function selector AUDI A3 2008 8P / 2.G Infotainment MMI Operating Manual

Using the telephone91
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Press the control button for Dial. The telephone number
entered will be dialled.
Should you have entered a telephone number incorrectly, you can
delete the telephone number you have entered into the speller by
pressing the control button .
Note
•DTMF tones can be entered directly using the speller or loaded
from the telephone numbers stored in the memory lists
page 91.
•The audio source is muted automatically when you make or
receive telephone calls. The mute symbol
page 42, fig. 31 will
then appear in the status line.
•If you activate the voice guidance option off (phone)* in the navi-
gation* function you will not hear any navigation cues while you are
talking on the telephone*
page 119.
•If the MMI display was switched off, it will be switched on auto-
matically for the duration of the telephone call.
Applies to vehicles: with Bluetooth car telephone kit or phone pre-installation
From a list
Important: The telephone mode must be activated

page 26.
Finding and calling a telephone number from a
list
– Press the Memory control button.
– Turn the rotary pushbutton and select Numbers dialled,
Directory, Phone book, Received calls or Missed calls.
– Press the rotary pushbutton. The telephone numbers in
the selected list will appear in the MMI display.
– Turn the rotary pushbutton to the telephone number you
wish to select.
– Press the rotary pushbutton. The selected telephone
number will be entered into the speller automatically.
– To start the call, turn the speller to OK and press the
rotary pushbutton, or
– Press the control button for Dial.
Calling up the Numbers dialled list (shortcut) and
calling a number
– Press the function selector button marked . The
speller will appear on the MMI display. There will be no
phone number in the entry space of the speller.
– Press the control button for Dial. The Numbers dialled list
will appear in the MMI display.
– Turn the rotary pushbutton to the telephone number you
wish to select.
– Press the rotary pushbutton. The selected telephone
number will be entered into the speller automatically.
RETURN
Fig. 85 Selecting a
telephone number
from a list
TEL










Using the telephone 96
Switching between calls*13)
You can switch between two phone calls (one of them will be on
hold at any given time). The MMI display shows the active call, the
call on hold and the length of time for the connection.
Press the control button for End call to end whichever call is
currently active. The call on hold will remain in the hold queue.
Conference calling*
13)
Up to five callers can take part in a conference (depending on the
network service).
Select Join conference
page 95, fig. 89 to set up a conference. The
call on hold and the active call are added to the conference.
To set up a further call, select Hold to place all the members of an
existing conference on hold. Then press the control button for
Options or the button on the control console to close the
Options menu. Now enter a telephone number using the speller

page 90, fig. 83. Select OK or Dial to start dialling. To add this
caller to the existing conference, select Conference.
Select Resume if you want to retrieve all callers of an existing
conference from the hold queue. The Show conference participants

page 95, fig. 90 option allows you to display the callers.
Note
•The option Call waiting must be activated for you to be made
aware of incoming calls during a conversation
page 97. This
option depends on your mobile network service provider.
•The options available during a call may vary depending on the
mobile network service provider.
Applies to vehicles: with Bluetooth car telephone kit
Telephone settings
– Select: Function selector button > function selector
button > Telephone settings.
Set ring tone*14)
The selected ring tone is played and is stored when you close the
submenu.
Bluetooth settings*
•Search for mobile phone*14) - to find and list any Bluetooth
mobile phones within range.
•Bluetooth devices - to display a list of Bluetooth devices bonded
to the MMI system. The Bluetooth symbol marks the Bluetooth
device which contains the SIM card and which is actively connected.
•Delete ext. Bluetooth dev. - to delete all bonded mobile phones.
Bonded handsets* (e.g. “AUDI BTHS”) have to be deleted one at a
time. To delete bonded Bluetooth devices one at a time, choose a
device and select Delete this device.
•Bluetooth name - to change the name of the vehicle base station
on your car telephone kit (“AUDI BTA”).
•PIN for handsfree mode15) - to change the factory default (1234).
This PIN number has to be entered when you bond a mobile phone
with the Hands-Free Profile
page 28.
•Discoverability - to switch the car telephone discoverability on or
off. This setting determines whether the vehicle base station can be
detected by a mobile phone or handset*. If you select auto, the
vehicle base station can be discovered by mobile phones or the
handset* for a period of about five minutes while the car is
stationary and the key is in the ignition. Discoverability is switched
off after this period. Mobile phones which have already been
bonded can connect via Bluetooth even when discoverability is
RETURN
14)Applies to mobile phones with SIM Access Profile.15)Applies to mobile phones with Hands-Free Profile.
TEL
SETUP





!




Using the telephone97
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control deactivated. Once you have bonded your mobile phone, you should
switch this function off to prevent your car telephone (vehicle base
station) from being discovered by other users.
Default settings
This function returns the car telephone settings to the factory
defaults. This will delete your user data, including the phone books
stored in the memory
page 29, any bonded Bluetooth devices

page 24 and your mailbox number.
Call information*
14)
This function determines whether the vehicle occupants can see the
telephone numbers in the MMI display.
•on - the telephone numbers or names are shown in the MMI
display. All call lists are deleted when you switch on this function.
•off - asterisks ******** appear in the MMI display in place of tele-
phone numbers and names during inbound and outbound calls.
Telephone numbers stored on the MMI cannot be accessed. The call
lists are not updated.
Sound focus
•front - to direct the audio output during a telephone call to the
front loudspeakers.
•centre - to direct the audio output during a telephone call to the
front and centre loudspeakers.
Shutdown delay
•Activated (ticked ) - the telephone system remains active for a
period (factory default setting) after you switch off the MMI. You can
still make calls during this period.
•Deactivated (not ticked) - the telephone system shuts down
when you switch off the MMI. In this case, you can use a twin card
shortly after leaving the vehicle
page 30.
Note
The telephone settings depend on your mobile network service
provider.
Applies to vehicles: with Bluetooth car telephone kit
Call options
– Select: Function selector button > function selector
button > Call options.
Call waiting*16)
•Activate - when you are on the phone an audible tone will tell you
if a caller is trying to reach you.
•Deactivate - when you are on the phone you will not be informed
if a caller is trying to reach you.
•Status - to display whether the call waiting function is on or off.
Transmit caller ID*
16)
•Activate - to transmit your telephone number with outbound
calls.
•Deactivate - to suppress your telephone number during
outbound calls.
•Network-dependent - to use the setting agreed in your mobile
network service contract.
•Check status - to check whether the setting for this function is
activated, deactivated or network-dependent.
Automatic redial
•on - to dial a number automatically up to five times if the line is
engaged. Select End call if you want to cancel the automatic redial
function.
16)Applies to mobile phones with SIM Access Profile.
TEL
SETUP










Using the telephone 98
•off - a number is not redialled automatically if the line is
engaged.
Auto call answer
•on - an incoming call is answered automatically shortly after it is
received.
•off - an incoming call is not answered automatically.
Note
The call options depend on your mobile network service provider.
Applies to vehicles: with Bluetooth car telephone kit
Security settings
– Select: Function selector button > function selector
button > Security settings.
Automatic PIN recognition
•on - to save the PIN code of the SIM card the first time you enter
it on the MMI. In this case, you don't have to enter the PIN code
every time your mobile phone reconnects via Bluetooth. You can
save the PIN codes of four different SIM cards on the MMI.
•off - to delete all PIN numbers already stored on the MMI.
PIN query
•Activate PIN query - the telephone system asks for the PIN every
time you switch it on. If Automatic PIN recognition is activated, the
system does not ask you to enter the PIN explicitly.
•Deactivate PIN query - the telephone system does not ask for the
PIN when you switch it on. The Automatic PIN recognition setting is
ignored in this case. Some SIM cards do not allow the PIN query to
be deactivated.Changing PIN code
First enter the existing PIN code for your SIM card. The PIN can only
consist of numbers from 0 to 9. The new PIN has to be entered twice,
as a precautionary measure, and is stored on the SIM card.
If you change the PIN when the SIM card is in a connected mobile
phone with SIM Access Profile, you will have to enter the PIN again
on the mobile phone after the Bluetooth connection between the
car telephone kit and the mobile phone is terminated. Otherwise
you will not be available.
Call barring
The call barring function requires a password. You can obtain the
password from your mobile network service provider.
•Bar outgoing calls - to set up access restrictions for outbound
calls.
•Bar incoming calls - to set up access restrictions for inbound
calls.
•Deactivate call barring (all) - to cancel all restricted access
settings.
Note
The call barring options depend on your mobile network service
provider.
Applies to vehicles: with Bluetooth car telephone kit
Mailbox number
– Select: Function selector button > function selector
button > Mailbox number.
Enter the mailbox number using the speller and select OK to store it.
To delete the mailbox number, select Del in the speller and confirm
with OK.
TEL
SETUP
TEL
SETUP










Using the telephone99
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Once the number has been stored, you can call the mailbox by
pressing the control button for Memory.
Note
This service must be set up beforehand. For more information,
contact your service provider.
Applies to vehicles: with Bluetooth car telephone kit
Calling the mailbox
– Select: Function selector button > control button
Memory > Call mailbox.
The mailbox number must be stored first
page 98. This service
must be set up and activated on your mobile network before you
can use it. For more information, contact your service provider.
Applies to vehicles: with Bluetooth car telephone kit
Forwarding calls
– Select: Function selector button > function selector
button > Call forward.
Forward phone calls17)
Incoming calls are forwarded to your mailbox or another number.
You can choose from the following:
•Forward all calls - to forward all incoming phone calls.
•Forward if busy - to forward calls when you are already talking on
the phone.
•Forward if not available - to forward calls when the phone is
switched off.
•Forward if no answer - to forward calls that you do not answer.
Forward fax calls
17)
Incoming fax calls are forwarded to the specified number.
Forward data calls
17)
Incoming data calls are forwarded to the specified number.
Deactivate all fwd settings
17)
All call forward settings can be deleted at once.
Applies to vehicles: with Bluetooth car telephone kit
Network selection
– Select: Function selector button > function selector
button > Network selection.
Login18)
•automatic - your telephone will automatically log into your
mobile service provider network.
•manual - a list of all available networks will appear on the display.
Select a network.
Network selection
18)
The networks for your present location are listed. You can choose
any of the available networks. This function can be used when the
manual login setting is activated.
Note
For further information about networks, please contact your mobile
network service provider.
17)Applies to mobile phones with SIM Access Profile.
TEL
TEL
SETUP
18)Applies to mobile phones with SIM Access Profile.
TEL
SETUP










Using the telephone 100
Applies to vehicles: with Bluetooth car telephone kit
Memory settings
– Select: Function selector button > function selector
button > Memory settings.
Delete last calls*19)
•Delete numbers dialled - to delete individual telephone numbers
or the complete call list.
•Delete received calls - to delete individual telephone numbers or
the complete call list.
•Delete missed calls - to delete individual telephone numbers or
the complete call list.
Sort call lists
The telephone numbers in the call lists are sorted by the time of the
call. If this function is activated, the list is sorted in reverse order.
Phone book used
•SIM - SIM card entries are loaded onto the car telephone kit and
displayed on the MMI.
•Telephone - phone book entries on the mobile phone are loaded
onto the car telephone kit and displayed on the MMI.
•SIM+Tel - SIM card entries and phone book entries on the mobile
phone are loaded onto the car telephone kit and displayed on the
MMI.
Note
•The memory settings depend on your mobile network service
provider.
•Depending on your mobile phone, it may not be possible to
access the SIM card entries or phone book entries on your mobile phone. For further information, please ask an Audi dealer or
specialist retailer.
Applies to vehicles: with Bluetooth car telephone kit and handset or mobile phone with SIM
Access Profile
Text messages
– Select: Function selector button > control button
Te x t m s g.
If enough memory is available on your SIM card, an incoming text
message can be saved and displayed.
The MMI display shows text messages which are stored on the SIM
card. Depending on the type of mobile phone, your text messages
are stored either on the SIM card or in the mobile phone memory. If
your text messages are stored in the mobile phone memory, they
cannot be displayed on the MMI.
Unread text messages
20)
The envelope symbol in the status line indicates that you have one
or more unread text messages. These are displayed together with
the date, time and telephone number or name.
Read text messages
20)
These are displayed together with the date, time and telephone
number or name.
Delete all text messages
20)
•Delete read text msgs
•Delete received text msgs - to delete read and unread text
messages.
•Delete all text messages - to delete all text messages on the SIM
card.
19)Applies to mobile phones with SIM Access Profile.
TEL
SETUP
20)Applies to mobile phones with SIM Access Profile.
TEL










Using the telephone 102
Sound focus
•front - to direct the audio output during a telephone call to the
front loudspeakers.
•centre - to direct the audio output during a telephone call to the
front and centre loudspeakers.
Shutdown delay
•Activated (ticked ) - the telephone system remains active for a
period (factory default setting) after you switch off the MMI.
•Deactivated (not ticked) - the telephone system shuts down
when you switch off the MMI. In this case, you can use a twin card
shortly after leaving the vehicle.
Applies to vehicles: with phone pre-installation
Call options
– Press the > buttons on the MMI control
console and select Call options on the MMI.
Automatic redial
•on - to dial a number automatically up to five times if the line is
engaged. Select End call if you want to cancel the automatic redial
function.
•off - a number is not redialled automatically if the line is
engaged.
Auto call answer
•on - an incoming call is answered automatically. It is possible to
decline an incoming call (Ignore) before the auto answer function
responds.
•off - an incoming call is not answered automatically.
Applies to vehicles: with phone pre-installation
Mailbox number
– Press the > buttons on the MMI control
console and select Mailbox number on the MMI.
Enter the mailbox number using the speller and select OK to store it.
To delete the mailbox number, select Del in the speller and confirm
with OK.
Once the number has been stored, you can call the mailbox by
pressing the control button for Memory.
Note
This service must be set up beforehand. For more information,
contact your service provider.
Applies to vehicles: with phone pre-installation
Calling the mailbox
– Select: Function selector button > control button
Memory > Call mailbox.
The mailbox number must be stored first
page 102. This service
must be set up and activated on your mobile network before you
can use it. For more information, contact your service provider.
Applies to vehicles: with phone pre-installation
Memory settings
– Press the > buttons on the MMI control
console and select Memory settings on the MMI.
TELSETUP
TELSETUP
TEL
TELSETUP











Navigation105
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Applies to vehicles: with navigation system
Activating navigation mode
Important: The MMI system must be switched on

page 40, and a navigation DVD must be inserted in the
drive
page 14.
– Press the function selector button. The entry space

fig. 91, the Route plan menu
fig. 93 or the naviga-
tion menu that was last activated will appear on the MMI
display.
The menu that was active when you last used the navigation system
will appear on the MMI display. Call up the entry space or the Route
plan menu by pressing the function selector button again
(while in navigation mode).
Note
•Press the right-side thumbwheel on the multi-function steering
wheel*
page 128 to have the last spoken voice guidance cue
repeated.
•You can also start the navigation in demo mode
page 120 if
you want a simulation.
Entering a destination
Applies to vehicles: with navigation system
Entering a route with and without stopover(s)
You can choose whether you would like to enter a single
destination (Route without stopover) or up to three stopo-
vers (Route with stopover).
Important: The navigation mode must be activated

page 105, and an entry space for a single destination

fig. 91 or a route plan
fig. 93 must be displayed.
Fig. 91 Entry space
NAV
NAV
Fig. 92 Route with
stopover
Fig. 93 Route plan










Navigation107
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control If you would like to find a special destination without entering a
specific town, select Special destination
page 116 from the navi-
gation menu after selecting the country.
Selecting “Select destination on map”
You can also set your destination via the map display.
Once the map for the selection of a destination is displayed, cross-
hairs will appear in the centre of the corresponding town. You can
then specify a new destination by moving the crosshairs vertically
and horizontally
page 109.
Applies to vehicles: with navigation system
Single destination (route without stopover)
For a single destination the country and town must
always be specified. You can specify the destination
further by entering an address or a special destination.
Important: The system must be set to Route without
stopover
page 105.
– If the entry space
page 105, fig. 91 does not appear in
the MMI display, press the function selector button
marked .
– Turn the rotary pushbutton and select Country.– Press the rotary pushbutton. Using the rotary push-
button, you can now select a country from the list and
then copy it into the entry space by pressing the rotary
pushbutton.
– Turn the rotary pushbutton and select To w n / Z I P.
– Press the rotary pushbutton. The speller will appear on
the MMI display
page 43.
– Enter the town or the ZIP code via the speller.
– To complete the entry, turn the rotary pushbutton to
Centre (end entry) and press to confirm, or
– To enter additional data on the navigation destination,
turn the rotary pushbutton to Street, Special destination
in town or Select destination on map and press to
confirm.
– Enter the additional information.
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
To add a house number or intersection after entering the destina-
tion, select the line
fig. 95 and complete your entries.
Note
•If your navigation destination contains special characters such
as the dashes in “Stratford-upon-Avon”, simply switch between the
speller for letters and the speller for numbers
page 43.
Fig. 95 Entering a
house number/inter-
section
NAV
A1










Navigation 108
•To have the last route guidance cue repeated, press the control
button Nav-Info
page 118 or the right thumbwheel on the multi-
function steering wheel
page 129.
Applies to vehicles: with navigation system
Route plan (route with stopovers)
You can enter up to three stopovers and a final destina-
tion in the route plan.
Important: The system must be set to Route with stopover

page 105.
– If the Route plan
fig. 96 does not appear in the MMI
display, press the function selector button .
– Turn the rotary pushbutton and select Destination.
– Press the rotary pushbutton. The entry space will appear
in the MMI display
page 105, fig. 91.
– Enter the navigation destination
page 107.
– To enter stopovers, turn the rotary pushbutton to Stop 1,
Stop 2 or Stop 3.– Press the rotary pushbutton. The entry space will appear
in the MMI display
page 105, fig. 91.
– Enter the stopovers (see
page 107).
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Note
•If you would like to change your route plan, no problem! Simply
use the rotary pushbutton to select the destination or stopover and
then press the rotary pushbutton. Now you can change or delete the
destination or stopover or move the stopover.
•If your navigation destination contains special characters such
as the dashes in “Stratford-upon-Avon”, simply switch between the
speller for letters and the speller for numbers
page 43.
•To have the last route guidance cue repeated, press the control
button Nav-Info
page 118 or the right thumbwheel on the multi-
function steering wheel
page 129.
Applies to vehicles: with navigation system
Changing the route guidance
You can change a route guidance plan at any time.
Important: The route guidance function must be activated

page 105.
– Press the function selector button.
– Enter new information for the single destination or a
destination/stopover of the route plan
page 105.
Fig. 96 Route plan
NAV
NAV