ignition Acura TSX 2009 Owner's Guide

Always use the f ully-extended key
when you insert it to the ignition
switch. If the key does not f ully
extend, the immobilizer system may
not operate properly and may
prevent the engine f rom starting.
The master key can be retracted into
theremotetransmitter.Tousethe
key, push the release button to
release the key f rom the transmitter.
The key should be f ully extended.
To retract the key, push the release
buttonandatthesametimepushthe
key into the remote transmitter until
it is securely latched. Thekeymaycomeincontactwith
your f inger while being retracted or
extended. Make sure your f ingers do
not touch the pivot of the key when
retracting or extending the key.Retractable Master Key
Keys and Locks
120
Push
RELEASE BUTTON
\f—\f—\fy\fy
)!
\f\fy\f
y
2009 TSX

If the system repeatedly does not
recognize the coding of your key,
contact your dealer.
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle undrivable.
If you lose your key and you cannot
start the engine, contact your dealer.
The immobilizer system protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine’s f uel
system is disabled.
When you turn the ignition switch to
the ON (II) position, the immobilizer
system indicator should come on
brief ly, then go of f . If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to the
LOCK (0) position, remove the key,
reinsert it, and turn the ignition
switch to the ON (II) position again.
The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
chain) is near the ignition switch
when you insert the key.As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Immobilizer System
Inst rument s and Cont rols
121
Always take the ignition key with you
whenever you leave the vehicle alone.
\f—\f—\fy\f\fy
)!
\f\fy\f
y
2009 TSX

µ
µ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III). If you turn the ignition key to the
ACCESSORY (I) position with the
driver’s door closed, you will see a
‘‘ACCESSORY (I) POSITION’’
message on the multi-inf ormation
display to inf orm you of the key
position.
This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom the
ACCESSORY (I) to the ON (II)
position.
If the f ront wheels are turned, the
anti-thef t lock may make it dif f icult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key. You can insert or
remove the key only in this position.
To turn the key, push it in slightly. If
your vehicle has an automatic
transmission, the shif t lever must
also be in Park.
You can
operate the audio system and the
accessory power sockets in this
position.
If you leave the key in the ignition
switch in the ACCESSORY (I)
position and open the driver’s door,
you will see a ‘‘RETURN IGNITION
SWITCH TO LOCK (0) POSITION’’
message on the multi-inf ormation
display and hear a reminder beeper.
Ignition Switch
ON (II)
LOCK (0)
A CCESSORY (I)
122
\f—\f—\fy\f
y
)!
\f\fy\f
y
2009 TSX

µUse this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key.
You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or the
ACCESSORY (I) position and open
thedriver’sdoor.Removethekeyto
turn of f the beeper.
You will also see a ‘‘REMOVE KEY’’
message on the multi-inf ormation
display.
If your vehicle has an automatic
transmission, the shif t lever must be
in Park bef ore you can remove the
key f rom the ignition switch.
Ignition Switch
ST A RT (III)
Inst rument s and Cont rols
123
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control of the
vehicle.
Remove the key from the
ignition switch only when
parked.
——yy
)!
y
y
2009 TSX

The childproof door locks are
designed to prevent children seated
in the rear f rom accidentally opening
the rear doors. Each rear door has a
lock lever near the edge. With the
lever in the LOCK position (lever is
down), the door cannot be opened
f rom the inside regardless of the
position of the lock tab. To open the
door, push the lock tab f orward and
use the outside door handle.
If you f orget and leave the key in the
ignition switch, lockout prevention
will not allow you to lock the driver’s
door. With any door open and the
key in the ignition switch, locking
with master door lock switch is
disabled. If the driver’s door is
closed, the lock tab on the driver’s
door is not disabled. Pulling the
driver’s lock tab rearward will lock
all doors. If you try to lock an open
driver’s door by pulling the lock tab
rearward, the driver’s door lock tab
pops out and unlocks the driver’s
door.
When you shif t to P af ter driving, the
driver’s door unlocks.
When the vehicle speed reaches
about 10 mph (15 km/h) or more, all
the doors lock automatically.
To lock any passenger’s door when
getting out of the vehicle, pull the
lock tab rearward and close the door.
To lock the driver’s door, remove the
key f rom the ignition switch, pull the
locktabrearwardorpushthefront
of the master switch, then close the
door.
Def ault setting L ockout Prevent ion
Childproof Door L ocks
Door L ocks
Inst rument s and Cont rols
125
Unlock
Lock LEVER
\f—\f—\fy\fy
)!
\f\fy\f
\fy
2009 TSX

µµ
Press this button once to
lock all doors. Some exterior lights
will f lash. When you push LOCK
twice within 5 seconds, you will hear
a beep to verify that the doors are
locked and the security system has
set. You cannot lock the doors if any
door is not f ully closed or if the key
is in the ignition switch. Press this button once
to unlock the driver’s door (or all the
doors depending on the door lock
setting). Push it twice to unlock the
remaining doors. Some exterior
lights will f lash twice the f irst time
when you push the button. On the keyless lock
acknowledgment, you can deactivate
the beep on locking and f lashing of
the lights (see page ).
To change the lock/unlock setting
and the relock timer setting, refer to
the customized settings on page .
Locking and unlocking the driver’s
door will also lock and unlock the
f uel f ill door (see page ).
You can also open all power windows
and the moonroof f rom outside the
vehicle with the remote transmitter
(see page ).
If you do not open any door within 30
seconds, the doors automatically
relock and the security system sets.
The ceiling light and the door
activated spotlights come on when
you press the UNLOCK button if the
lights are in the door activated
position. If you do not open any door
within 30 seconds (or whatever
setting of the interior light dimming
time is set to), the light(s) will f ade
out. If you relock the doors with the
remote transmitter before 30
seconds have elapsed, the light(s)
will go of f immediately. 127
99
357
149
Remote Transmitter
LOCK UNL OCK
126
LED LOCK BUTTON
UNLOCK
BUTTON PANIC
BUTTON
\f—\f—\fy\fy
)!
\f\fy\f

y
2009 TSX

µµ When you unlock the driver’s door
with your remote transmitter, each
remote transmitter activates the
customized settings related to that
remote. Here are the settings activated with
the remote;
Customized settings
(see page ).
Press and hold this
button for about 1 second to attract
attention; the horn will sound, and
the exterior lights will f lash f or about
30 seconds. To cancel panic mode,
press any other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position. Panic
mode does not work when the key is
in the ignition switch.
Press and hold this
button f or about 1 second to open
the trunk. You cannot open the trunk
if the key is in the ignition switch.
The driving position memory
activated (Driver 1, Driver 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in the
memory that is activated by the
transmitter you normally carry. You will also see the ‘‘DRIVER 1’’ or
‘‘DRIVER 2’’ message on the multi-
inf ormation display, depending on
which linked remote transmitter is
used.
When you open the driver’s door
after unlocking it with the remote
transmitter, the driver’s seat moves
to the position stored in memory.
You will hear two beeps when the
movement is completed. The
indicator in the related memory
button on the driver’s door remains
on.Driving position memory
(see page ).
81
142
CONT INUED
U.S. TSX and Canadian TSX Premium
Recalling a Memorized Driving
Position
PA NIC
TRUNK
Remote Transmitter
Inst rument s and Cont rols
127
With Driver 2
With Driver 1
\f—\f—\fy


y
)!
\f\fy\f
y
2009 TSX

µMoves the whole seat
up and f orward, or
down and backward.
Thefrontof theseat
also tilts up or down at
thesametime.
Moves the seat
f orward and backward.
Moves the f ront of the
seat up or down.
Raises or lowers the
seat. Adjusts the seat-back
angle f orward or
backward.
The controls f or the power
adjustable front seats are on the
outside edge of each seat bottom.
You can adjust the seats with the
ignition switch in any position. Make
all seat adjustments bef ore you start
driving.
The passenger seat has the same
adjustments as the driver’s seat but
without any height adjustment.
The driver’s seat includes a memory
f eature. Two seat positions can be
stored in separate memories. You
canthenselectamemorizedposition
by pushing the appropriate memory
button. Ref er to page f or how to
memorize and select the seat
positions.142
Driver’s seat only:
Driver’s seat only:
See pagesf or important saf ety
inf ormation and warnings about how toproperly position the seats and seat-backs. 14
Driver’s seat only:
13
U.S. TSX and Canadian TSX Premium
Seats
Power Seat A djustments
134
Driver’s seat is shown.
\f—\f—\fy

y
)!
\f\fy\f
y
2009 TSX

In the HI setting, the heater turns off
when the seat gets warm, and turns
back on after the seat’s temperature
drops.
In the LO setting, the heater runs
continuously. It does not cycle with
temperature changes.
Follow these precautions whenever
you use the seat heaters:If the engine is lef t idling f or an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting.
Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
Both f ront seats are equipped with
seat heaters. Because of the sensors
f or the side airbag cutof f system,
there is no heater in the passenger’s
seat-back. The ignition switch must
be in the ON (II) position to use the
heaters. Push the front of the switch, HI, to
rapidly heat up the seat. Af ter the
seat reaches a comfortable
temperature, select LO by pushing
the back of the switch. This will keep
the seat warm.
Seat Heaters
Inst rument s and Cont rols
141
Passenger’s
Seat
Driver’s
Seat
HEATERS
SEAT HEATER SWITCH
\f—\f—\fy\f
y
)!
\f\fy\f
y
2009 TSX

Store a driving position only when
the vehicle is parked.Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Adjust the seat to a comfortable
position (see page ). Press and release the SET button
on the control panel. You will hear
a beep. Immediately press and
hold one of the memory buttons (1
or 2) until you hear two beeps.
The indicator in the memory
button will come on. The current
position of the driver’s seat is now
stored.
This setting can be linked or
unlinked with the remote transmitter.
To switch the link setting, see page
.
Two seat positions can be stored in
separate memories. You select a
memorized position by pushing the
appropriate button or using the
appropriate remote transmitter
(Driver 1 or Driver 2).
Your vehicle has a memory feature
f or the driver’s seat position.
3.
1.
2.
134
93
U.S. TSX and Canadian TSX PremiumStoring a Driving Position in
Memory
Driving Position Memory System
142
MEMORY BUTTONS
SET BUTTON
\f—\f—\fy

y
)!
\f\fy\f
y
2009 TSX