check engine AUDI A3 2015 Owner's Guide

222 Checking and Fill in g
and then the negative cable . Never inter­
change the cables -this could start a fire!
- Never charge a frozen or a thawed-out
battery. It could explode! If a battery has
frozen, then it must be replaced. A dead battery can freeze over at 32°F (0°C).
- Make sure the vent hose is always attach­
ed to the opening on the side of the bat­
tery.
- Never use batteries which are damaged.
There is the danger of an explosion! Al­
ways replace a damaged battery.
&_ WARNING
California Propos ition 65 Warning:
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
t ive p roblems. Wash hands after han­
dling.
(D Note
- Do not d isconnect t he veh icle battery
when the ignition is on or when the en­
gine is running, otherwise, you will dam­
age ele ctron ic componen ts in the elec tri ­
ca l system.
- If your vehicle is going to stand for a
l ong period of time wi thout being driven,
protect the battery from "freezing", oth­
e rwise it w ill be damaged and wi ll then
have to be replaced.
Battery charging
Starting the engine requires a well charged battery.
F ig . 1 54 Engine co mpartment : connectors for a charg­
er and jump start cab les
Alwa ys read and heed all WARNINGS below
c> &. and c> &. in Working on the battery on
page 221.
.. Switch off the ignition and all electrical con­
sumers.
.. Make sure the area is well ventilated when
you charge the battery .
.. Open the eng ine hood
r=;, page 211 .
.. Open the red cover on t he positive pole
r=;, fig. 154 .
.. Clamp the ch arger term inal clamps as in­
structed on the
batter y terminal (+ ) and on­
ly o n the
body ground po int (-) .
.. On ly now plug the mains lead for the charg­
ing equ ipment into the wa ll outlet and turn
iton
c> &, .
.. Make sure th e charging rate is not over
30 amps /14 .8 volts .
.. When the battery is fully charged: Turn the
charg ing equipment off and remove the
mains lead from the wall ou tlet .
.. Now remove the clamps for the cha rging
equipment .
.. Close the red cover on the positive pole .
.. Close the hood
~ page 211.
A d ischarged bat tery can freeze at tempera ­
tu res of only 32 F
0 (0 °C). Allow a frozen bat­
tery to thaw completely before attempting to charge it
r=;, .&, . However, we recommend not
using a thawed battery again because the bat­
te ry casing can be cracked due to ice forma-
t ion and can leak battery acid . ..,.

Battery charging (Ma ximum charging rate
o f 30 am ps/ 14.8 volt s)
When charging at
low voltages (e.g . with a
tri ckle ch arg er), the batte ry cables do not
have to be d isconnected first. The battery
caps should
not be opened when charging a
battery .
It is not necessary to remove the battery from
the luggage compartment, and it is also not
necessary to disconnect the cables.
F ast charging th e battery (charging rate
a bo ve 14 .8 volt s)
For technical reasons do not use a battery
charger that uses voltage greater than 14.8
volts to charge your ve hicle 's battery .
A WARNING
Charging a battery can be dangerous .
- Always follow the operating instructions
provided by the battery charge r manu­
fact urer when charging your battery .
- Never charge a frozen battery . It may ex ­
plode because of gas t rapped in the ice .
Allow a frozen battery to thaw out first.
- Do not reuse batteries which we re fro ­
zen . The batte ry housing may have
cr acked and weakened whe n the battery
froze.
- Charge the battery in a we ll ventilated
area. Keep away from open flame o r ele c­
trical spark. Do not smoke. Hydroge n gas
generated by the battery is exp losive.
- T o redu ce the danger o f explosion , never
conne ct or disconnect cha rger cables
wh ile the charger is operating .
- F ast charg ing a battery i s dangerous and
sho uld on ly be attempted by a compe­
tent technician with the proper eq uip ­
me nt.
- Battery acid that may spill during charg ­
ing should be washed off with a so lution
of warm water and ba king soda to neu­
tralize the acid.
Checking and Fillin g 223
@ Note
Neve r use a fast charger as a booster to
start the eng ine . This w ill seriously dam­
age sens itive e lectronic components, such
as contro l units, relays, radio, etc., as well
as the batte ry charger .
Battery replacement
The new ba ttery mus t hove the some specifi­
cations and dimensions as the original equip­
ment battery .
Intelligent energy management in your vehi­
cle is responsible for distributing the electri­
ca l ene rgy throughout your vehicle
~ page 190 . The intelligent energy manage­
ment system will keep the engine battery
c h arged better than vehicles without this sys­
tem. To make sure the addition al ele ctri cal e n­
ergy is ava ilab le once again after yo u have
changed the batte ry, we recommend that you
insta ll batteries of the same type an d manu­
facture on ly (the same as those insta lled at
the time your veh icle was delivered) . Specif i­
cations are listed on the battery housing. Your
authorized dea ler must code the battery in
the ene rgy management system to enab le you
to use the ene rgy management functions cor­
re ct ly afte r repla cing the battery.
The new battery must have the same capacity,
vo ltage ( 12-volts) , amperage, construction
and plug sea ling .
When install ing the battery, make sure the ig­
nition and a ll electrical consumers are switch ­
ed off .
~ Note
Make sure the ventilat ion hose on the side
of the battery is con nected, otherwise
fumes o r batte ry acid can lea k out.
@) For the sake of the environment
Because of the prob lem of proper disposal
of a battery, we recommend your author ­
i zed Audi dealer change the battery for
you. Batteries contain sulfur ic acid and ..,.
•
•
•

224 Checking and Filling
lead and must always be disposed of prop­
erly in compliance with a ll environmental
regulations. D isposing of vehicle batteries
improperly is very dangerous to the envi­
ronment.
Windshield washer
fluid container
Fig. 155 Engine co mp artmen t: cove r on the wind shield
an d h ead ligh t* washer fluid rese rvo ir
The washer flu id container is marked with the
symbol Won its cap
~fig. 155, ~page 212 ,
fig. 149 .
.. Before you check anyth ing in the engine
compartment,
always read and heed all
WARNINGS ~page 210 .
.. Lift the filler cap tongue to add washer flu­
id. You can fill the container to the top .
.. Press the cap back onto the f iller neck after
filling the container.
You can find the reservoir
ca pa city in the table
in ~
page 266 .
C lean water should be used when filling up.
If
possible, use soft water to prevent scaling on
washer jets. A lways add a glass cleaner solu­
tion (with frost protection in the winter) .
@ Note
- Do not mix engine coolant antifreeze or
any other additives to fill up the wind­
shield washer reservoir.
- Do not use a glass cleaner that contains
paint solvents, there is a risk of damag­
ing the paint.

Fuses and bulbs
Electrical fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through.
Fig. 17 4 Steering column area: cover
Fig. 175 Left side of the engine compartment: fuse
cover
Fuses i n the interio r
The fuses are behind the cover in the steering
column area
¢fig. 174.
•Turnoff the ignition and the fai led e lectrical
equipment.
• Check the following table to see which fuse
belongs to the equipment¢
page 256.
• Remove the cover: ¢ fig. 174.
• Remove the plastic clip from the fuse panel
cover in the eng ine compartment
c;, fig. 175.
• Remove the blown fuse using the plast ic
clamp and replace the fuse with an ident ica l
new one.
• Install the cover .
Fuse s in th e en gine compar tmen t
•Turnoff the ignition and the failed electrical
equipment .
Fuse s and bulb s 255
• Check the fo llowing tab le to see which fuse
be longs to the equipment
c:;, page 257.
• Remove the fuse panel cover¢ fig. 175.
• Remove the plastic clip from the fuse pane l
cover
c;, fig. 175.
• Remove the blown fuse using the plastic
clamp and replace the fuse with an identical
new one .
The indiv idual circu its are protected by safety
fuses . The fuses are located under the steer ­
ing wheel beh ind a cover and in the left s ide of
the engine compartment .
.&_ WARNING
-
Do not repair fuses and never replace a
blown f use with one that has a hig her amp
rating. Th is can cause damage to the elec­
trica l system and a fire .
(D Note
-If there a re multiple fuse values in a cell
in the fo llow tables, for examp le
5/10/20, it is because of equipment -re ­
lated differences . Replace the burned
fuse with an identical new one.
- If a new f use should burn out again
shortly after you have installed it, have
the electrical system checked by your au­
thorized Aud i dealer or qualified repair
facility as soon as possible.
(!) Tips
- The following tab le does not list fuse lo­
cations that are not used .
- Some of the following tables on ly app ly
to in certain models or options.

Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
using a
pair of jumper cables to start the en­
gine.
Jumper cables
Use only jumper cables of sufficiently large
cross section to carry the starter current safe­
ly. Refer to the manufacturer's specifications.
Use only jumper cables with
insulated termi­
nal clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
injury. Follow the instructions below for
safe handling of your vehicle's battery.
- Always shield your eyes and avoid lean­
ing over the battery whenever possible.
- A discharged battery can freeze at tem­
peratures just below 32 °F (0 °C). Before
Emergency situations 259
connecting a jumper cable, you must
thaw the frozen battery completely, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin. Flush any contacted area with
water immediately .
- Improper use of a booster battery to start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with a low acid level in the battery.
- The voltage of the booster battery must
also have a 12-volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery . Use of batteries of different voltage
or substantially different "Ah" rating
may cause an explosion and personal in­
JU ry.
- Never charge a frozen battery. Gas trap­
ped in the ice may cause an explosion.
-Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batteries of different voltage or
substantially different capacity (Ah) rat­
ing may cause an explosion and injury.
The capacity (Ah) of the booster battery
should not be lower than that of the dis­
charged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
¢ page 210.
(D Note
-Applying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
control units, relays, radio, etc.
- There must be no electrical contact be­
tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected. ..,. •
•
•

10. With the engines running, remove the ca­
b les in
reverse order of the way they were
installed. Make sure the cables do not get
caught in moving engine components.
11. Switch the heater fan and rear window de-
froster off .
12 . C lose the battery cover.
The battery is vented to the outside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connect ­
ed with their metal parts in full contact with
the battery termina ls.
.&, WARNING
To avoid serious pe rsonal injury and dam­
age to the vehicle, heed all warnings and
instructions of the jumper cable manufac­
turer. If in doubt, ca ll for road service .
- Jumper cables must be long enough so
that the vehicles do not touch.
- When connecting jumper cables, make
surethattheycannotgetcaughtinany
moving parts in the engine compart­
ment.
- Be fore you check anything in the engine
compartment, always read and heed all
WARNINGS
~ page 210.
(D Note
Improper hook-up of jumper cables can ru­
in the generator.
- Always connect POSITIVE( +) to POSI ­
TIV E(+), and NEGA TIVE( -) to NEGATIVE
( - ) ground post of the battery manager
control un it .
- Check that all screw plugs on the battery
ce lls are screwed in firmly. If not, tighten
plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note th at the procedure for con­
necting a jumper cable as described
above applies specifically to the case of
your vehicle be ing jump started. When
you are giv ing a jump start to another ve ­
hicle, do
not connect the negat ive( -) ca­
ble to the negat ive( -) term inal on the
discharged battery@~
fig. 179. In-
-
Em erg en cy si tuation s 261
stead, secure ly connect the negative( -)
cable to either a solid meta l component
that is firmly bo lted to the engine block
or to the engine block itself. If the bat­
tery that is be ing charged does not vent
to the outside, escaping battery gas could ig nite and explode!
- Make sure that the connected positive
terminal clamps have sufficient contact
with metal.
- Do not use the battery negat ive terminal
for jump start ing or a malfunct ion could
occur in the vehicle electrical system .
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
The following information is to be used by
comme rc ial tow truck operators who know
how to operate their equipment safely.
-Ne ver t ow your A udi. Towing will caus e
da mage to the engin e and tr an smi ssion .
- Nev er wrap the safet y chains or wi nch ca­
ble s around the brak e lines.
- To p revent unnecessar y damage , your Aud i
must be t ran spor ted with a flat bed truck.
- To lo ad the vehicle on to the fl at bed , u se
the to w ing loop found in the vehicle tool s
and attach to the front or rear ancho rage
~ page 262 and ~page 262.
.&, WARNING
A veh icle being towed is not safe for pas­
sengers. Neve r allow a nyone to ride in a
vehi cle be ing towed, fo r any reason.
-
•
•
•

264 Emergency situations
fall from a lift if there is a change in ve­
hicle weight distribution and balance.
This might happen, for example, when
heavy components such as the engine
block or transmission are removed .
- When removing heavy components like
these, anchor vehicle to hoist or add cor­
responding weights to maintain the cen­
ter of gravity. Otherwise, the vehicle
might tilt or slip off the hoist, causing
serious personal injury.
(D Note
- Be aware of the following points before
lifting the vehicle:
-The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing, the
front or rear axle or the body side
members. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.

complexity of today's automobi les, have
steadi ly reduced the scope of maintenanc e
and repairs which can be carried out by vehicle
owners.
Also, safety and env ir onm ental con­
cerns p lace very strict limits on the nature of
repairs and adjustments to engine and trans ­
miss ion pa rts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing dev ices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure prope r
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliability
of your vehicle and even vo id your vehicle war­
ranty. The refo re, p roof of servic ing in accord­
ance w ith the ma intenance sched ule may be a
condition for upholding a poss ible war ranty
claim made within the warranty period.
Above all, operational safety can be adversely
affected, crea ting unnecessary risks for you
and your passengers.
I f in doubt about any servicing , have it done
by your authorized Audi dealer or any other
p roperly equipped and q ualified workshop .
We strong ly urge you to give your aut horized
Audi dealer the opportunity to perfo rm all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and trained spec ialists to keep your vehicle
running properly .
Performing limit ed m aintenance you rself
The fo llowing pages describe a limited num­
ber of procedures which can be performed on
your vehicle with ordinary too ls, should the
need arise and trained personnel be unavaila­
b le. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and carefully follow the instruc­
tions given. Always rigorously obse rve the
WARNINGS provided .
Before you check anything in th e engine
compartment, a lways re ad and heed all
WARNINGS ~&. and
~page 210 .
Con sumer In formation 269
_& WARNING
- Ser ious personal injury may occur as a re­
sult of improperly performed mainte­
nance, adjustments or repa irs .
- Always be extremely careful when work­
ing on the vehicle . Always follow com­
monly accepted safety pract ices and gen­
era l common sense. Never r isk personal
injury.
- Do not attempt any of the maintenance,
checks or repairs descr ibed o n the fol­
lowing pages if you are not fully fam ilia r
with these or other procedures with re­
spect to the vehicle, or are uncertain how
to p roceed .
- Do not do any work without the proper
too ls and equipment. Have the necessary
wo rk done by your authorized A udi deal­
er or another proper ly equipped and
qualified workshop.
- The engine compartment of any motor
veh icle is a potentially ha zardous area.
Never reach into t he area around or
touch the rad iator fan . It is temperature
contro lled and can switch on suddenly -
even when the engine is off . T he radiato r
fan switches on automat ically when the
coo lant reaches a certain tempera ture
and will cont inue to run until the coo lant
temperature drops .
- Always sw itch o ff the ignition before any­
one gets under the vehicle.
- Always support your veh icle with safety
s tands if it is necessary to work under­
neath the vehicle. The jack s upplied with
the vehicle is not adequate for this pu r­
pose and cou ld collapse causing serio us
personal injury.
- If you m ust wor k underneath the vehicle
with the wheels on the g round, a lways
make sure the vehicle is on leve l ground,
that the wheels are a lways securely
blocked and that the engine cannot be
started.
- Always make sure the transmission se­ lecto r lever (automatic transmission) is •
•

2 70 Con sum er Inf ormation
in P (Park position) and the park brake is
applied.
@) For the sake of the environment
- Changing the engine settings wi ll ad ­
versely affect emission levels . This is det­
rimental to the environment and increas­
es fue l consumption .
- Always observe env ironmental regula­
tions when disposing of old engine oil,
used brake fluid, dirty engine coolant,
spent batteries or worn out tires.
- Undeployed airbag modules and preten­
sioners might be classif ied as Perchlo­
rate Material -spec ial handling may ap­
ply, see www .dtsc .ca .gov/hazardous ­
waste/perch lorate . When the veh icle o r
parts of the restraint system including
airbag modules safety belts wit h preten­
s ioners are scrapped, all appl icable laws
and regulations must be observed. Your
a utho rized Audi dea ler is familiar with
these requirements and we recommend
that you have your dealer perform this
serv ice for you .
Additional accessories,
modifications and
parts replacement
Additional accessories and parts
replacement
Always consult an authorized Audi dealer be­
fore purchasing accessories .
Your vehicle incorporates the latest safety de ­
sig n features ensuring a high standard of ac­
tive and passive safety .
This safety could be compromised by non-ap­ proved changes to the veh icle. For this reason ,
if parts have to be replaced, p lease observe
the following points when installing addition­
a l accessories:
Approved Audi accessor ies and genuine Audi
parts a re ava ilable from authorized Aud i deal­
e rs. These dea
lers a lso have the necessary facili­
ties, tools and trained specialists to install the
parts and accessories proper ly .
A WARNING
=
Using the wrong spare parts or using non-
approved accessories can cause damage to
the veh icle and ser ious perso na l injury .
- Use on ly accessories express ly approved
by Audi and genuine Audi spare parts
- These parts and accessories have been
specia lly designed to be used on your ve­
h icle.
- Never install accessor ies such as tele­
phone crad les or beverage ho lders on a ir­
bag covers or within the airbag deploy ­
ment zones . Do ing so wi ll increase the
ris k of injury if a irbags are triggered in an
accident!
- Before you check anything in the engine
compa rtment, always read and heed a ll
WARNINGS
c:::> page 210 .
(D Note
-If items other than genu ine Audi spare
parts, add-on equipment and accessory
items are used o r if repair wo rk is not
performed ac cord ing to spe cified meth­
ods, this c an resu lt in seve re damage to
yo ur vehicle's eng ine and body (such as
co rrosion) and adversely affect yo ur vehi­
cle's warranty.
- If emergency repairs must be performe d
elsewhere , have the vehicle examined by
an authorized Audi dealer as soon as
possible.
- The manufacturer cannot be held liable
for damage wh ich occ urs due to failure
to comply with these stipu lations.
Technical Modifications
Our guidelines must be complied with when
t echnical modifica tions are made.
Always consult an authorized Audi dealer be-
fore start ing work on any modifications. ll>-

Consumption (fuel) ... ..... .. .. .. .. .. 2 7
Contact ing N HTSA .............. .... 129
Controls cleaning .......... .... .. .. . 203
Conven ience key
E mergency operation ... ... .. .. .. .. .. 75
I ndicator light . . . . . . . . . . . . . . . . . . . . . 7 5
Starting the engine (START ENGINE STOP button) .. .. ................. .. .... 73
Stopping the engine (START ENGINE
STOP bu tton) ............ .... .. .. .. 74
Sw itch ing the ign ition on ......... ... 73
un locking/locking ........... .... ... 34
Conven ience opening/closing .. .. .. .. .. 39
Conver tible c hild safety sea ts .. .. .. .. . 173
Convertible locking retractor
Activating . . . . . . . . . . . . . . . . . . . . . . . .
179
D eactivating ................ .. .... 180
Using to secure a c hild safety sea t
1.7 7, 179
Coolant
refer to Engine coo lant ..... ... ... .. 216
Coolant system
Adding coolant . ... .... ... .. .. .. .. .
2 17
Coolant leve l check ing ..... .. .. .. .. . 217
Eng ine coolant temperature gauge .. .. 12
Cooling mode (automatic clima te con trol
system) ..... .. ... .. ..... ... .. .. .... 66
Cooling mode (manua l cl imate control sys-
tem) ...... .. ................. .. .... 65
Cooling system Indicator lights . . . . . . . . . . . . . . . . . . . . 20
Cornering light .... ..... ... .. .. .. .. .. 42
C ruise control system
C hanging speed . . . . . . . . . . . . . . . . . . . . 80
D escr ipt ion . ............. .. .. .. .. ..
79
P rese lecting speed . . . . . . . . . . . . . . . . . . 80
Sw itching off .. .. ..... ... .. .. .. .. .. 80
switch ing on . ... .. .... ... .. .. .... .. 80
(upho lde rs . . . . . . . . . . . . . . . . . . . . . . . . . 5 7
Current consumpt io n . . . . . . . . . . . . .
26, 27
D
Data recorder . . . . . . . . . . . . . . . . . . . . . . 185
D ate display . ............. .... .. .... 10
Daytime running lights .......... ... ... 42
Inde x 275
Declarat ion of compliance
Adaptive cruise contro l .. .... ... .. ..
2 71
A udi s ide ass ist . ... . .. ... .... ... .. 2 7 1
Ce ll phone package ................ 271
Convenience key .. .... ............. 271
Electronic immob ilizer ............. . 271
Homelink universal remote con trol ... 271
Remote cont ro l key ............... . 271
Decorative parts/tr im cleaning .... .. .. 203
De fec tive light bu lb w arning
Ind icator light ..... . .. .. ..... ... .. . 2 4
Defrost ing (w indsh ie ld)
automat ic cl imate control system .. .. .
6 7
man ua l cl imate co ntrol system ... .. .. . 65
DEF (instrument clus ter) ......... .. .. .
11
Del uxe a utomatic climate control
refer to Climate contro l system (auto -
matic) .... .. .. .. ................. .
66
Determining co rrec t load l imit .... .. .. 234
D igital compass . . . . . . . . . . . . . . . . . . . . . 50
Dimensions ....... .. . .. .. ..... ... ..
266
D imming the rearv iew mi rror ..... .. .. . 49
D isplays cleaning .. ................. 203
D istance ... .. .. .. .. . .. ... .... ... .. .
27
Door/ rear lid warning . .. .. ...... .... .. 26
Door contact switch . . . . . . . . . . . . . . . . . . 45
Doors Child sa fety lo ck (mech ani cal) .... .. .. . 38
Driver informat io n system ........... ..
26
CD/rad io disp lay .. .. . .. .... .... .. .. . 26
Door/rear lid wa rni ng . ...... ... .... . 26
Drive r messages . . . . . . . . . . . . . . . . . . . . 14
E ff iciency program . . . . . . . . . . . . . . . . . . 28
Ind icator lights .... . .. .. ..... ... .. . 14
On-board computer .. .. ..... ... .. .. .
27
Outside temperature disp lay .. ... .. .. . 26
Serv ice interval display . . . . . . . . . . . . . . 13
U sing the mu ltifunction steering wheel .
26
Driver seating position ... ..... ... .. .. 122
D rive select
refer to Aud i d riv e select ........... . 102
D riving safely . . . . . . . . . . . . . . . . . . . . . .
121
Drivi ng throug h wate r ........... .. .. 194
Driving time . . . . . . . . . . . . . . . . . . . . . . . .
27
D ust filter
refer to Poll utant fi lter ......... .... . 64
•
•
•