions on how to link
your cell phone to the HFL and how
to receive or make phone calls, or
visit the acura.com/handsfreelink
website.
With the ignition switch in the ON
(II) position, press and hold the
INFO button for more than 3
seconds. ‘‘CUSTOMIZE ENTRY’’
appears on the multi-inf ormation
display. 219
88
132
Multi-Inf ormation Display
Customized Settings
86
DRIVER’S
ID
\f—\f—
y
y
(\fy\f\f
y
2008 TSX

While the multi-information display
shows ‘‘METER SETUP,’’ press the
SEL/RESET button on the steering
wheel. Press the INFO button until
you see ‘‘PRIMARY DISP
SELECTION’’ as shown above.
When you turn the ignition switch to
the ON (II) position, the primary
display of the trip computer always
shows ‘‘INST. MPG’’ (U.S. models)
or ‘‘INST. L/100 km’’ (Canadian
models) in def ault setting. You can
customize this setting to your liking
in f ollowing procedure.
Press the SEL/RESET button. The
display changes as shown above.
The lower segment changes f rom
‘‘INST. FUEL,’’ to ‘‘AVG. FUEL,’’ to
‘‘RANGE,’’ to ‘‘ELAPSED TIME,’’
then to ‘‘AVG. SPEED’’ each time
you press the INFO button. Enter
your selection by pressing the SEL/
RESET button.
Primary Display Select ion
Multi-Inf ormation Display
102
\f—\f—
y
\f\f
\fy
(\fy\f
\fy
2008 TSX

The headlights, parking lights,
taillights, and license plate lights
turn of f af ter the selected time when
you remove the key f rom the ignition
switch and close the driver’s door.If you f ail to enter your selection,
you will see the above display f or
several seconds, then the display
goes back to ‘‘CUSTOMIZE MENU.’’
Repeat the setup.To exit ‘‘HEADLIGHT AUTO OFF
TIMER,’’ press the INFO button
until you see ‘‘EXIT,’’ then press the
SEL/RESET button. The display
goes back to ‘‘CUSTOMIZE MENU.’’
Multi-Inf ormation Display
Inst rument s and Cont rols
109
\f—\f—
y
\f
\fy
(\fy\f

y
2008 TSX

µµPush down on the
lef t lever to signal a lef t turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever in
the proper direction and hold it. The
lever will return to center when you
release it or complete a turn. Turning the switch
on the lef t lever to the
‘‘ ’’position turns on the parking
lights, taillights, instrument panel
lights, side-marker lights, and rear
license plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights.
When the light switch is in the
‘‘ ’’ or the ‘‘ ’’ position, the
Lights On indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or LOCK (0)
position.
If you leave the lights on with the
key removed f rom the ignition
switch, you will hear a reminder
chime when you open the driver’s
door.
Turn signal
Of f
Parking and indicator lights
Headlights
High beams
Flashhighbeams
Fog lights of f
Fog lights on
1.
2.
3.
4.
5.
6.
7.
8.
CONT INUED
Turn Signal
Headlights
Turn Signals and Headlights
Inst rument s and Cont rols
121
\f—\f—
y
\fy
(\fy\f
y
2008 TSX