reset Acura TSX 2009 Owner's Guide

Û
Ý ÛÝ
CONT INUED
Interior Light Dimming Time
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘INTERIOR LIGHT DIMMING
TIME’’ and repeat the procedure
again.
The interior lights f ade out when you
close all doors. To change how long
thelightsstayonbeforetheyfade
out, f ollow these instructions:
You can choose this item to
customize f rom ‘‘LIGHTING
SETUP’’ by pressing the INFO ( /
) button repeatedly. Select the desired setting (15 SEC,
30 SEC, or 60 SEC) by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
Multi-Inf ormation Display
Inst rument s and Cont rols
95
\f—\f—\fy\f\f
y
)!
\f\fy\f
\f\fy
2009 TSX

Û
Ý
ÛÝ
Headlight Auto Of f Timer
You can choose this item to
customize f rom ‘‘LIGHTING
SETUP’’ by pressing the INFO ( /) button repeatedly. Press the SEL/RESET button to see
the selections.
The headlights, parking lights, side
marker lights, taillights, and license
plate lights go of f af ter the selected
time when you remove the key f rom
the ignition switch and close the
driver’s door. To change how long
thelightsstayonbeforetheygooff,
f ollow these instructions:
Select the desired setting (60 SEC,
30 SEC, 15 SEC or 0 SEC) by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
96
\f—\f—\fy\f\fy
)!
\f\fy\f
\f
y
2009 TSX

ÛÝWhen your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
LIGHT SENSITIVITY’’ and repeat
the procedure again.
Press the SEL/RESET button to see
the selections.
Select the desired setting (MAX,
HIGH, MID, LOW or MIN) by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
98
\f—\f—\fy\f\fy
)!
\f\fy\f
\fy
2009 TSX

Û
Ý
ÛÝ
ÛÝ
CONT INUED
AUTO DOOR LOCK
Here are the five custom settings for
the door setup:
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK TIMER
AUTO DOOR UNLOCK
While ‘‘DOOR SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
Multi-Inf ormation Display
Door Setup
Inst rument s and Cont rols
99
: Press the INFO button ( / ).
: Press the SEL/
RESET button.
\f—\f—\fy\f\fy
)!
\f\fy\f
\fy
2009 TSX

µÛÝ
µ µ
ÛÝ
Auto Door Lock
(Automatic transmission model only)
There are three settings you can
choose f rom:
SHIFT FROM P
The doors lock whenever you move
the shift lever out of Park.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
OFF
The auto door lock is deactivated all
the time.
WITH VEH SPD
The doors lock when the vehicle
speed reaches about 10 mph (about
15 km/h).
You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.Press the SEL/RESET button to
enter the selecting mode.
Multi-Inf ormation Display
100
A/T model is shown.
\f—\f—\fy\f
\fy
)!
\f\fy\f
\fy
2009 TSX

ÛÝ
Press the SEL/RESET button to
enter the selecting mode.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘KEY
AND REMOTE UNLOCK MODE’’
and repeat the procedure again.
Multi-Inf ormation Display
102
\f—\f—\fy\f

y
)!
\f\fy\f
\fy
2009 TSX

ÛÝ
ÛÝ
Keyless Lock Acknowledgment
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When you push the LOCK button on
the remote transmitter, some
exterior lights f lash, and a beeper
sounds when you push the LOCK
button again within 5 seconds to
verify that the doors and the trunk
arelockedandthesecuritysystem
has set (see page ). You can
customize the exterior lights not to
f lash and the beeper not to sound.
You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.Press the SEL/RESET button to
enter the selecting mode.
293
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
103
\f—\f—\fy\f
y
)!
\f\fy\f
\fy
2009 TSX

ÛÝWhen your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Press the SEL/RESET button to
enter the selecting mode. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘SECURITY RELOCK TIMER’’ and
repeat the procedure again.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
105
\f—\f—\fy\f
y
)!
\f\fy\f

\fy
2009 TSX

ÛÝ ÛÝWhen your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
DOOR UNLOCK’’ and repeat the
procedure again.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Press the SEL/RESET button to
enter the selecting mode.
If you choose ‘‘DRIVER DOOR with
SHIFT to P,’’ you will see the above
display. If you choose ‘‘ALL DOORS WITH
IGN OFF,’’ you will see the above
display.
Press the INFO ( / ) button to
switch the door lock mode setting.
Then, press the SEL/RESET button
to enter your selection.
Multi-Inf ormation Display
Inst rument s and Cont rols
107
A/T model is shown.
A/T model is shown.
\f—\f—\fy\f\fy
)!
\f\fy\f

y
2009 TSX

ÛÝ ÛÝ
If you want to set the def ault settings,
press the INFO ( / ) button to
select DEFAULT ALL, then press
the SEL/RESET button.
If the setting is not successfully
completed, ‘‘FAILED’’ is shown f or
several seconds, and then the screen
goes back to the normal message
mode. Repeat the same procedure to
select DEFAULT ALL.
If you want to cancel DEFAULT
ALL, select CANCEL, then press the
SEL/RESET button. The screen
goes back to the previous display.
To set the def ault settings, press the
INFO ( / ) button to select SET
then press the SEL/RESET button.
When DEFAULT ALL is set, you will
see the above display for several
seconds, then the screen returns to
the default all setting display.
DEFAUL T AL L
Multi-Inf ormation Display
108
\f—\f—\fy\f

y
)!
\f\fy\f

y
2009 TSX