lock AUDI A4 1996 B5 / 1.G Rear Seats Workshop Manual

72-61


7 -
Center mounting bracket clip
8 -
Bolt
8 Nm (71 in. lb)
9 -
Center mounting bracket
10 -
Locking stirrup
11 -
Rear panel
12 -
Trunk trim
13 -
Base plate
14 -
Bolt 8 Nm (71 in. lb)
Pa
ge 5 of 19 Rear seat
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.72.3

72-63


6 -
Bolt (4x)
16 Nm (12 ft lb)
7 -
Center mounting bracket clip
8 -
Bolt 8 Nm (71 in. lb)
9 -
Center mounting bracket
10 -
Locking stirrup
11 -
Rear panel
12 -
Trunk trim
13 -
Base plate
14 -
Bolt 8 Nm (71 in. lb)
Pa
ge 7 of 19 Rear seat
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.72.3

72-71

Lock for split rear backrest (Sedan and
Avant m.y. 1998), removing and
installing


- Remove screws -3- (2x).
- Push release lever -5- back and remove bolt -4-.
- Remove lock -6- from rear backrest -2-.
- When installing lock -6-, release lever -5- has to engage in groove for
release -1-.
Pa
ge 15 of 19 Rear seat11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.72.3

72-72

- Remove rear backrest upholstery in area near
lock.

- Remove screws -3- (2x).
- Remove release -1- downward out of rear backrest.
Pa
ge 16 of 19 Rear seat11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.72.3

72-73

Lock for split rear backrest (Avant m.y.
1998 ), removing


Removing lock trim

Removing lock lever - Remove bolt -2-.
Tightening torque: 1.5 Nm (13 in. lb)
- Remove bolt -5-.
Tightening torque: 5 Nm (44 in. lb)
- Pull lock trim -1- up and remove.
Lock trim removed
- Detach lock lever -4- from below from catches (2x).
- Lift up lock lever -4- using screwdriver.
Pa
ge 17 of 19 Rear seat11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.72.3

72-74

Removing locking cylinder

Warning indicator
Ignition key is required to remove and install locking cylinder -3- Locking lever -4- removed
- Using screwdriver, lift catches while simultaneously pressing out
locking cylinder -3-. When rear backrest is locked, pin -6- is 1-2 mm above lock trim.If rear backrest is not locked, pin -6- is approx. 20 mm above lock trim
-1- and a red mark is visible.
Pa
ge 18 of 19 Rear seat11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.72.3