wheel ARIEL ATOM 2 2006 User Guide

56

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE III: INITIAL 50 MILES (80 KM)
Component Service/Operation
Engine Oil
Check and fill as necessary. Engine Oil Filter
No service required. Engine Coolant
Check and fill as necessary. Supercharger
Aftercooler Coolant Check and fill as necessary.
Air Filter
No service required. Spark Plugs
No service required. Transmission Fluid
No service required. Brake Fluid
Check level. Fill as necessary. Brake Rotors
Refer to the brake bedding procedures on page12. Brake Pads
Refer to the brake bedding procedures on page12. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect for damage.
Exhaust System Visually inspect exhaust flange bolts for tightness
and/or damage, check gaskets visually to ensure
they have not developed a leak. Tires
Inspect for any unusual tread wear. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends. We recommend
replacement of all suspension rod ends at 3000mi or sooner based upon driving habits.

57

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE IV: INITIAL 300 MILES (480 KM)
Component Service/Operation
Engine Oil
Check and fill as necessary. Engine Filter
No service required. Engine Coolant
Check and fill as necessary. Supercharger
Aftercooler Coolant Check and fill as necessary.
Air Filter
No service required. Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
No service required. Brake Fluid
Check level; fill as required. Brake Rotors Inspect and replace when thickness decreases to 19m
m, when pulsation is noted, or if cracking or
other physical damage is found during inspection. Brake Pads Inspect for pad damage, thickness issues or deterio
ration. Replace brake pads when brake rotors
are replaced. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect for damage.
Exhaust System Visually inspect exhaust flange bolts for tightness
and/or damage, check gaskets visually to ensure
they have not developed a leak. Tires
Inspect for any unusual tread wear. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends. We recommend
replacement of all suspension rod ends at 3000mi or sooner based upon driving habits.

58

MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2

SCHEDULE V: EVERY 1000 MILES (1600 KM)
Component Service/Operation
Engine Oil
Check before every track event or every 1,000 miles (1,600 km). Change as necessary. Engine Oil Filter
Replace during every oil change. Engine Coolant
Check before every event. Replace every 30,000 mil es (48,000 km). Supercharger
Aftercooler Coolant Check before every event. Replace every 30,000 mil
es (48,000 km). Air Filter
Clean and oil every 5,000 miles (8,000 km) Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
Change every 10,000 miles (16,000 km). Brake Fluid
Check level. Fill as needed. Brake Rotors Inspect and replace when thickness decreases to 19m
m, when pulsation is noted, or if cracking or
other physical damage is found during inspection. Brake Pads Inspect for pad damage, thickness issues or deterio
ration. Replace brake pads when brake rotors
are replaced. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect for damage.
Exhaust System Visually inspect exhaust flange bolts for tightness
and/or damage. Use a wrench to inspect flange
bolts for tightness every 5,000 miles (8,000 km), c heck gaskets visually to ensure they have not
developed a leak. Tires
Inspect for any unusual tread wear. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends. We recommend
replacement of all suspension rod ends at 3000mi or sooner based upon driving habits.