brake ARIEL ATOM 2 2006 User Guide

34

HONDA FUSE PANELS
Fuse Box 1
Fuse Box 2
Relays

Fuse # Rating Description Relays

Fuse # Rating Description
F1 30A Battery F1 20A Ignition

R1
After Cool F2 15A Brake Light R1
Starter
F2 15A Fuel Pump
F3 15A Light Switch F3 20A High Beam
R2
Power Train F4 20A Power Point R2
Cooling Fan F4 20A Low Beam
F5 10A ALDL F5 No Fuse
ECM
R3
Cooling Fan
F6 10A ECM Battery+ R3
High
Beam F6 15A Power Train
F7 10A Hazard F7 15A BU Lamp
Switch
R4
Main
Relay F8 15A Horn R4
Low
Beam F8 2A Dash
F9 F9 15A Running
Lights
R5
F10 R5
Fuel
Pump F10 15A Turn Signal

35

FLUID LEVELS & TYPES FOR ATOMS WITH GM ENGINES
Fluid levels (GM engines)

Engine oil capacity: 6 quarts (5.20 L)
Transmission oil capacity: 67 ounces / 2.1 quarts (189 grams/1.99 L)
Brake fluid reservoir capacity: Fill to the indicated capacity line on the reservoir
Fuel tank capacity: 9.7 gallons (36.7 L)
Cooling system capacity: 2.75 gallons (10.395 L)
Supercharger after cooler coolant: 2 in. (apx.) below the filler cap when hot
Front lower A-arm ball joint grease: As needed

Fluid types (GM engines)
Engine oil: Mobil 1™ Synthetic 5-30
Transmission oil: Saturn Manual Transmission Lubricant
(The use of standard GL-4 lubricant is not recommended. )
Brake fluid: Dot 4
Clutch fluid: Dot 4
Fuel: Premium Unleaded
Cooling system: Dexcool (Dilute with water 50:50 if not pre-dilute d)
Supercharger after cooler coolant: Dexcool
Front lower A-arm ball joint grease: High quality bearing/suspension grease

36

FLUID LEVELS & TYPES FOR ATOMS WITH HONDA ENGINES

Fluid levels (Honda engines)

Engine oil capacity: 5.5 quarts (5.20 L)
Transmission oil capacity: 64 oz/2.1 quarts (189 grams/1.99 L)
Brake fluid reservoir capacity : Fill to the indicated capacity line on the reservoir
Fuel tank capacity: 9.7 gallons (36.7 L)
Cooling system capacity: 2.75 gallons (10.395 L)
Front lower A-arm ball joint grease: As needed

Fluid types (Honda engines)
Engine oil: 5-30 Conventional oil
Transmission oil: Honda/Acura Manual Transmission Fluid
Brake fluid: Dot 4
Clutch fluid: Dot 4
Fuel: Premium Unleaded
Cooling system: Acura/Honda Anti Freeze Coolant Type 2 (only avai lable premixed)
Front lower A-arm ball joint grease: High quality bearing/suspension grease

54

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE I: GENERAL REFERENCE

Component Service/Operation
Engine Oil
Check before every track event or every 1,000 miles (1,600 km). Change as necessary. Engine Oil Filter
Replace during every oil change. Engine Coolant
Check before every track event. Replace every 30,0 00 miles (48,000 km). Supercharger
Aftercooler Coolant Check before every track event. Replace every 30,0
00 miles (48,000 km). Air Filter Check before every track event. Clean and oil ever
y 5,000 miles (8,000 km). The Filtercharger®
element must be cleaned and serviced with K&N clean er and air filter oil per the prescribed routine
maintenance procedures as outlined in the product l iterature that accompanies the Filtercharger®. Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
Inspect for leaks before every track event; change every 10,000 miles (16,000 km). Brake Fluid
Inspect levels, condition, and any leakage before e very track event. Brake Rotors Replace when thickness decreases to 19mm, when puls
ation is noted, or if cracking or other physical
damage is found during inspection. Refer to the br ake bedding procedures on page12. Brake Pads Inspect for pad damage, thickness issues or deterio
ration before every event. Replace brake pads
when brake rotors are replaced. Refer to the brake bedding procedures on page12. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect lines for rubbing or scraping before every
track event. Exhaust System Use a wrench to inspect flange bolts for tightness
every 5,000 miles (8,000 km), check gaskets at
this time. Tires
Inspect tires for proper pressure and tread wear be fore and after every track event. Wheels Check wheel nut torque after the first 50 miles (80
km) of operation and before every track event
thereafter. Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check belt for cracking or abnormal wear every 3,00 0 miles (4,800 km). Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends.

55

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE II: BEFORE EVERY TRACK EVENT
Component Service/Operation
Engine Oil
Check before every track event. Change as necessar y. Engine Oil Filter
Replace during every oil change. Engine Coolant
Check before every track event. Supercharger
Aftercooler Coolant Check before every track event.
Air Filter
Check before every track event. Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
Inspect for leaks before every track event. Brake Fluid
Inspect levels, condition, and any leakage before e very track event. Brake Rotors Refer to the Brake Bedding Procedures on page12. I
nspect and replace when thickness decreases
to 19mm, when pulsation is noted, or if cracking or other physical damage is found during inspection.

Brake Pads Inspect for pad damage, thickness issues or deterio
ration. Replace brake pads when brake rotors
are replaced. Refer to the brake bedding procedure s on page12. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect lines for rubbing or scraping before every
track event. Exhaust System
Visually inspect exhaust flange bolts for tightness and/or damage. Tires
Inspect tires for proper pressure and tread wear be fore and after every track event. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends.

56

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE III: INITIAL 50 MILES (80 KM)
Component Service/Operation
Engine Oil
Check and fill as necessary. Engine Oil Filter
No service required. Engine Coolant
Check and fill as necessary. Supercharger
Aftercooler Coolant Check and fill as necessary.
Air Filter
No service required. Spark Plugs
No service required. Transmission Fluid
No service required. Brake Fluid
Check level. Fill as necessary. Brake Rotors
Refer to the brake bedding procedures on page12. Brake Pads
Refer to the brake bedding procedures on page12. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect for damage.
Exhaust System Visually inspect exhaust flange bolts for tightness
and/or damage, check gaskets visually to ensure
they have not developed a leak. Tires
Inspect for any unusual tread wear. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends. We recommend
replacement of all suspension rod ends at 3000mi or sooner based upon driving habits.

57

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE IV: INITIAL 300 MILES (480 KM)
Component Service/Operation
Engine Oil
Check and fill as necessary. Engine Filter
No service required. Engine Coolant
Check and fill as necessary. Supercharger
Aftercooler Coolant Check and fill as necessary.
Air Filter
No service required. Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
No service required. Brake Fluid
Check level; fill as required. Brake Rotors Inspect and replace when thickness decreases to 19m
m, when pulsation is noted, or if cracking or
other physical damage is found during inspection. Brake Pads Inspect for pad damage, thickness issues or deterio
ration. Replace brake pads when brake rotors
are replaced. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect for damage.
Exhaust System Visually inspect exhaust flange bolts for tightness
and/or damage, check gaskets visually to ensure
they have not developed a leak. Tires
Inspect for any unusual tread wear. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends. We recommend
replacement of all suspension rod ends at 3000mi or sooner based upon driving habits.

58

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE V: EVERY 1000 MILES (1600 KM)
Component Service/Operation
Engine Oil
Check before every track event or every 1,000 miles (1,600 km). Change as necessary. Engine Oil Filter
Replace during every oil change. Engine Coolant
Check before every event. Replace every 30,000 mil es (48,000 km). Supercharger
Aftercooler Coolant Check before every event. Replace every 30,000 mil
es (48,000 km). Air Filter
Clean and oil every 5,000 miles (8,000 km) Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
Change every 10,000 miles (16,000 km). Brake Fluid
Check level. Fill as needed. Brake Rotors Inspect and replace when thickness decreases to 19m
m, when pulsation is noted, or if cracking or
other physical damage is found during inspection. Brake Pads Inspect for pad damage, thickness issues or deterio
ration. Replace brake pads when brake rotors
are replaced. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect for damage.
Exhaust System Visually inspect exhaust flange bolts for tightness
and/or damage. Use a wrench to inspect flange
bolts for tightness every 5,000 miles (8,000 km), c heck gaskets visually to ensure they have not
developed a leak. Tires
Inspect for any unusual tread wear. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends. We recommend
replacement of all suspension rod ends at 3000mi or sooner based upon driving habits.

63


BRAKE PAD OPTIONS
Base Brake Package Parts

PART
DESCRIPTION BRAMMO PART
# MANUFACTURER AND
MFR. PART # QTY.
PBR 54mm floating front
caliper (left) AA-BK-002 PBR
BCB843199PL
1 PBR 54mm floating front
caliper (right) AA-BK-003 PBR
BCB843200PL 1 PBR 40.5mm floating
rear caliper w/ e-brake (left) AA-BK-004
PBR
BCB821020PL 1 PBR 40.5mm floating
rear caliper w/ e-brake (right) AA-BK-005
PBR
BCB821019PL 1 Single piece ventilated 10.3 rotor (262 x 21mm)
AA-BK-006
Galfer SKU#A24255VF
4
Front pads AA-BK-008 PBR
SS-7662X 1
Organic rear brake pads
for 1993-1997 Chevrolet
Camaro AA-BK-055
NAPA
SS-7301-M 1

64


Sport Brake Package Parts

PART
DESCRIPTION BRAMMO PART
# MANUFACTURER AND
MFR. PART # QTY.
Wilwood 4 x 35.1mm
Dynalite caliper (L & R) AA-BK-010 Wilwood
120-6806-R/L 2 PBR 40.5mm floating
rear caliper/parking brake (left) AA-BK-004
PBR
BCB821020PL 1 PBR 40.5mm floating
rear caliper/parking brake (right) AA-BK-005
PBR
BCB821019PL 1 Single piece ventilated
10.3 front rotor (262 x 21mm) AA-BK-006
Galfer
SKU#A24255VF 4 Front pads-Type 7112 Q
(street compound-4
pads)
AA-BK-015
Wilwood 15Q-6824K
1
Organic rear brake pads
for 1993-1997 Chevrolet
Camaro AA-BK-055
NAPA
SS-7301-M 1