AUDI A4 1996 B5 / 1.G Suspension Rear Drive Axle Remove And Install User Guide

42-101


8 -
Clamp
Always replaceTightening Fig. 1
9 -
Dished washer
Larger diameter (concave side) contacts
thrust ring Installation position Fig. 6
10 -
Spacer ring
Installation position Fig. 6
11 -
Circlip
Always replaceInsert into annular groove of shaft when
installing; not visible when joint installed
12 -
Outer CV joint O.D.: 89 mm (3.5 in.)Replace only complete jointRemoving Fig. 8Installing: drive joint onto shaft using
plastic-headed hammer until circlip
engages in groove Greasing Note, page 42
-99
Pa
ge 11 of 15 Rear drive axle, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.42.7

42-102


Fig. 1 Tightening clamp

Attaching the CV joint boot onto the outer body of the joint frequently
requires compressing or squeezing the boot. This produces a vacuum in
the joint boot, which may cause a crease to the inside when driving
(arrow).
For this reason, after installing the joint boot, vent it briefly by letting some
air in at the small diameter to balance the pressure and restore the correct
boot shape. Fig. 2 Venting CV joint boot
Pa
ge 12 of 15 Rear drive axle, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.42.7

42-103


Notes: Fig. 3 Removing inner CV joint
Use arbor to drive off boot first.Support ball hub.

Note:
Chamfer on the inner diameter of the ball hub (splines) must be facing
toward the shoulder of the drive axle. Fig. 4 Pressing on inner CV joint
- Press joint on up to stop.
- Install circlip.
Pa
ge 13 of 15 Rear drive axle, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.42.7

42-104


Fig. 5 Removing and installing circlip

Fig. 6 Installation position of dished washer and spacer ring
1 - Dished washer
2 - Spacer ring (plastic)
Pa
ge 14 of 15 Rear drive axle, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.42.7

42-105


Fig. 7 Installing dished washer in correct position

Fig. 8 Pressing off outer CV joint
- Clamp drive axle in vise using protective jaws.
- Remove clamp and push back boot.
- Screw in 3207 pressure spindle with M14-thread end into joint until CV
joint is pressed off splined shaft.
Pa
ge 15 of 15 Rear drive axle, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.42.7