AUDI A4 1998 B5 / 1.G 01W Transmission Disassemble And Assemble Owner's Manual

34-56


Position of shift mechanism in transmission
Note:
Illustration is shown without the drive axle and pinion. 1 - Shift fork 5th and reverse gears
2 - Shift fork 3rd and 4th gears
3 - Shift fork 1st and 2nd gears
4 - Relay shaft
5 - Shift detent
6 - Shift rod

- Move transmission housing and engage 3rd gear (direction of arrow).
Pa
ge 21 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-57


- Install relay shaft -A-.
- Place inner shift rod -B- sideways into mounting hole in transmission
housing and assemble into mounting eye.
- Carefully turn shift rod in direction shown (arrow).

- Insert shift detent and tighten bolt (arrow) securely.
Pa
ge 22 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-58


- Install relay shaft stop bolts (arrows).
- Replace O-ring for multi-function switch.

- Carefully insert multi-function switch and tighten (arrows).
Pa
ge 23 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-59


Make sure dowel sleeves for transmission cover -A- are installed in
transmission housing -B-.
- Coat sealing surfaces with a thin layer of sealant AMV 188 001 02.
- Install transmission cover onto transmission housing.

- Install rear circlip (arrow) for input shaft ball bearing.
- Slide ball bearing onto input shaft.
Installation position: closed side of ball cage faces toward transmission
housing.
Pa
ge 24 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-60


- Press in ball bearing.
- Slide thrust piece -A- of press device onto input shaft.
- Position press device behind splines for clutch plate.
- Screw in bolts -B- and tighten slightly.
The bolts bear against the indentations in thrust piece -A-.
- Press in ball bearing onto seat by alternately tightening bolts -B- (1/2-
turn at a time) until stop is reached.

Notes: - Install front circlip -D- for input shaft ball bearing.
- Install spring washer -C-.
Position: convex side faces guide sleeve -B-.
Before installing guide sleeve, cover splines on input shaft with a
shrink tubing to protect the seal. Installing seal in guide sleeve Page 30
-18
.
Pa
ge 25 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-61


- Install guide sleeve -B- for throwout bearing.
- Install clutch release lever -A- and throwout bearing.
Pa
ge 26 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4