AUDI A4 1998 B5 / 1.G AHA Engine Multiport Fuel Injection And Ignition System Manual PDF

24-56


If display = Htg.aC.ON:
If display is switching between "Htg.aC.ON" and "Htg.aC.OFF" - Connect multimeter between harness connector terminals 1 and 2 (to
ECM), using VW1594 connector test kit.
- Measure voltage supply and check display in display group 40, display
field 4.
Specified value: 11.0-14.5 volts Specified value: 0.0-12.0 volts (oscillating)
Pa
ge 71 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-57
If there is no voltage:

If there is still no voltage: - Connect multimeter between harness connector terminal 1 (to ECM)
and vehicle Ground, using VW1594 connector test kit.
Specified value: 11.0-14.5 volts
- Check wiring between terminal 1 and relay panel using appropriate
wiring diagram.
Pa
ge 72 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-58
If there is voltage:

If display = Htg.aC.ON:
If display switches between "Htg.aC.ON" and "Htg.aC.OFF:" - Connect multimeter between harness connector terminal 2 (to ECM)
and Battery Positive Voltage (B+), using VW1594 connector test kit.
- Measure voltage supply and check display in display group 40, display
field 4.
Specified value: 11.0-14.5 volts Specified value: 0.0-12.0 volts (oscillating)
- Switch ignition off.
Pa
ge 73 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-59
If specified value is not attained:

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.

If wiring is OK: - Check wiring for open circuit between ECM/test box and 4-pin O2S
harness connector (to ECM).

Connector terminal 2 to ECM/test box socket 28
Specified value: max. 1.5
- Replace ECM -J220- page 01
-68
- Carry out adaptation of throttle valve control module to ECM page
24
-150
.
- Check readiness code page 01
-70
. If Diagnostic Trouble Code
(DTC) memory has been erased, or ECM was disconnected, generate
new readiness code page 01
-73
.
Pa
ge 74 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-60

Oxygen Sensor (O2S) aging, bank 1,
sensor 1, checking


Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable

Test requirements
Engine Coolant Temperature (ECT) at least
80 C (176 F)

Function test

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -4- to select "Basic Setting" function 04, and
press -Q- button to confirm input.
System in Basic Settin
g
HELP
Input display group number XXX

Indicated on display
- Press buttons -0-, -3- and -4- to input display group number 34 (034),
and press -Q- button to confirm input.
Pa
ge 75 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

System in Basic Setting 34 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 76 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-61

- Increase engine speed to 1800-2200 RPM.

- Maintain engine speed at 1800-2200 RPM until
display field 4 changes from "Test OFF" to "Test
ON."

- Maintain engine speed at 1800-2200 RPM and
compare display with specified values for
oxygen sensor aging (before TWC) in display
fields 3 and 4).

Note:
To be sure that the temperature is within the
specified range, the specified RPM has to be
maintained for at least 1 minute.

Display fields

1 2 3 4
Display group 34: Oxygen sensor aging (time period check of oxygen sensor) bank 1, sensor 1
Display xxxx RPM xx.xx ms xx.xx s Test OFF/Test ON
B1-S1 OK/B1-S1 n.OK
Indicates Engine speed
(in 40 RPM steps) Engine load Time period
Bank 1, Sensor 1 Diagnostic status
Diagnostic result
Range 0 - 6800 RPM 0.00 - 12.75 ms --- ---
Pa
ge 77 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

Specified value 1800 - 2200 RPM 0.8 - 2.5 ms 0.20 - 2.10 s B1-S1 OK

--- --- If not as specified page 24
-62
, Continuation
Pa
ge 78 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-62

Continuation
If displayed value is NOT OK (not as specified):

- Road test to condition oxygen sensor (eliminate
possible contamination) and repeat test.
If displayed value is still NOT OK:

- Replace HO2S -G39-.

- Check readiness code page 01
-70
. If
Diagnostic Trouble Code (DTC) memory has
been erased, or ECM was disconnected,
generate new readiness code page 01
-73
.
Pa
ge 79 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-63

Oxygen Sensor (O2S) aging, bank 2,
sensor 1, checking


Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable

Test requirements
Engine Coolant Temperature (ECT) at least
80 C (176 F)

Function test

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -4- to select "Basic Setting" function 04, and
press -Q- button to confirm input.
System in Basic Settin
g
HELP
Input display group number XXX

Indicated on display
- Press buttons -0-, -3- and -5- to input display group number 35 (035),
and press -Q- button to confirm input.
Pa
ge 80 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1