AUDI A3 1998 8L / 1.G ATW Engine Motronic Fuel Injection Syst

24-20

Special tools and equipment

Procedure
VAG1598/31
- Switch ignition off.
- Remove Engine Control Module (ECM) Page 24
-23
.

- Connect VAG1598/31 test box to connector of wiring harness. Ground
(GND) clip at test box (not visible in illustration) must be connected to
Ground (GND). Relevant test procedures note whether Engine Control
Module (ECM) should also be connected to the test box.
- Perform test as described in relevant repair sequence.
Pa
ge 21 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-21

Note:
Important note:
After re-connecting the Engine Control Module
(ECM), the following work steps must be
performed:
- Perform adaptation of the Throttle Valve Control
Module -J338- Page 24
-121
.
- For vehicles with automatic transmission, the
kick down function must be adapted Page 24
-
139
.
- Check DTC memory and erase it if necessary
Page 01
-16
.
- If DTC memory was erased, readiness code
must be re-generated Page 01
-73
.

Note:
During the first adaptation phase, it is possible
that idle will be rough and vehicle may shake
lightly in drive mode.
Pa
ge 22 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-22

Procedure following interruption of
voltage supply


Note:
Important note:
After re-connecting voltage supply, the following
work steps must be performed:
- Perform adaptation of the Throttle Valve Control
Module -J338- Page 24
-121
.
- For vehicles with automatic transmission, the
kick down function must be adapted Page 24
-
139
.
- Check DTC memory and erase it if necessary
Page 01
-16
.
- If DTC memory was erased, readiness code
must be re-generated Page 01
-73
.

Note:
During the first adaptation phase, it is possible
that idle will be rough and vehicle may shake
lightly in drive mode.
Pa
ge 23 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-23

Engine Control Module (ECM), replacing


Special tools and equipment

or
Removing
VAS5051 with VAG5051/1VAG1551 with VAG1551/3A
- Connect VAS5051 tester or VAG1551 scan tool and select control
module for engine electronics using "address word" 01 Page 01
-10
.
Ignition must remain switched on.
4B0906018Q
1.8 L R4/5VT
G 0008
Codin
g 07551
WSC 12345

VAG1551 Scan Tool (ST) display indicates control module identification,
e.g.
- Always allow display of control module identification first and print it out
Page 01
-13
.
- Compare coding with coding versions Page 01
-64
.
Pa
ge 24 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-24

- Switch ignition off.

- Pull off rubber seal of plenum chamber cover in direction of arrow.
- Remove cover -1- toward front.

- Remove Heater Core E-box cover (arrows).
Pa
ge 25 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-25


- Using a screwdriver, carefully pry off retaining bracket (arrow).

Note:
Adaptation values are erased when connector is disconnected from the
Engine Control Module (ECM), DTC memory content remains intact. - Disengage connector catches (arrows) and disconnect harness
connectors -1- and -2- from control module.
- Remove Engine Control Module (ECM).
Pa
ge 26 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-26

Installing
Installation is reverse of removal, noting the
following:

Note:
Important note:
After installing new Engine Control Module
(ECM), the following work steps must be
performed:
- Check DTC memory and erase it if necessary
Page 01
-16
.
- Perform adaptation of the Throttle Valve Control
Module -J338- Page 24
-121
.
- Observe notes for coding new Engine Control
Module (ECM) Page 01
-62
.
- For vehicles with cruise control (discernable at
steering column), switch this free in ECM:

Repair Manual, Electrical Equipment On
Board Diagnostic (OBD), Repair Group 01; OBD for cruise control system

- For vehicles with automatic transmission, the
kick down function must be adapted Page 24
-
Pa
ge 27 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

139
.
Pa
ge 28 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-27
- Adapt immobilizer to Engine Control Module
(ECM):

Repair Manual, Electrical Equipment On
Board Diagnostic (OBD), Repair Group 01; OBD of immobilizer
- variable code; adaptation after
replacing Engine Control Module (ECM)

- Generate readiness code Page 01
-73
.

Note:
During the first adaptation phase, it is possible
that idle will be rough and vehicle may shake
lightly in drive mode.
Pa
ge 29 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-28

Idle speed (RPM), checking


Special tools and equipment

or
Test requirements:
VAS5051 with VAG5051/1VAG1551 with VAG1551/3AExhaust system free of leaks. Coolant Temperature at least 80 C. Electrical consumers switched off (radiator fan must NOT run during
test). A/C switched off. No pressure gauge connected. Vehicles with automatic transmission Selector lever in P or N.
Pa
ge 30 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1