ABS AUDI A4 1997 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Workshop Manual

01-25

Diagnostic Trouble Code
(DTC) Malfunction text
MIL switching
condition
SAE
VAG
P1600 18008 Power Supply (B+) Terminal 15 Low Voltage off
P1602 18010 Power Supply (B+) Terminal 30 Low Voltage immediately
P1606 18014 Rough Road Spec Engine Torque ABS-SG Electrical
Malfunction off
P1611 18019 MIL Call-up Circ./Transm. Control Module Short to Ground immediately
P1612 18020 ECM Incorrectly Coded immediately
P1613 18021 MIL Call-up Circ.Open Short to B+ immediately
P1746 00532 Repair Manual, 5 Spd. Automatic Transmission 01V

P1748 65535 Repair Manual, 5 Spd. Automatic Transmission 01V
P1813 00264 Repair Manual, 5 Spd. Automatic Transmission 01V
P1818 00266 Repair Manual, 5 Spd. Automatic Transmission 01V
P1823 00268 Repair Manual, 5 Spd. Automatic Transmission 01V
P1828 00270 Repair Manual, 5 Spd. Automatic Transmission 01V Pa
ge 36 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-141

Output on GST
and/or on VAG 1551
scan tool Possible malfunction cause

Malfunction repair
P1606 / 18014
Rough
Road/Acceleration
Sensor
Electrical Malfunction Was an exhaust test carried out in
which only the front axle was moved
and the rear axle was stationary?

- These conditions cause a malfunction to be
stored in the DTC memory. During exhaust tests,
the fuse must be removed from the ABS control
module. After the exhaust test, ABS control module
and engine control module DTC memory must be
erased.

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test
drive, check DTC memory again
MIL Status:
Malfunction not
displayed by MIL If there are ABS system
malfunctions, the malfunctions P1606 /
18014 are also stored in the engine
control module. Is a malfunction stored
in the ABS control module?

Repair Manual, Brake System On Board
Diagnostic (OBD), Repair Group 01, On Board Diagnostic (OBD)
- Check DTC memory of ABS control module

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test
drive, check DTC memory again

Wiring connection between Engine
Control Module (ECM) -J192- and
ABS control module -J104- faulty

- Check signal for rough road recognition from ABS
control module for ABS/EDL and/or ABS/ASR
page 24
-109

Notes:
Pa
ge 191 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

If a rough road is recognized by the ABS control module, the combustion misfiring recognition in the engine control
module is switched off by the "rough road info" from the ABS control module.
Pa
ge 192 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-143

Output on GST
and/or on VAG 1551
scan tool Possible malfunction cause

Malfunction repair
P1612 / 18020
ECM Incorrectly
Coded Malfunction P1606 / 18014 "Rough
Road Spec Engine Torque ABS-SG
Electrical Malfunction" also stored in DTC
memory
No
Yes

- Engine control module incorrectly coded

Cause: The vehicle is equipped with traction
control, but coding was done for vehicle
without traction control.
Remedy: code vehicle correctly according to
coding table.

Malfunction cause found: Yes
No

- Erase DTC memory, take test drive, after test
drive check DTC memory again
MIL Status:
Malfunction not
displayed by MIL Engine control module incorrectly coded


Cause: Vehicle is equipped with automatic
transmission, but was coded for manual
transmission or otherwise incorrectly coded
Remedy: code vehicle correctly according to
coding table.

Malfunction cause found: Yes


- Erase DTC memory, test drive, after test drive
check DTC memory again
Pa
ge 195 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-144

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1613 / 18021
MIL Call-up Circ.Open
Short to B+ Wiring connection between Engine
Control Module (ECM) -J192- and
Transmission Control Module (TCM) -J217-
faulty

- Check MIL wiring from Transmission
Control Module (TCM) -J217- page 24
-
105


Malfunction cause found: Yes
No

- Erase DTC memory, test drive, after test
drive check DTC memory again
MIL Status:
MIL lights up
immediately
Transmission Control Module (TCM) -
J217- faulty

Repair Manual, 5 Spd.
Automatic
Transmission 01V On Board Diagnostic (OBD), Repair Group 01
- Replace ABS control module -J104-

Malfunction cause found: Yes
No

- Erase DTC memory, take test drive, after
test drive check DTC memory again
For troubleshooting
Display group 027
Engine Control Module (ECM) -J192-
faulty

- Replace and code ECM -J192- page 01
-265
erase DTC memory and take
test drive check DTC memory
Notes:

This malfunction can only occur in connection with an automatic transmission.
Pa
ge 196 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-204
Display group 022
Notes:
Display group 022 should only be considered on vehicles with traction control (ATC).
Vehicles with traction control (ATC) can be recognized by the ATC indicator light in the instrument cluster and/or ABS (ATC)
On Board Diagnostic (OBD).
Repair Manual, Brake System On Board Diagnostic (OBD), Repair Group 01.

The wheel slip information for traction control (ATC) is calculated in the ABS control module. If slip is recognized, the ABS
control module requests a reduction in torque from the Engine Control Module (ECM). This torque reduction is divided into 12
reducing stages.
With a cold engine, coolant temperature less than 20 C (68 F), the reduction of engine torque is obtained:
With retarded ignition timing angle for lower reducing stages (1-5)
By brief shut-off of individual fuel injectors for higher reducing stages (6-12)
If the engine is warm, coolant temperature greater than 40 C (104 F), the engine torque reduction is obtained only by briefly
switching off individual fuel injectors.
Display shows
Display/specified value
Designation
Basic setting 22
1 2 3 4 0 - 12 1 = Reducing stages

_._ crankshaft
2 = Ignition timing point retarded by ATC (only with cold engine)
Pa
ge 287 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-248
Note:
The code number will be composed as shown in the following example:
- Audi A4 1
- Automatic 01V 5
- Front wheel drive without traction control: 0
- Vehicle with EGR: 0 1
- Code number: 0 1 0 5 1
Note:
Vehicles with traction control (ATC) can be recognized by the ATC indicator light in the instrument cluster and/or by ABS
control module identification using the ABS On Board Diagnostic (OBD) program.
Repair Manual, Brake System On Board Diagnostic (OBD), Repair Group 01.

Pa
ge 345 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1