transmission AUDI A4 1996 B5 / 1.G APB Engine Motronic Multiport Fuel Injection System Servising Workshop Manual
Page 10 of 90
24-8
 
  
8 - 
Sensor -1- for exhaust temperature -G235 
At rear of intake manifold on the left-hand 
side (looking from the front of the engine 
compartment) On vehicles with automatic 
transmission the Sensor -2- for exhaust 
temperature -G236 is located at this 
position see page   Page 24
-14
 . 
9 - 
Secondary Air Injection (AIR) Solenoid 
Valve -N112 
Only on vehicles with automatic 
transmission 
10 - 
Secondary Air Injection (AIR) Pump Motor 
-V101 Only on vehicles with automatic 
transmission 
11 - 
Sensor -2- for exhaust temperature -G236 On vehicles with automatic transmission 
the sensor is located with Sensor -1- for 
exhaust temperature -G235 at Position -8-. 
Both sensors are located behind each 
other  Page 24
-14
 . 
Pa
ge 10 of 90 Motronic Multi
port Fuel In
jection 
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1 
Page 11 of 90
24-9
 
  
12 - 
Recirculating valve for turbocharger -
N249 
13 - 
Fuel pressure regulator 
14 - 
Camshaft Position (CMP) Sensor 2 -G163 
Cylinder bank 2Previously identified as Camshaft Position 
(CMP) Sensor 2 -G40 
15 - 
Secondary Air Injection (AIR) Pump Relay 
-J299 Only on vehicles with automatic 
transmission 
16 - 
Motronic Engine Control Module (ECM) -
J220 
17 - 
3-pin harness connector For Engine Speed (RPM) Sensor -G28grey
18 - 
3-pin harness connector For Knock Sensor (KS) 2 -G66
19 - 
Harness connector for Heated Oxygen 
Sensor (HO2S) 2 -G108 and Oxygen 
Sensor (O2S) Heater -Z28 4-pin black
Pa
ge 11 of 90 Motronic Multi
port Fuel In
jection 
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1 
Page 13 of 90
24-11
 
  
26 - 
Valve -1- for camshaft adjustment -N205 
27 - 
Heated Oxygen Sensor (HO2S) -G39 with 
Oxygen Sensor (O2S) Heater -Z19 
28 - 
Knock Sensor (KS) 1 -G61 
29 - 
Knock Sensor (KS) 2 -G66 
30 - 
Engine Speed (RPM) Sensor -G28 
In transmission above sensor wheel
31 - 
Heated Oxygen Sensor (HO2S) 2 -G108 
and Oxygen Sensor (O2S) Heater -Z28 
Pa
ge 13 of 90 Motronic Multi
port Fuel In
jection 
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1 
Page 16 of 90
24-14
      
Component location for exhaust temperature 
sensors on vehicle with automatic 
transmission:  
    
Fig. 1  Component location for exhaust temperature sensors on 
vehicle with automatic transmission: 
1 - Sensor -1- for exhaust temperature -G235
2 - Sensor -2- for exhaust temperature -G236
Pa
ge 16 of 90 Motronic Multi
port Fuel In
jection 
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1 
Page 17 of 90
24-15
 
  
Intake manifold, removing and installing
 
Note:  
The procedure is described for vehicles with 
manual transmission. On vehicles with automatic 
transmission remove also the secondary air 
injection pump. 
-  Remove air distributor   Page 24
-43
 .
1 - 
Unclip Wastegate Bypass Regulator Valve 
-N75 from fuel rail. 
Pa
ge 17 of 90 Motronic Multi
port Fuel In
jection 
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1 
Page 29 of 90
24-26
      
Important Note:  
     After installing new engine control module, carry 
out the following operations: 
     - Check DTC memory and erase if necessary   
Page 01
-15
 . 
     - Perform adaptation of Throttle Valve Control 
Module -J338   Page 24
-146
 . 
     - Observe notes for coding new engine control 
module  Page 01
-93
 . 
     - On vehicles with cruise control (recognizable at 
steering column switch), activate cruise control 
function in the engine control module. 
     
       Repair Manual, Electrical Equipment, Repair 
Group 01
   
     - On vehicles with automatic transmission carry 
out adaptation for Kick-Down switch   Page 24
-
166
 . 
     - Generate readiness code   Page 01
-105
 . 
     - Perform adaptation of immobilizer to engine 
control module 
     
Pa
ge 29 of 90 Motronic Multi
port Fuel In
jection 
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1 
Page 31 of 90
24-27
      
Idle speed, checking
 
     
Test conditions  
     
No leaks in exhaust system 
     Coolant temperature at least 80 C 
     
Electrical consumers switched off (radiator 
fan must not run during the check) 
     A/C switched off 
     Pressure gauge not connected 
     Selector lever in position P or N (vehicles 
with automatic transmission) 
     
Checking idle speed  
     
Notes:  
     The idle speed cannot be adjusted.
     The idle speed is tested during the basic setting 
of the engine. 
Pa
ge 31 of 90 Motronic Multi
port Fuel In
jection 
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1 
Page 51 of 90
24-43
      
Fuel injection volume, fuel injector 
leakage and spray pattern of injectors, 
checking
 
     
WARNING! 
     
Fire hazard! The fuel system is pressurized. 
Before loosening hose connections or 
opening the test connection (to measure fuel 
pressure), place a cloth around the 
connection. Then release pressure by 
carefully pulling off the hose or cap. 
     
Test conditions  
     
Fuel pressure OK; testing   Page 24
-33
 . 
      To reach the fuel rail, the following steps must be 
performed on vehicles with manual transmission 
(without secondary air injection). On vehicles 
with automatic transmission (with secondary air 
injection) are minor differences in the work 
procedure.  
    
Several hoses must now be disconnected:  -  Unscrew bolts on air duct at points indicated (arrows) and remove air 
duct. 
-  Absolute cleanliness must be maintained.
Pa
ge 51 of 90 Motronic Multi
port Fuel In
jection 
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1 
Page 88 of 90
Rapid data transmission 
HELP
Select function XX
    
Indicated on display:  
-  Press buttons -0- and -8- to select function "Read Measuring Value 
Block" and confirm entry with -Q- button. 
Read Measurin
g Value Block
Enter display group number XXX
    
Indicated on display:  
Pa
ge 88 of 90 Motronic Multi
port Fuel In
jection 
(MFI
) system, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.1