lock Alfa Romeo 8C 2010 Owner handbook (in English)

43
3
A
B
C
D
E
INSTRUMENTS AND CONTROLS
1) Air conditioning side vents2) Lower gearshift paddle “DOWN”3) Instrument panel4) Air conditioning upper vent5)
Sun radiation sensor
6)
Driver’s airbag
7)
Windscreen/headlight wiper/washer
control lever
8)
Upper gearshift paddle UP
9)
Central air conditioning/heating vents
10)
Radio/navigator
11)
Passenger’s airbag
12)
Air conditioning and heating system
controls
13)
Side windows vents
14)
Glove compartment
15)
Central dashboard controls
16)
Electric parking brake engagement/
disengagement lever
17)
Starter/steering wheel lock switch
18)
Horn control
19)
Steering wheel height and depth
adjustment lever
20)
Cruise Control lever, direction indicators
21)
Controls to the left of the steering wheel
22)
Engine start button
23)
Reverse gear engagement button
24)
AUTO mode button
25)
SPORT mode button
26)
VDC deactivation button
27)
WET mode button
28)
Hazard light buttonRef. 15 Central dashboard controls
A) Front left-hand power window controlB) Central locking control C) PARK OFF function button (see page.
137)D) Rear window opening control E) Front right-hand power window control

46
3
1354
27896
INFORMATION SHOWN
ON THE STANDARD PAGE 1) Time2) Outside temperature3) Failure/information symbol4) Trip odometer5) Total odometer6) Q-Select gearbox status 7) Engine oil temperature8) Coolant temperature 9) Fuel level gauge
The central area of the display indicating the
engine oil and coolant temperatures and the
fuel level remains active until another function
is activated or other information on the vehicle
status needs to be displayed.
RECONFIGURABLE
MULTIFUNCTION
DISPLAY The “reconfigurable multifunction display” shows
useful information while driving, in particular:With the key turned to MAR the following
information is immediately displayed for 2
seconds:
- Clock
- Outside air temperature
- Date
- Total odometer
- Trip odometer
- Q-Select gearbox status.
After two seconds the display will automatically
return to the standard page.

49
3
INSTRUMENTS AND CONTROLS
+
+–
–
Illumination Int.Speed Limit Light Sens. Reset Trip B
Clock
Mode 12/24 Date Indep.Boot Unlock Fda Door Lock Units LanguageBeep Vol.Service Beep Seatb.Quit setup
Day lights
+–
+–+–
+
–
+
–
+
–
+
–
+
–
+
–
+
–
+
–
+
–
+
–
+
–
+
–

51
3
INSTRUMENTS AND CONTROLS
Adjusting the sensing range of the twilight
sensor (Automatic low-beam)
This function allows you to adjust the sensing
range of the twilight sensor to 3 levels.
To adjust, proceed as follows:
- briefl y press the MENU button: the display
highlights the sensing range level previously
set
- press button + o – to adjust;
- press the MENU button briefl y to return to
the menu page or hold it down to return to
the standard screen page.Trip B reset mode (Reset TRIP B)
This function allows you to select Trip B reset
mode (automatic or manual).
For further information see the chapter “TRIP
button”.Clock adjustment (Clock)
This function allows you to adjust the clock.
To adjust the time proceed as follows:
- briefl y press the MENU button: the display
highlights the “hours”
- press button + o – to adjust;
- briefl y press the MENU button: the display
highlights the “minutes”
- press button + o – to adjust;
WARNING: When the button is pressed once
+/– the value increases/decreases by 1
unit. Holding the +/– button down, the value
automatically increases/decreases continuously
until you release the button. When you are close
to the desired value, release the button and then
press it briefly a few times until you reach the
desired value.- press the MENU button briefl y to return to
the main page or hold it down to return to
the standard page.

52
3
Clock mode (12/24 mode)
This function allows you to set the time display
mode in 12h or 24h format.
To set the clock proceed as follows:
- briefl y press the MENU button: the display
highlights 12h or 24h (depending on the
format previously set);
- press button + o – to select;
- press the MENU button briefl y to return to
the main page or hold it down to return to
the standard page.Date adjustment (Date)
This function allows you to adjust the date (year
- month - day).
To adjust the date proceed as follows:
- briefl y press the MENU button: the “year”
fl ashes on the display
- press button + o – to adjust;
- briefl y press the MENU button: the
“month” fl ashes on the display
- press button + o – to adjust;
- briefl y press the MENU button: the “day”
fl ashes on the display
- press button + o – to adjust;
WARNING: When the button is pressed once
+/– the value increases/decreases by 1 unit.
Holding the +/– button down +/–the value
automatically increases/decreases continuously
until you release the button. When you are close
to the desired value, release the button and then
press it briefly a few times until you reach the
desired value. - press the MENU button briefl y to return to
the main page or hold it down to return to
the standard page.

53
3
INSTRUMENTS AND CONTROLS
Rear window unlocking independent of the
doors opening (Ind. luggage compartment)
This function allows you to unlock the rear
window independently of the doors.
When this function is enabled, the rear window
can be unlocked by pressing the button
on
the electronic key (see section 4 in the chapter
“Rear window” ).
To make rear window unlocking independent of
(ON) or dependent on door unlocking (OFF),
proceed as follows:
- briefl y press the MENU button: the message
ON or OFF is displayed (depending on the
mode previously set);
- Press the + or – button to select;
- press the MENU button briefl y to return to
the menu page or hold it down to return to
the standard screen page.Driver’s door unlocking (Unlock. driver’s
door)
This function allows you to unlock only the
driver’s door by pressing the button
on the
electronic key.
When this function is active (ON) the other
doors can still be unlocked by pressing the door
unlocking button on the centre console.
To activate/deactivate (ON/OFF) this function,
proceed as follows:
- briefl y press the MENU button: the message
ON or OFF is displayed (depending on the
mode previously set);
- press button + o – to select;
- press the MENU button briefl y to return to
the menu page or hold it down to return to
the standard screen page.Automatic central door locking when the
vehicle is moving (Door locking)
When activated (ON), this function allows the
doors to lock automatically when a speed of 20
km/h is exceeded.
To activate/deactivate (ON/OFF) this function,
proceed as follows:
- briefl y press the MENU button: the message
ON or OFF is displayed (depending on the
mode previously set);
- press button + o – to select;
- press the MENU button briefl y to return to
the menu page or hold it down to return to
the standard screen page.
The LED on the button
will illuminate to
indicate that this function has been activated.

54
3
WARNING:If the vehicle is tested on the roller
test bench without any operator on board, check
in the vehicle Setup menu that the automatic
door locking function is disabled or that a
window is open, or that there is a second key
available outside the vehicle.
Unit of Measure (Unit of Measure)
This function allows you to set the unit of
measure for the mileage (km or mi), fuel
consumption (l/100 km, km/l or mpg) and
temperature (°C or °F).
DistanceTo set the desired unit of measure, proceed as
follows:
- briefl y press the MENU button: the display
highlights “km” or “mi” (depending on
what was previously set);
- press button + or – to select;
- press the MENU button briefl y to return to
the menu page or hold it down to return to
the standard screen page.
Fuel consumption If the unit of measure for the mileage is set to
“km” (see previous chapter), you can set the
unit of measure for fuel consumption (l/100
km, km/l or mpg).
If the unit of measure for the mileage is set to
“mi” (see previous chapter), the display will
show the fuel consumption in “mpg”.
In this case, the “Fuel consumption Unit of
Measure” option in the Setup menu can be
selected but is fixed on the indication in “mpg”.
To set the desired unit of measure, proceed as
follows:
- briefl y press the MENU button: the
display highlights “km/l” or “l/100 km”
(depending on the unit was previously set);
- press button + o – to select;
- press the MENU button briefl y to return to
the menu page or hold it down to return to
the standard screen page.

56
3
Scheduled maintenance (Service)
This function allows you to view when service is
due according to the mileage done.
To view this information, proceed as follows:
- briefl y press the MENU button: the display
shows when service is due in kilometres
or miles depending on the unit that was
previously set (see the chapter “Unit of
measure”);
- press the MENU button briefl y to return to
the menu page or hold it down to return to
the standard screen page.
WARNING: According to the Scheduled
Maintenance Plan, the vehicle must be
serviced every 10,000 km (or 6,000 mi). This
information is automatically displayed when the
electronic key is inserted in the ignition block,
starting from 2,000 km (or 1,200 mi) following
the service due date. The information will be
displayed in kilometres or miles depending on
the unit of measure set. When approaching the
scheduled maintenance (“Service”) due date,
inserting the electronic key in the ignition block,
a message will appear on the display followed
by the kilometres/miles left until the service due
date. Contact an Authorised Service Centre of
the Manufacturer’s Network where the staff
will perform the service operations according to
the Scheduled Maintenance or Annual Inspection
Plan and reset the mileage counter (Reset).
Buzzer reactivation for SBR (Seat Belt
Reminder) signalling (Seat belt beep)(where
provided)
This function is displayed only after the system
has been deactivated by an Authorised Service
Centre of the Manufacturer’s Network.
Automatic activation of the Day Running
Lights (where provided)
If this function is active, when the low-beams go
off, the DRLs come on, and vice versa, when the
low-beams come on the DRLs go off.
Exit menu
Select this item to return to the standard screen
page.

57
3
INSTRUMENTS AND CONTROLS
TRIP COMPUTER
General
When the electronic key is inserted in the ignition
block, the “Trip computer” allows you to view
the vehicle mileage features. This function
comprises the “Trip A” function which monitors
total mileage, and the “Trip B” function which
monitors trip mileage; the latter function is
“contained” in the total mileage function.
Both functions can be reset (reset when setting
off on a new trip).
Trip A and B allow you to view the following
values:
- Fuel range
- Distance travelled
- Average fuel consumption
- Instantaneous fuel consumption
- Average speed
- Travel timeValues displayed
Fuel rangeIt indicates the distance you can still travel with
the fuel left in the tank, assuming you continue
travelling at the same speed.
A specific message will be shown on the display
“----“ when the following events occur:
- when the fuel range is less than 50 km (or
30 mi)
- if the vehicle is stopped with the engine
running for more than 3 minutes.
Distance travelledIt indicates the distance travelled from the
beginning of a new trip.
Every time the battery is connected and at the
beginning of each new trip (reset) the display
indicates the value “0.0”.WARNING: If there is no information, all the
Trip Computer indicators will show “-” instead of
the value. When correct operation is resumed,
the counter resumes regular operation as well,
without resetting the values displayed prior to
the malfunction nor restarting the count from
zero as for a new trip.Average fuel consumptionThis is the average fuel consumption from the
beginning of a new trip.

59
3
INSTRUMENTS AND CONTROLS
The two modes of the Trip Computer can be
selected by briefly pressing the TRIP button;
Using the button “+” you can scroll the item
shown at the top of the display, while the button
“-” allows you to scroll the items displayed at
the bottom.
To go from the Trip A to the Trip B information,
briefly press the TRIP button.Procedure when setting off on a trip (reset)
Trip A and Trip B must be reset separately.
Reset Trip ATo reset Trip A, turn the key to MAR and press
and hold down the TRIP button for more than 2
seconds. WARNING: The counter will automatically be
reset only in the following cases:- when the “distance travelled” reaches
9999.9 km or when the “travelling time”
reaches 99.59 (99 hours and 59 minutes)
- Every time the battery is disconnected
and reconnected. When the trip is reset, a
warning message appears on the display.WARNING: When Trip A is reset, the “fuel
range” and “instantaneous consumption” values
are not reset.
Reset Trip BFor the Trip B values, through the Setup menu
you can select whether you wish to perform a
manual or an automatic reset procedure (see the
chapter “Setup menu” above):
- Manual reset: to manually reset Trip B,
press and hold down the TRIP button for
more than 2 seconds.
- Automatic reset: this occurs each time the
electronic key is inserted in the ignition
block.
When Trip B is reset, a warning message appears
on the display.WARNING: When Trip B is reset, the “fuel
range” and “instantaneous fuel consumption”
values are not reset.