AUDI A4 1997 B5 / 1.G AWM Engine Lubrication System Components Owner's Manual

17-21


- Lower subframe slowly using workshop crane 1202 A.
- Take out workshop crane VAG 1202 A.
- Remove bolts for oil pan/transmission:

- Remove M10 bolts -arrows-.
- Loosen bolts -1 to 18- diagonally.
Pa
ge 21 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-22

Note:

Unscrew both rear oil pan bolts -1- and -2- with attachment 3249. Turn the
flywheel on vehicles with a manual transmission -3- until the notch -arrow-
is aligned with the bolt.
- Take off oil pan. If necessary loosen it by striking lightly with a rubber
hammer.
- Carefully remove sealant residues from cylinder block (remove baffle
plate).

WARNING!
Wear protective glasses. - Remove remaining sealant from oil pan, e.g. with a rotating plastic
brush.
- Clean sealing surfaces: they must be free of oil and grease.
Pa
ge 22 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-23

Installing
Installation is carried out in the reverse order of
removal; note the following:

Note:
The oil pan must be installed within 5 minutes
after applying the silicone sealant.

- Cut off nozzle of tube at front marking (diameter of nozzle approx. 3
mm).

Silicone sealant D 176 404 A2
Thickness of sealant bead: 2 to 3 mm
Pa
ge 23 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-24

Note:
The bead of sealant must not be thicker than 3
mm, as otherwise excess sealant will enter the
oil pan and obstruct the strainer in the oil intake
pipe.

Note:
Be particularly careful when applying the bead of sealant around the rear
sealing flange (arrows in illustration). - Apply bead of silicone sealant onto clean sealing surface of oil pan, as
illustrated. (Illustration shows position of sealant bead on cylinder
block).
Pa
ge 24 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-25

- Immediately attach oil pan and tighten bolts in
described sequence:

Note: - Tighten bolts -1 to 18- diagonally to 5 Nm.
- Tighten bolts securing oil pan to transmission to 45 Nm.
- Tighten bolts M10 -arrows- to 40 Nm.
- Tighten bolts -1 to 18- tighten diagonally to 15 Nm.
Replace seals and gaskets.

When installing the oil pan with the engine removed from the vehicle,
ensure that the oil pan -3- is positioned flush with the intermediate
plate -1- at the flywheel end (i.e. oil pan should protrude dimension "a"
= 0.8 mm from cylinder block with respect to the cylinder block -2-). After installing oil pan assembly, the sealant must dry for approx. 30
minutes. Only then may the engine be filled with oil.
Pa
ge 25 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-26


Repair Manual, Suspension, Wheels, Steering, Repair Group 40

Vehicles with automatic transmission:
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 37

All models:
Vehicles with automatic transmission:
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 37 - Support subframe with workshop crane VAG 1202 A.
- Installing subframe:
- Secure ATF lines.- Install lock carrier Page 13
-1 .
- Fill engine with oil and check oil level.
- Check ATF level:
Pa
ge 26 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-27

Tightening torques

Component

Nm
Oil pan to cylinder block M7 15

M10 40
Oil pan to transmission 45
Limit stop for torque reaction support on oil
pan
28
Engine mounting to subframe 25
Engine mounting to engine support 25
Transmission support to transmission
support M10 40
Transmission mounting to subframe
M8
25
Oil return pipe to oil pan 10
Oil drain plug 30
Hose clamps for air duct hoses
3.5
Pa
ge 27 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-28

Oil pump, removing and installing


Removing

- Remove oil pan and baffle plate Page 17
-
11
.

- Remove bolt -2-.
- Remove sprocket wheel from oil pump shaft.
- Remove bolts -1- and -3- and remove oil pump.
Pa
ge 28 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-29

Installing
Installation is carried out in the reverse order of
removal; note the following:

- Insert dowel sleeves -Item 12 -, Page 17
-4 on
top of oil pump.


Oil pump shaft/sprocket wheel location: Can
only be installed in one position.

- Installing oil pan Page 17
-23

Tightening torques

Component

Nm
Chain sprocket to oil pump shaft 22
Oil pump to cylinder block 16
Pa
ge 29 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1

17-30


Oil pressure and oil pressure switch,
checking

Special tools and equipment

VAG 1342
VAG 1527 B
VAG 1594 A
Pa
ge 30 of 35 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.17.1