AUDI A4 1999 B5 / 1.G ATQ Engine Additional Signals Testing Service Manual
Page 41 of 44
24-196
Example 1:
From the DTCs stored in the memories, you have determined that control
module 1 is not communicating with control modules 2 and 3.
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder Control module
DTCs stored in DTC memories:
1
Missing signal from control module 2Missing signal from control module 3
2 Missing signal from control module 1
3 Missing signal from control module 1
- Switch ignition off.
- Disconnect the control modules connected across the bus wires and
check the bus wires for an open circuit. - Replace control module 1 if no malfunctions can be found in the bus
wires.
Pa
ge 41 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6
Page 42 of 44
24-197
Example 2:
From the DTCs stored in the memories, you have determined that control
module 2 is not communicating with control modules 1 and 3.
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder Control module
DTCs stored in DTC memories:
1
Missing signal from control module 2
2 Missing signal from control module 1Missing signal from control module 3
3 Missing signal from control module 2
- Switch ignition off.
- Disconnect the control modules connected across the bus wires and
check the bus wires for an open circuit. - Replace control module 2 if no malfunctions can be found in the bus
wires.
Pa
ge 42 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6
Page 43 of 44
24-198
Example 3:
Using the DTCs stored in the memories, you
have determined that none of the control
modules are sending or receiving signals.
Control
module
DTCs stored in DTC
memories:
1
Powertrain databus faulty
2 Powertrain databus faulty
3 Powertrain databus faulty
- Switch ignition off.
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder - Disconnect the control modules connected across the bus wires and
check bus wires for a short circuit to B+ and Ground (GND).
Pa
ge 43 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6
Page 44 of 44
24-199
If you cannot determine a cause for the DTC
"Powertrain databus malfunction, check
whether the DTC is caused by one of the
control modules.
All control modules that use the CAN-bus are still
disconnected. Ignition is switched off.
- Connect one of the control modules.
- Connect VAG 1551 scan tool. Switch ignition on,
and erase the DTC memory of the control
module you just connected. End scan tool output
using the "End Output" function 06.
- Switch ignition off and then on.
- Leave ignition on for 10 seconds. Then, read the
DTC memory of the control module you just
connected.
- If the DTC "Powertrain databus malfunction" is
displayed, replace the control module you just
connected.
- If the DTC "Powertrain databus malfunction" is
not displayed, connect the next control module
and repeat the procedure.
Pa
ge 44 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6