turn signal Acura TSX 2013 Navigation Manual

6
Audio SystemYou can play music from a wide array of media sources. Yo
u can also control the audio
system using voice commands.
Basic Operation Audio Buttonsa
Press the VOL
9

(Volume/Power) knob to turn the audio system on/off.
b
Select the audio source.
c
Rotate the VOL
9

(Volume/Power) knob to adjust the volume.
TITLE Displays track title,
artist, and other text
information, if available. 8 Bass, treble, and
balance settings.
1 to 6 Preset stations (FM/AM) and channels (XM). SKIP Finds stations with strong signal (FM/AM). Skip to start/end of tracks, or press and hold to fast reverse/forward (Disc). SCAN Plays 10-second sample of each station (FM/ AM), channel (XM), or track (Disc). Press again to play the current selection. A.SEL Scans and automatically
stores the strongest
FM/AM station in each preset.
TUNE Tunes to next frequency (FM/AM) or channel (XM). Fast-reverse/forward.
CATEGORY Selects next category (XM) or next folder (WMA, MP3, AAC).
Loading a Disca
Press the DISC/HDD button.
b
Insert a disc into the disc slot. The disc automatically starts playing.
c
Press the AUDIO button to display the audio screen. Select an audio source (e.g., FM/AM) to stop the disc. Press the
E
(Eject) button to remove
the disc. If you eject but do not remove the disc, the disc automatically reloads after a few seconds.
QRG
Quick Reference Guide - 2013 TSX

16
Troubleshooting
For more Information
(P209)
Why does the vehicle position icon on the map “lag” a short distance behind my actual position, especially at intersections? This is normal. The navigation system is unaware of the width of intersections. Large differences in vehicle position can indicate a temporary loss of the GPS signal. Why does the “time to dest
ination” display sometimes
increase even though I am getting closer to my destination? The “time to destination” is based on the posted road speed signs and your actual road speed to give you a better estimate of arrival time. Why does my clock frequently change the time forward and backward by one hour? The clock setting is automatically updated based on your GPS location. If you normally drive between two time zones, the clock may keep adjusting the time. You can turn this feature off. 2Clock Adjustment
P. 58
How do I specify a destination when an entered city or street could not be found? Try entering the street first. Some cities are lumped in with a major metro area. In rural
“unverified” areas or new
subdivisions, streets may be
missing or only partially
numbered. How do I turn on the navigation system voice guidance? 1.Press the INFO/PHONE button. Rotate
i
to select
Setup
and press
u
. Check that
Volume
is not set to
OFF
.
2.Move
y
to select
Other
, rotate
i
to select
Basic
Settings
, and press
u
. Set
Voice Recognition Tutor

to ON
if you want the system
to provide confirmations
and system prompts.My battery was disconnected or went dead, and the navigation system is asking for a code. Where do I find it? Your vehicle comes with a card in the glove box that includes the 5-digit security code and serial number. You should keep this card in a safe place outside your vehicle. If you cannot find it, contact your dealer. QRG
Quick Reference Guide - 2013 TSX

138

Playing FM/AM Radio
Radio Data System (RDS)
Audio
Radio Data System (RDS)Provides text data information related to
your selected RDS capable FM station.
Press the TITLE button to turn RDS informati
on on or off. When set to ON, the name
of the FM station is displayed on the displa
y. When set to OFF, the frequency of the
station is displayed. HAUDIO button (in FM/AM mode)
 AUDIO MENU
 RDS Search
Search for FM stations with a strong signal
that are broadcasting the selected RDS
category information.
1.Move
w
or
y
to
select
a search

method (
Seek Up
, Seek
Down
,
Scan
).
2.Rotate
i
to select a category.
Press
u
.

Scanning for stations in that category begins.

If there are no RDS-capable stations in the area, “NOTHING” briefly appears on the display.
■RDS Info Display■Searching for Programs by RDS Category
1RDS Info DisplayRDS information is displayed on the audio screen, if available.
QRG

170Audio
Adjusting the SoundHAUDIO button
 AUDIO MENU
 Sound Setup
Adjust the sound bass, treble, fader, and ba
lance. You can also adjust the strength
of the sound coming from the center and
subwoofer speakers. In
addition, you can
set Dolby PL (ProLogic) II and Speed-s
ensitive Volume Compensation (SVC).
1.Rotate
i
to select the sound
mode to adjust. Press
u
.
2.Rotate
i
to adjust the desired
level. Press
u
.

The display returns to the audio screen after a few seconds.
You can also use the
8
(Sound) button to adjust the sound. Press the
8

button repeatedly to cycle through the edit
modes, displayed on the display. Rotate
the VOL
9
knob to adjust the setting.
1Adjusting the SoundYou can check the level on the navigation screen or on the display. When the level reaches the center, you will see “C” in the display. Fader adjusts the front-t
o-back strength, while
balance adjusts the side-to-side strength. If the fader adjustment is set to the maximum front level, the subwoofer is turned off. If the fader is set to the maximum rear level, the center speaker is off. Dolby PL II signal proc
essing creates multi-
channel surround sound fro
m 2-channel stereo
audio sources. Dolby ProL
ogic II is available only
in DISC (CD-DA, MP3, WMA, AAC), XM® Radio, AUX (USB, iPod®, AUX,
Bluetooth
® Audio), and
HDD modes. Manufactured under license from Dolby Laboratories. Dolby, ProL
ogic, MLP Lossless and
the double-D symbol are trademarks of Dolby Laboratories. The
SVC
has four modes:
OFF
, LOW
, MID
, and
HIGH
. SVC adjusts the volume level based on the
vehicle speed. The faster you go, the audio volume increases. As you slow down, the audio volume decreases. If you feel the sound is too loud, choose
LOW
, and vice versa.
TREBLE
BASS
SVC
BALANCE
FADER
SUBWOOFER
DOLBY PL II
CENTER
QRG

188

Bluetooth
® HandsFreeLink®
Receiving a Call
Bluetooth® HandsFreeLink®
Receiving a Call
1.Press the
h
(Pick-Up) button to
answer a call and display the Calling screen.
“HANDSFREELINK” is also displayed on the display.
2.Press the
j
(Hang-Up) button to
terminate the call.
The following options are available during a call: •Direct Dial
(available on some phones): Allows you to send numbers or names
during a call. This is useful when you call an automated phone system.•Transfer
: Allows you to transfer a call from HFL to your phone, or from your
phone to HFL.•Mute
: Allows you to mute your voice.
1Receiving a CallAn incoming call notif
ication appears on the
screen, and you hear
an audible ring tone.
If your phone has Call
Waiting, press the
h

button to put the original call on hold and answer the incoming call. To return to the original call, press the
h
button again. If you
want to hang up the origin
al call and answer the
new call, press the
j
button.
To change the volume leve
l of HFL, use the audio
system volume knob or the steering wheel volume controls. Some phones may send battery, signal strength, and roaming status information to the screen.
Call ID
Bluetooth
indicator Roaming status
Signal strength Battery level
QRG

212

Troubleshooting
Traffic
Troubleshooting
Traffic
Problem
Solution
AcuraLink Real-Time Traffic™ information could not be received or is not displayed properly.
• Check the traffic icon is displayed and enabled on the icon bar.• Your XM traffic subscription may have expire
d. Check your subscription. Call XM at
(800) 852-9696 and verify your account status
. If your subscription has lapsed, you
may need to request a “rapid refresh.” After XM refreshes your account status, leave the vehicle running outside for
30 minutes to receive the refresh.
2Traffic and Weather Status
P. 64
• There may be a temporary technical problem in your metropolitan area. Call Acura Client Services to see if there is an outage. 2Acura Client Services Contact Information
P. 226
• If the situation persists, see your Acura dealer for assistance.• AcuraLink relies on a satellite signal and is not available in Alaska, Hawaii, Canada, and Puerto Rico.
The navigation system sometimes provides a detour route when I am drivi
ng a route on the freeway.
If Traffic Rerouting
is set to
ON
, the navigation system provides a detour route to
your destination only if it can find a signific
antly faster route than the original one.
2Traffic Rerouting
P. 52
The navigation system routes me to an exit and an alternate freeway with unknown flow speeds or surface streets.
The navigation system predicts which ro
ute should be faster based on freeway
congestion along your route. Use your own experience to determine whether the alternate route would be faster.
How can I ignore the detour route and return to the original route?
Press the INFO/PHONE button. Select
Setup
> Other
> Routing & Guidance
, and set
Traffic Rerouting
to
OFF
.
2Traffic Rerouting
P. 52
QRG

214

Troubleshooting
Guidance, Routing
Troubleshooting
The vehicle position icon on the map “lags” a short distance behind, especially when I arrive at an intersection.
This is normal. The navigation system is unaware of the width of intersections. Large differences in vehicle position can indicate a temporary loss of the GPS signal. 2GPS System
P. 224
The screen is showing white dots as I drive along.
These dots are called “breadcrumbs.” These are displayed if
Off-road Tracking
is set
to ON
and you drive more than 1/2 mile off mapped roads.
2Off-road Tracking
P. 61
How do I remove the white dots (“breadcrumbs”) from my screen?
Press the INFO/PHONE button. Select
Setup
> Other
> Vehicle
, and set
Off-road
Tracking
to
OFF
, then return
to the map.
2Off-road Tracking
P. 61
A road that I selected to avoid is being used when routing.
When you “draw” your area to avoid, make
sure to select sections of roads that
include at least one intersection. 2Avoiding Streets
P. 122
My elevation (shown when I display the current position) seems to fluctuate even though my elevation has not changed.
This is normal. The elevation can vary
±100 feet due to GPS calculation errors.
2GPS System
P. 224
My elevation is missing on the “current position” screen.
The elevation is only displayed if the GPS antenna can receive signals from at least four satellites. Try moving the vehicle into an open area. The elevation is also not displayed if the calculated elevation is zero or below sea level.
Problem
Solution
QRG